amber connect ASC300 Wireless GPS Tracker User Guide

June 5, 2024
amber connect

ASC300 Wireless GPS Tracker
User Guide

Overview

Accessories

  • Device
  • Bracket
  • User guide
  • Charger
  • Charge cable

Main Functions

  • Intelligent power saving
  • IPX5 water resistant grande
  • Tamper alert
  • Strong magnet installation
  • Fast charging
  • 10000mAh battery
  • Listen-in capability

Specification

Frequency: 900MHz GSM 850/900/1800/1900MHz
Location accuracy <10 meters
Monitoring range S5 meters
Working voltage/current 3.7V/60mA
Battery 10000mAh/3.7V industrial grade lithium polymer battery
LED Red: work status
Operating Temperature -20°C to 70°C
Dimension 1086130 mm
Weight 285g

My Device

Appearance

amber connect ASC300 Wireless GPS Tracker - Appearance

GSM Indicator

Status Meaning
Blinking quickly GSM initialization/No GSM
Blinking slowly Connect to the Amber Connect platform
Always ON Voice calling feature enabled

The GSM Indicator will turn off after the device has been powered on for 3 minutes.
Once the device is on, tap the power button to activate the LED, which will turn off automatically after 60 seconds.

SIM Card

The SIM card should have access to GPRS and SMS. Remove the device cover, switch to OFF and insert the SIM card.

amber connect ASC300 Wireless GPS Tracker - SIM Card

Installation

The device is built with a strong magnet which can be easily attached to any surface with a magnetic pull. To attach the device to a non-magnetic surface, use the 3M foam tape  and bracket included in your package.

Problems Causes Solutions
Poor signal The signal waves are unable to transmit when using the  GPS

tracker in places with poor signal reception, such as tall buildings or basements.| Relocate to an area with adequate signal reception.
Unable to boot| Power switch is OFF| Switch to ON
No battery| Charge battery
No SIM card| Insert SIM card
Unable to connect to thenetwork| SIM card inserted incorrectly| Check SIM card
SIM card has dust, debris| Clean SIM card
Invalid SIM card| Contact network supplier
Not in GSM service area| Move to GSM service area
Fail to locate| Poor signal| Move to an area with adequate signal reception
SIM has no access to GPRS| Contact network supplier to get GPRS service
Always reply “Address inquiry failed”| Contact supplier

Operation

Power ON/OFF
Power on: Press power button for 3 seconds (battery switch is in ON position).
Power off: Press power button for 3 seconds.

Emergency Number
Set emergency number via App.

Working Mode

  1. Tracking mode (default): GSM is always ON and location data uploaded in set time intervals.
  2. Ultra-long standby mode: device wakes up and uploads location data based on preset frequency set up to a maximum of 72 hours of location update.

Notice: In this mode, commands will NOT be executed until the device wakes up at preset time intervals. You can force the device to wake up and receive communication by:

a. triggering the tamper alert button at the back
b. unplugging the battery and plugging it in again.

Tamper Alert
The anti-tamper button will pop out and an alert will be sent if the device has been disassembled. In standby mode, an alert message will be uploaded and tracking mode will be  activated for 20 minutes if device disassembly is detected. After 20 minutes, the device enters into ultra-long standby mode.

Cover Remove Alert
The cover detection button pops out and an alert will be sent if the device cover is dismantled. In standby mode, an alert message will be uploaded and tracking mode will be  activated for 20 minutes if cover dismantling is detected. After 20 minutes, the device enters into ultra-long standby mode.

Low Battery Alert
When the battery is low, the device will activate a low battery alarm.

Vibration Alarm
The vibration alarm only works in tracking mode. To activate this function, please go to the Amber Connect.
App: safety > safety settings > vibration alert.

Geo-fence Alarm
The geo-fence alarm only works in tracking mode. When the vehicle enters/exits the pre-set geofence area, the Amber Connect App will send a real-time notification.

Voice Monitoring
Use pre-set SOS number to make and receive calls from the device. The device will automatically call back. Answer the call and monitor sounds inside the vehicle.

App And Web Platforms

Download App
Please download and install the Amber Connect App from your digital App store and follow the onscreen instructions to register your device.

Web App
Visit www.amberconnect.com/portal/customer/login and go to login > customer

sign up and follow the onscreen instructions to register your device.

Warning
Battery specified by the manufacturer is recommended. Maintenance or service arising from any third party accessories is not guaranteed. The manufacturer assumes no  responsibility for any damage caused by non-original accessories. Do not bend or open the battery. Do not immerse or burn the battery. Device disassembly is strongly  forbidden.

Non-professionals’ operation may lead to device damage.

Troubleshooting

If you are having trouble with your device, try the troubleshooting procedures before contacting a service professional.

Need help? Contact 2417 live support!

In App Chat support@amberconnect.com   

Chat via website www.amberconnect.com
Works with Android phones and tablets, ;Phone, ‘Pod. Compatible with Chrome, Mac and PC web browsers.

http://onelink.to/ng48h2

Amber Connect

Documents / Resources

| amber connect ASC300 Wireless GPS Tracker [pdf] User Guide
ASC300, Wireless GPS Tracker
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

amber connect User Manuals

Related Manuals