Ibiza MHSPOT30-FX 2-In-1 Spot and Animation LED Moving Head Instruction Manual

Ibiza MHSPOT30-FX 2-In-1 Spot and Animation LED Moving Head

SAFETY PRECAUTIONS

For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit!

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the
  risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when the cover is removed.

• Only mount this unit in an area that will allow proper ventilation. Allow about 15cm between this device and a wall.

• Do not attempt to operate this unit, if it is damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• Always mount this unit in safe and stable way.

• Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer.

• Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

  • Objects have fallen, or liquid has been spilled into the appliance.
  •  The appliance has been exposed to rain or water.
  •  The appliance does not appear to operate normally or exhibits a marked change in performance.

MOUNTING

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any de-formation. When installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and unit. If you lack these qualifications, do not attempt the installation yourself.

• The installation should be checked by a skilled person once a year
• Mount the fixture either hanging upside-down from a ceiling/truss or set on a flat level surface. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails
• NOTICE: The suitable environmental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting fixture in an environment where the temperatures are under or above the temperatures stated above. This will allow the fixture to run at its best and help prolong the fixture life.
• Screw one clamp via a M12 screw and nut to the included bracket. Attach the bracket using the included screws to the bottom of the fixture. Attach the eyehole screw to the bottom of the base and pull the safety-cable through the screw and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw.

DMX SET UP

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer cable runs are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4W resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to termi-nate the line. Using a cable terminator will decrease the possibilities of erratic behavior.

DISPLAY MENU

• DMX Address Mode
  Setting of the DMX address: Press MENU to select Addr, press Enter to start setting. Use the UP or DOWN keys to set the desired Address. Then press Enter to confirm.

• DMX Channel Mode
  Selection of the channel mode: Press MENU to select Chnd. Press Enter to start setting Select the channel mode via the UP or DOWN keys: successively 9CH and 11CH. Press Enter again to confirm your selection.
  9CH: 9Channel mode

• Master/Slave Mode
  Setting the Master-slave mode: Press MENU to select SLnd. Then press Enter to start set-ting. MAST, SL1 will be displayed. Press UP or DOWN to choose Master or slave, then press Enter again to confirm your selection.

  • MAST: Choose the device as master
  • SL1: Choose the device as slave

• Auto or Music-controlled Mode
  Select between Auto Or Sound-controlled Mode: Press MENU to select ShNd. Press Enter to start setting. Auto & SoUn will be displayed. Choose Auto for auto running of the unit. Choose SoUn and the unit will follow the rhythm of the music. Press Enter to confirm your choice.

• Sound Sensitivity
  Adjustment of sound sensitivity: Press MENU, select SEns and press Enter to start set-ting. Use the UP and Down keys to adjust the sound sensitivity from 0-100. Press Enter to confirm your choice.

• Pan Reverse
  This option is set to reverse the Pan direction. Press MENU, select Pan, press Enter to start setting, UP and Down to select no or Yes, then press Enter to confirm your choice

• Tilt Reverse
  This option allows the user to reverse the Tilt direction: Press MENU, select tiLt, press Enter to start the setting. Use the UP and Down keys to select no or Yes, then press Enter to confirm your choice.

• Display Reverse
  This option allows the user to reverse the direction of the display panel. Press MENU, select dISP. press Enter to start the setting. Use the UP and Down keys to select dSIP and it will reverse directions. Press Enter to confirm your choice.

• Auto Test
  This option triggers an Auto test of the unit. Press MENU, select test, press Enter and the unit will run an auto-test.

• Reset
  Press MENU, select rSEt, press Enter key and wait for 1-3seconds. The light will be reset

• USE OF THE MOTOR OFFSET FUNCTION :
  Press “MENU” button, then press “ENTER” for at least 5 seconds. The unit will switch into Offset Mode. Press UP and DOWN to adjust the motor position of Pan, Tilt, Gobo and Color.

DMX CHANNEL

DMX mode

Function

| ****

Value

| ****

Percent / Setting

| Mode

9CH

| Mode

11CH

---|---|---|---|---
Pan| 000-255| 0~100%| 1| 1
Pan Fine| 000-255| 0~100%|  | 2
Tilt 1| 000-255| 0~100%| 2| 3
Tilt 1 Fine| 000-255| 0~100%|  | 4
Pan/Tilt Speed| 000-255| Fast -> Slow| 3| 5

Color

| 000-008| White| ****

4

| ****

6

009-017| White + Color 1
018-026| Color 1
027-035| Color 1 + Color 2
036-044| Color 2
045-053| Color 2 + Color 3
054-062| Color 3
063-071| Color 3 + Color 4
072-080| Color 4

Function

| ****

Value

| ****

Percent / Setting

| Mode

9CH

| Mode

11CH

---|---|---|---|---
 | 102-107| Opposite Two Part Green|  |
 | 108-113| Opposite Two Part Blue|  |
 | 114-119| All Red|  |
Halo Effect| 120-125

126-131

| All Green

All Blue

| 8| 10
 | 132-179| All Full color|  |
 | 180-217| Color Gradual Change|  |
 | 218-255| Color Jump Change|  |
 | 000-027| No Function|  |
 | 028-082| Sound Activity|  |
 | 083-112| No Function|  |
Auto Mode| 113-168| Auto Run| 9| 11
 | 169-199| No Function|  |
 | 200-239| Reset|  |
 | 240-255| No Function|  |

FUSE REPLACEMENT

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse. Be sure not to confuse the spare fuse with the active fuse.
Warning: If after replacing the fuse you continue to blow fuses, STOP using the unit. Contact customer support for further instructions. Continuing to use the unit may cause serious damage.

CLEANING

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outer case.
2.  Use a brush to clean the cooling vents and fan grill.
3. Clean the external optics with a glass cleaner and a soft cloth every 20 days.
4.  Clean the internal optics with a glass cleaner and a soft cloth every 30-60 days.
5.  Always be sure to dry all parts completely before plugging the unit back in.

TROUBLE SHOOTING

Listed below is a problem that you may encounter, with a solution.

No light output from the unit;

1. Be sure the fuse has not blown. The fuse is located on the rear panel inside the power socket. See Fuse Replacement.
2.  Be sure the fuse holder is completely and properly seated.

Auto Sensing Voltage: This fixture contains an automatic voltage switch, which will auto sense the voltage when it is plugged into a power source.

SPECIFICATIONS

• Total power: ………………………………………………………………………………………………………………………………………………… 55W
• Light source: ……………………………………………………………………………… 30W white 4in1 LED, 12pcs 5050 RGB 3in1 LED
• Color wheel: …………………………………………………………………………………………………..7 color + open , rainbow -flow effect
• Gobo wheel: …………………………………………………………………………………… 7 gobo + open, gobo – flow effect, gobo shake
• Focus………………………………………………………………………………………………………………………………………………………..Manual
• Beam angle: ………………………………………………………………………………………………………………………………………… 13 degree
• Movement: ………………………………………………………………………………………………………….. Pan 540degree, Tilt 210degree
• Control mode: …………………………………………………………………………………………DMX512/Master-Slave/Auto run/sound
• DMX Channel: ……………………………………………………………………………………………………………………………………..9CH/11CH
• Display: ……………………………………………………………………………………………………………………………………………. LED display
• Operating modes……………………………………………….8 internal programs , sound mode can be controlled by DMX 512
• Dimming: ………………………………………………………………………………………………………………………………………….. 0% – 100%
• Strobe: ……………………………………………………………………. Random function for strobe / pulse effect, from slow to fast
• Cooling system……………………………………………………………………………………………………………………………………………… Fan
• Dimensions: ……………………………………………………………………………………………………………………….. 160 x 145 x 300 mm
• Weight: …………………………………………………………………………………………………………………………………………………… 2.74 kg

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.

Prodaja in zastopa:
Lajbi d.o.o, Partizanska cesta 5, Celje, Slovenija
info@lajbi.com
www.lajbi.com

Imported from China by LOTRONIC S.A.
Avenue Zénobe Gramme 9
B-1480 Saintes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>