TREND A9000126-16-S 16 Lights 17 Inch Chandelier Instruction Manual
- June 3, 2024
- trend
Table of Contents
TREND A9000126-16-S 16 Lights 17 Inch Chandelier
A9000126-16-S
INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need them at a later date.
CAUTION
WARNING : Risk of Fire. Consult a qualified electrician to ensure correct
branch circuit conductor. Min 90ºC supply conductors.
Turn off the main power at the circuit breaker before installing the fixture,
in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local and National
Electrical Code (N.E.C.) standards. If you are unfamiliar with proper
electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no
parts are missing by referencing the illustrations on the installation
instructions.
ASSEMBLY AND INSTALLATION
-
Loosen the screw(17) that is near the cut end of the safety cable(16), Pull out the cut end from
the hole of the sleeve, wrap the cable around a structural beam of your building. Finally, insert the cut end of the sleeve and secure it with screw. For further information, please refer to the instructions on the reverse side. -
Secure the mounting plate (8) to the outlet box(1) with box screws(6) and wood screws (7)
-
Pull out the outlet wire and ground wire from the outlet box. Make wire connections with Wire Connector(2)
–Black wire from light to Black wire (3) from power source.
–White wire from light to White wire(4) from power source.
–Loop the ground wire(5) to mounting plate (8) with a ground screw(9). -
Attach the canopy(10) against ceiling, secure with the ball nut(11) onto the mounting screw.
-
Remove the cover (15) from the socket , insert G9 bulb (14) (not included) into socket. Then slide the crystal shade(13) up to the glass holder. Finally, use the cover(15) to secure them.
DO NOT USE BARE HANDS TO TOUCH THE BULB.
- OUTLET BOX
- WIRE CONNECTOR
- BLACK WIRE
- WHITE WIRE
- GROUND WIRE
- BOX SCREW
- WOOD SCREW
- MOUNTING PLATE
- GROUND SCREW
- CANOPY
- BALL NUTS
- GLASS HOLDER
- K9 CRYSTAL
- G9 BULB
- COVER
- SAFETY CABLE
- SCREW
INSTALLATION INSTRUCTIONS
For Safety Cable
Please read carefully and save these instructions, as you may need them at a later date.
INSTRUCTION
This fixture is provided with a safety cable. The safety cable provides a back up system for the fixture’s frame and the installation hardware. It is essential that the safety cable be properly installed. The cable must be secured to a structural beam of the building, and not to the outlet box. The cable must be terminated with a sleeve specially sized for the cable per following the steps:
- Insert enough cable through one side of the sleeve to form a large loop
- Wrap the cable around the structural beam or fixture ceiling pan
- Turn back the cut end and insert the cable into the opposite side of sleeve
- Pull back on cable until desired loop size is obtained
- Allow 1/8” of cable cut end to extend beyond end of sleeve.
- Use two screws to make sure that it will not slip back into sleeve while hanging.
Refer to the figure for more detailed information.
Remark : Please make sure all hardware is properly tightened and that the cable is positioned clear of screws.
Customer Support
1500 Cherokee Parkway, Suite 100, Acworth, GA 30102
P: 866-845-5451 • F:
866-816-6165
E: service@acclaim-lighting.com • www
.acclaim-lighting.com
INSTALLATION IS NOW COMPLETE
Documents / Resources
|
TREND A9000126-16-S 16 Lights 17 Inch
Chandelier
[pdf] Instruction Manual
A9000126-16-S 16 Lights 17 Inch Chandelier, A9000126-16-S, A9000126-16-S
Chandelier, 16 Lights 17 Inch Chandelier, 16 Lights Chandelier, 17 Inch
Chandelier, Chandelier
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>