CALIBER CA 200P4 4 Channel Car Amplifier Max Output User Guide
- June 2, 2024
- CALIBER
Table of Contents
CALIBER CA 200P4 4 Channel Car Amplifier Max Output
Specifications
- Max power output at 14.4V: 4x 300W/4Q or 2x IOOOW/ 4Q (bridged)
- RMS output at 14.4V:4x IOOW/40 or 2x 320W/ 4Q (bridged)
- Frequency response Hz-51kHz
- Input Sensitivity RCA input 0,2 – 3V
- Low/high pass filter 50- 250Hz
- Total Harmonic Distortion <0,5%
- Signal-to-noise ratio (A-Weighted) >76dB
- Output Impedance 2- IQ
- Bass Boost 0-6-12dB · 45Hz
- Fuses 2x 35A (internal)
- Dimensions heatsink 380(Wl x 151(Dl x 50(Hl mm
- Total dimensions: 407(W) X 151(D) X 52(H) mm (Mounting feet and connectors)
OPTION 1
FEATURES
- Stereo output.
- Pulse Width Modulated (PWM) MOSFET Power Supply.
- Variable input sensitivity: RCA input 0.2V to 3V.
- Thermal-, Overload- and Shortcircuit protection.
- Excellent muting circuitry assures no turn on/off ‘pops’.
- Built-in High / Low Pass Filter
- Gold-plated power connectors for optimal power distribution.
- European design and engineering.
- Gold plated speaker connectors for optimal signal output.
MOUNTING
The amplifier has to have at least 5 cm (2″) ventilation space at all sides,
to allow the heat to rise away from the amplifier. Be sure that the power and
signal cables can enter and leave the amplifier in a straight line, to avoid
the risk of malfunction. Always place the power- and signal cables at opposite
sides of the vehicle to reduce any noise. The amplifier should be protected
from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5 mm
(1/8″) diameter holes at the marked locations and mount the amplifier using
the supplied self-tapping screws.
INSTALLATION
Remember to always disconnect the battery ground before working on a vehicle’s
electrical system! Always place a fuse or circuit breaker no more than 30 cm
(12″) from the battery, no greater than the fuse(s) of your amplifier for
optimal protection.
GETTING YOUR POWER STARTED
- First, the +12V terminal is connected directly to the battery of your car. Use a cable of at least 25 mm, and make sure that the connectors are of the same value.
- Don’t forget the extra “Vehicle protection ” fuse.
- The +12V terminal should NOT be connected to the car fuse box.
- Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the same mm’ cable as the positive cable (the same amount of power has to run through it). Ensure that all paint, undercoating, or any other insulation is removed from the area where you want to make your ground connection to.
- Third, the last cable to connect is your remote turn-on (REM). Many radio cassettes and CD- players have an output terminal for connection of the REM of an amplifier. If you don’t have such an output, a separate switch must be installed to control your amplifiers on/off function.
SIGNAL INPUT
The Caliber Amplifiers offer you two possibilities for your signal input.
- A High-Level input, using the loudspeaker output from your radio and the special High-Level input plug you found in the box.
- Signal input by using an RCA cable from your radio’s RCA outputs to the amplifiers signal input RCA’s.
- Connect the RCA outputs of your radio to the RCA input terminals of the amplifier.
- Take good care that you connect the Right output of your radio to the Right input of your amplifier, and that you connect the Left output of your radio to the Left input of your amplifier.
- Put the input level adjustment knob to the minimum.
- Put the volume of your radio to 3/4 of the maximum.
- Adjust the Bass Boost to your personal sound.
- Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully until you hear the amplifier begin to distort. A Caliber
- The amplifier “clips” very softly, so this can sometimes be a difficult adjustment.
- If you have turned up the Bass Boost to much, the amplifier will start clipping immediately. In that case, you must turn back the Bass Boost and start adjusting the input level again. You will hear that the Bass you wanted can be required in this way.
CALIBER WARRANTY
Due to the complexity of our products, we strongly recommend that this
amplifier is installed by your authorized Caliber dealer. If properly
installed by your dealer we provide a warranty for 12 months from the date of
purchase. If you install this amplifier yourself, we wish you lots of fun and
success in doing so. If you follow our guidelines, you’ll get the best result.
Our warranty, however, will be limited to and not exceed 30 days from the date
of purchase.
WARNING
Points to observe for safe usage Read this manual carefully before using this
item and its components. They contain instructions on how to use this product
in a safe and effective manner. Caliber Europe BV cannot be responsible for
problems resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem. Failure to do so may
cause personal injury or damage to the product. Return it to your authorized
Caliber Europe BV dealer for repair.
Product cleaning
Use a soft dry cloth for periodic cleaning of the product. For more severe
stains, please dampen the cloth with water only. Anything else has the chance
of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the room/vehicle is between +45′ C (+113′ F)
and O’ C (+3 2′ F) before turning your unit on.
Maintenance
If you have problems, do not attempt to repair the unit yourself. Return it to
your Caliber Europe BV dealer for servicing.
Placement
Place the product on a flat surface. Provide enough space around the product
for sufficient ventilation Do not locate the appliance,n the v1c1n1ty of a
heated surface or,n direct sunlight.
Accessories
Use only supplied accessories
References
- Smart Home, Audio, Beeld en meer! | Caliber Europe
- Smart Home, Audio, Beeld en meer! | Caliber Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>