CALIBER HDVD 002 DVD Player User Manual

June 4, 2024
CALIBER

HDVD 0020Manual

Specifications

Input: AC: 100-240V 50/60Hz
Power consumption: < 8W
Standby consumption: <0,5W
Operating temperature: 0~+45 °C
Operating humidity: 5~90%
Video output: 1.0 Vp-p (750)
Audio output: 2 Vrms (1KHz, 0dB)
Frequency response: 20Hz to 20kHz
Signal system; PAL/NTSC
Dynamic range: > 85dB (DVD/CD)
Signal-to-noise ratio: > 80dB (analog out only)
Laser: Semiconductor laser, Wavelength: 650nm
Compatible discs/files (Disc): CD/CD-RW/DVD/DVD-R/DVD-RW/DVD+RW/VCD/SVCD/

JPEG/MPEG4,AVI.MPG.
Compatible files (USB):| MP3/ .WMA/ .JPG/ .MPG/ VOB/ .DAT/ AVI/ .DIVX3-6/ -XVID files
Maximum resolution| 720×480/576 on these formats: AVI/DIVX/MPG/MPEG4/VOB/FLV
Built-in connections:| – HDMI 1.3 Output
480i/480P/576i/576P/720P/1080i/1080P
– Scart
– 2-channel audio RCA and composite video output
– USB port

  • supports 1.1 and 2.0
    «max. 32GB
    ¢ Output power: 5V/200mA
    Dimensions:| 225(w) x 53(H) x 233(0) mm

We are continuously improving/updating our products and product information.
It’s, therefore, possible that there is a slight difference between the description in this manual to the operation of the product.
If something is different or not clear; always check our website for the most current version.

Connection and button

CALIBER HDVD 002 DVD Player - fig

  1. DVD/CD tray
  2. (eject button)
  3. (play/pause button) (L:white / R: red) – to play/pause playback
  4.  (stop button) – Composite video output (yellow) – to stop playback
  5. (power button) – Coaxial video output (black) – turn the player ON/Standby
  6. USB – USB input standard size (max. 32GB)
  7. IR sensor – to receive remote control signals
  8. Display – Playback indication
  9. HDMI output connector – slide in/out DVD/CD tray – HDMI 1.3 digital signal output
  10. Audio output connector – to open/close DVD/CD tray – 2-channel RCA audio output
  11. Video output connector
  12. Coaxial output connector
  13. Scart output connector – Scart analog signal output – Output power: 5V/200mA (to be used with e.g. USB powered hard drive)

Precautions

Points to observe for safe usage
Read this manual carefully before using this item and its components. They contain instructions on how to use this product in a safe and effective manner. Caliber Europe BV cannot be responsible for problems resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Caliber Europe BV dealer for repair.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic.
Temperature.
Ensure that the ambient temperature is between 0°C and +45°C before turning on the device.
Maintenance.
If you have problems, do not attempt to repair the unit yourself. Return it to your Caliber Europe BV dealer for servicing.
placement.
Place the product on a flat surface. Provide enough space around the product for sufficient ventilation.
Heat. Do not locate the appliance in the vicinity of a heat surface or in direct sunlight.
Voltage. Check the main voltage indicated on the adapter/product rating label in accordance to the local electricity supply, if it doesn’t, return the product to the store where you bought it.
Plug. Remove the plug from the outlet, when the product is unused for a long period of time and during thunderstorms.
Accessories. Use only supplied accessories

Remote

  1. O button To switch the player ON/Standby

  2. 0-9 numbers Selects numbered items In a menu.

  3. MENU Opens the menu of a DVD or switches PCB ON/OFF on a VCD.

  4. UP Navigate up in menu selections.

  5. LEFT Navigate left in menu selections.

  6. DOWN Navigate down in menu selections.

  7. TITLE Press to return to the title menu of the DVD.

  8. VOL +I-Adjust volume

  9. STOP Mt – lx: to stop and resume later (press [ENTER] to resume). – 2x: to stop (later resume not possible)

  10. OSD To display the play time and status information Open/close the setup menu.

  11. SOURCE (read DVD or USB).

  12. L/R Select audio (language) track.

  13. NIP Select display mode.

  14. 44 Press repeatedly to playback fast forward in different speeds. The available speeds are; 2x. 4x . 8x, 16x and 32x. Press NI to return to normal speed.

  15. Press repeatedly to playback fast forward in different speeds. The available speeds are; 2x, 4x , 8x, 16x and 32x. Press NI to return to normal speed.

  16. a BUTTON To open/close the DVD/CD tray. ENTER Confirms or opens menu selection.

  17. MUTE Press to temporarily turn the sound ON/OFF.

  18. AUDIO – DVD: Press repeatedly during playback to hear different audio forms or available languages. – VCD: Press repeatedly during playback to hear different
    audio forms – VCD: Press repeatedly during playback to hear different audio modes. (Stereo, Left, or Right).

  19. GO TO Go to time, title or chapter in DVD mode.

  20. ANGLE Press to switch viewing angle options, works only for discs encoded with multiple camera angles.

  21. PROGRAM (DVD VCD CD) The program function allows you to store your favorite tracks on a disc. Press the button to open the on-screen menu. Use the number or arrow buttons to select titles, chapters or tracks. Select the [PLAY] option to play back your selection.
    Press [PROGRAM] and select [GLEAM to delete the Me list
    JPEG. Use the [PROGRAM] key to select a slide show mode by pressing cemetery. there ere 16 types not show.

  22. SETUP Viemthange settings. Use UP, DOWN LEFT, RIGHT to navigate and ENTER loODitarM.

  23. RIGHT Navigate to the right Si menu choices.

  24. ENTER Confirm sateen:ins in menus

  25. SUBTITLE Press repeatedly during pentad lo see different subtitle languages.

  26. ****Go to the previous chamerrtreck.

  27. ***Go to next chapter/1m.

  28. PLAY/PAUSE [ ****. Press to pause playback. Press again to resume playback.

  29. ZOOM Zoom the video/image DVD and VCD) – Press Room] repeatedly during playback of still pictures. or the please l moms to the following range: 2x lax 4x f lax; 113x 1 man’s size – Press [ZOOM] S a displayed photo (VCD) and enlarge/ reduce with Ihe 5/6 buttons. Use the buttons le scroll through the zoomed image.

  30. WIDE Change the aspect ratio 161.4:3 PS. 4:3 LB. TIM °pike is whalebone IN some enable fps n) movies.

  31. REPEAT Press during playback to select the desired repeat function. – DVD: You can repeal erepleirtiONNI • 1/CD/C13. You can repeat • traclUall of MP3/WIAA: You tan repeat a tracktkiderf

  32. SLOW Press the SLOW button le select slow playback and step-by. step speed. The speeds are itx.iNve.ine. and normal.

  33. A-B Sat A43-13 pcinl to view only title selected section

  34. STEP Press to pause playback, from this point you can go sleperp step through the images using the [STEP] key.

Let’s get this thing started
Connecting Video and Audio
Note: Before making or changing any connections. make sure that all the devices are disconnected from the point outlet
HDMI Output Requires an HDMI cable (not Included)

  1. Use the HDMI Output to Send audio & video from the DVD player to a television.
  2. Use an HDMI cable to connect the HOW Output on the rear of the DVD player to an HDMI input on your television.
  3. Adjust the connected televisions input Setting to match the input used in the previous step.

RCA Stereo Audio Output

  1. Use the RCA StereoAudio Output to send audio from the DVD player to a television or audio system.
  2. Rogues:5 an RCA audio cable (not included).
  3. Use an RCA audio cable to connect the RCA Stereo Audio Output to an RCA stereo audio input on your television or audio system.
  4. Adjust the connected television or audio systems input setting to match the input used in the previous step.

Coaxial Digital Audio Output

  1. Use the Coaxial Neat Audio Output to send high-quality audio from the DVD player to an audio system
  2. Requires a Coaxial digital audio cable.
  3. Use the coaxial cable to connect the Coaxial Digital Audio Output to a coaxial digital input on an audio system.
  4. Adjust the connected audio system’s input setting to match the input used in the previous step.
  5. In the Digital Out portion of the DVD players setup menu, adjust to PCM, RAW or off.

Composite Video Output

  1. Use the Composite Video Output to send video from the DVD player to a television.
  2. Requires an RCA video cable (not included).
  3. Use the RCA video cable to connect the Composite Video Output to a composite video Input on a television.
  4. Adjust the connected television’s input setting to match the input used in the previous step.

SCART Output

  1. Use the WART Output to send audio/video from the DVD player to a television.
  2. Require a SCART cable (not included).
  3. Use the SCART cable to connect the SCART output In the DVD to a SCART Input on a television.
  4. Adjust the connected television’s Input setting to match the input used in the previous step.

LOADING A DVD OR CD Loading a Disc

  1. Press the Open button to open the Disc Door.
  2. Load a disc into the DVD player tray. DVD label side facing up.
  3. Close the Disc Door. Mar a disc is loaded. it will begin playing automatically.

Playing a Loaded Disc

  1. Follow the instructions for loading a Disc
  2. If the disc does not begin playing automatically, press the Play/Pause button.

Programming a Loaded Disc

  1. Follow the instructions for Loading a Disc and Play-ing a Loaded Disc.
  2. While the loaded disc is playing, press the Program button on the remote.
  3. Use the Number Keypad to enter in the titles and chapters in the order you want to view them. DVD Turtles and chapters or CD tracks will play in the order they are programmed.
  4. Repeat step 3 until the desired DVD tides and chapters or CD tracks we programmed.

USB PORT
Connecting a USB Thumb Drive Conned a USB Thumb Drive to the USB Pon. Amassing the Content on a USB Drive

  1. Press the DVDIUSB button to enter DVD/USB mode
  2. The DVD player will index your USB flash drive and display potential compatible fees to playback
  3. Use the Up / Down arrow on the remote to highlight your file and press OK to playback

System setup

Press [SETUP] to open the setup menu. Use the direction buttons 1 ► – to select the preferred item. After finishing settings, press [SETUP] again to exit the menu.
General page
– TV display
Selects the aspect ratio of the playback picture.

  • 4:3 PS: if you have a normal TN/ and want both sides of the picture to be trimmed or formatted to fit your TV screen.
  • 4:3 LB: if you have a normal N. In this case, a wide picture with black bands on the upper and lower por-dons of the TV screen will be displayed.
  • 16:9: widescreen display. – Angle mark To turn the on-screen angle mark notification ON/OFF – Language setup You can select OSD language and select audio/subti-tle/menu language of DVD discs if available.

Troubleshooting

No power! no display on the front of DVD player once powered on:
– Always use the power button on the front of your DVD player to power it ON. The Standby button on the remote control will only work when the power button on the front of the DVD player has been switched to ON. – Check to ensure that the mains power plug is connected to the mains outlet and that the mains outlet is switched on.
No video display on TV once the DVD player is powered on: – Check that your audio/video cables are connected fully on both the DVD player and TV end. – Check that your N has been turned to the correct input channel. Usually, TVs have a remote control button titled something similar to INPUT or SOURCE to change between input connections available. Your N must be turned to the correct input channel for it to show the video from the DVD player.
Distorted video or black & white video only: – If using Scart cable check that the Scarf plug is fully pushed in to the socket on both the DVD player and the Tv.
– Clean your DVD disc to remove fingerprints, dust etc.
Unable to play OVD disc or playback stops: – If OVD player has been recently delivered or has not been used for some time leave the player powered on for 1-2 hours to clear any potential condensation that may have gathered inside the machine on the laser lens. This is a common problem after transportation or when a unit has been in storage but will clear when the player internals have fully warmed up.
– Check that your DVD disc is the correct way up in the DVD player tray. The printed surface of the DVD should be facing upwards in the DVD tray.
– Clean your DVD disc to remove fingerprints, dust etc.
Remote control! won’t work:
– Always ensure there is a clear line of sight between the player and the remote control. Cupboard doors, plant vases etc sitting between the player and remote control can stop the remote control signal from reaching the player.
– Change the remote control batteries. Always test a remote control with a brand-new set of good-quality batteries. Do not mix old and new batteries.
– Check to make sure the batteries in the remote control are the correct way around.
– Try the remote control closer to the DVD player
Caliber hereby declares that the item HDVD002 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU (RED), 2009/125/EC (ErP) and 2011/65/EU (RoHS).

**** Old appliances and/or batteries must not be disposed of with garbage!
If the device/battery can not be used anymore, every user is legally obliged to dispose of old appliances and/or batteries separated from the garbage, e.g. at a collection point of his municipality/district.

CALIBER HDVD 002 DVD Player - icon 5APPAREIL ET
EMBALLAGES A TRIER
Pour en savoir plus : www.quefairedemesdechets.fr
WWW.CALIBEREUROPE.COM
CALIBER EUROPE BV : Kortakker 10 – 4264 AE Veen : The Netherlands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals