LECTRO 0706 LED Panel Heater Owner’s Manual

OWNER’S MANUAL

SAFETY

• By ignoring the safety instructions the manufacturer cannot be held responsible for the damage.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Never move the appliance by pulling the cord and make sure the cord cannot become entangled.
• The appliance must be placed on a stable, level surface.
• The user must not leave the device unattended while it is connected to the supply.
• This appliance is only to be used for household purposes and only for the purpose it is made for.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• To protect yourself against an electric shock, do not immerse the cord, plug or appliance in the water or any other liquid.

WARNING

• WARNING: In order to avoid overheating, do not cover the heater.
• WARNING: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Joists, beams and rafters shall not be cut or notched to install the appliance.
• Please do not install the appliance close to curtains and other combustible materials. This could cause a fire.
• The appliance shall, under no circumstances, be covered with insulating material or similar material.
• The heater must not be located immediately below a socket-outlet.
• Do not use this heater if it has been dropped.
• WARNING: The heater must not be used if the glass panels are damaged.
• Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
• WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• WARNING: To reduce the risk of fire, keep textiles, curtain, or any other flammable material a minimum distance of 1m from the air outlet.
• The heater needs to be installed so that the switches and other controls cannot be touched by a person in the bath or shower.

INSTALLATION

FOOT ASSEMBLY

• Before using the heater, the feet must be fitted to the unit.
• These are to be attached to the base of the heater using the screws provided.

WALL MOUNTING

• Please note that the product must be installed at least 15cm from the floor and 50cm from the ceiling.
• Install the bracket with the provided screws.
• Drill the holes in the wall on each side, then insert the plastic expanded plugs and fix the bracket in the wall with the screws provided.
• Place the heater in a suitable position and ensure that the holes are aligned with the bracket.
• Tighten the screws on top of the bracket.

BEFORE THE FIRST USE

• Place the device on a flat stable surface and ensure a minimum of 15cm free space around the device. This device is not suitable for installation in a cabinet or for outside use.
• Put the power cable into the socket. (Note: Make sure the voltage which is indicated on the device matches the local voltage before connecting the device. Voltage 220V-240V 50/60Hz)
• When the device is turned on for the first time, a slight odour will occur. This is normal, ensure adequate ventilation. This fragrance is only temporary and will disappear soon.
• During heating up and cooling down there may be some noise caused by the heater casing expanding and contracting, this is normal and does not indicate any fault.

DISPLAY/TOUCH BUTTON FUNCTIONS

• Press the power touch button to set the functions. The display will show what function is active.
• Use the mode button to adjust to low or high power. The upper symbol on the display is for high power, the lower one indicates the low power setting.
• Press ‘temperature up’ or ‘temperature down’ buttons to regulate the temperature you desired. The temperature can be set between 5°C and 50°C.
• Press the timer button to select the desired range between 1 hour to 24 hours. The set time will disappear after a few seconds.
• To enable the child lock HOLD down the ▲ button for 5 seconds and the lock symbol will appear on the display.
• To disable the child lock HOLD the ▼ button again for 5 seconds and the lock symbol will disappear.
• Once the child lock is active you cannot operate any of the heater touch functions.

USING THE HEATER WITH SMART LIFE APP

http://e.tuya.com/smartlife

• The heater can be used manually with its built-in controls or you can use a smart  phone or smart speaker to control it. Before you begin, ensure the app is downloaded. Theapp is available on Android and iOS.

PAIR YORUR HEATER TO SMART LIFE APP

• Make sure your heater is powered.
• Open Smart Life APP.
• Create an account or if you already have a Smart Life account, please log in using those details.
• Add a new device.
• Select the device you want to connect.
• Follow the instructions on the app to connect the heater.
• To control your device with voice using a smart speaker please refer to the manufacturer’s instructions on how to enable a skill through your device.

TECHNICAL SPECIFICATION

Voltage: 230V
Frequency: 50/60Hz
Power: 2000W

CLEANING AND MAINTENANCE

• Before cleaning, unplug the appliance and wait for the appliance to cool down.
• Clean the appliance with a damp cloth. Never use harsh and abrasive cleaners, scouring pad or steel wool, which damages the device.
• Clean the two air outlets (above and below) by using a vacuum cleaner to remove dust from inside.

ENVIRONMENT

This appliance should not be put into the domestic garbage at the end of its durability, but must be offered at a central point for the recycling of electric and electronic domestic appliances. This symbol on the appliance, instruction manual and packaging puts your attention to this important issue. The materials used in this appliance can be recycled. By recycling of used domestic appliances you contribute an important push to the protection of our environment. Ask your local authorities for information regarding the point of recollectio Confinity NV, Dorp 16, 9830, Sint-Martens-Latem, Belgium declares the following device in sole responsibility:
Brand name: Vlectro
Product type: LED panel heater 2000W
Item number: VL-LEDPANBL2000 / VL-LEDPANWH2000
Complies with the following harmonization rules:
EN 62233:2008 PAK-Anforderung für GS (PAH requirement for GS) AfPS GS 2019:01 PAK
EN 60335-230:2009+A11:2012+A1:2020+A12:2020
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A2:2019+A14:2019+A15:2021 Low
Voltage Directive 2014/35/EU COMMISSION REGULATION (EU) 2015/1188 of 28 April 2015 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for local space heaters; (EU) 2016/2282 EN 60675:1995+A1:1998+A2:2018+A11:2019 EN 50564:2011
Sint-Martens-Latem, Belgium – JULY 2023
A.Pappijn – Product Manager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>