trend T11-CGS Clamp Guide Kit Installation Guide

: May 15, 2024
: trend

Table of Contents

trend T11-CGS Clamp Guide Kit
Product Information
Product Usage Instructions
SAFETY
ITEMS ENCLOSED & DESCRIPTION OF PARTS
ASSEMBLY
ENVIRONMENTAL PROTECTION
GUARANTEE
OPERATION
SPARE PARTS
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

trend T11-CGS Clamp Guide Kit

Product Information

Specifications

Model: T11 Clamp Guide Kit
Model Numbers: T11/VJS/CGKIT, T11/CGS/KIT
Version: INST/CGSK v2.0
Intended Use: For use with T11 plunge router to route parallel grooves in boards and timber
Lateral Adjustment: Maximum 12mm

Product Usage Instructions

Intended Use
This accessory is designed to be used with a T11 plunge router and a suitable Clamp Guide for routing parallel grooves in manmade boards and natural timber with a compatible cutter. Use T11/VJS/CGKIT with VJS clamps and T11/CG/KIT with CGS clamps.

Assembly

Isolate the router from the power supply.
Place the center bracket over the two tapped holes in the upper section of the T11 router base.
Secure the bracket using the two machine screws and hex key provided in the kit.
Ensure the component is clamped securely before use.

Environmental Protection
Recycle raw materials instead of disposing of them as waste. Sort accessories and packaging for environmentally friendly recycling. At the end of its life, the product and its accessories should be sorted for environmental-friendly recycling.

Guarantee
All Trend products are guaranteed against defects in workmanship or material, except for damages due to improper use or maintenance.

FAQ (Frequently Asked Questions)

Q: Can this clamp guide kit be used with any router?
A: No, this kit is specifically designed for use with the T11 plunge router. Ensure compatibility before use.
Q: What is the maximum lateral adjustment of this clamp guide kit?
A: The maximum lateral adjustment is 12mm.

Thank you for purchasing this Trend product, which should give lasting performance if used in accordance with these instructions.
The following symbols are used throughout these instructions.
Denotes risk of personal injury , loss of life or damage to the tool in case of non-observance of the instructions.
Refer to the instruction manual of your power tool.
This unit must not be put into service until it has been established that the power tool to be connected to this unit is in compliance with 2006/42/EC (identified by the CE marking on the power tool.

INTENDED USE
This accessory is intended to be used with a T11 plunge router and a suitable Clamp Guide to allow parallel grooves to be routed in man-made boards and natural timber with a suitable cutter fitted.

Use T11/VJS/CGKIT with VJS clamps.
Use T11/CG/KIT with CGS clamps.
Lateral adjustment maximum 12mm.

SAFETY

Please read and understand the safety points at the end of this instruction as well as the power tool instructions before use.
PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.

The attention of UK users is drawn to The Provision of Use of Work Equipment Regulations 1998, and any subsequent amendments.
Users should also read the HSE/HSC Safe Use of Woodworking Machinery Approved Code of Practice and Guidance Document and any amendments.
Users must be competent in using woodworking equipment before using our products.
Attention should be made to the HSE’s Safe Use of Vertical Spindle Moulding Machines Information Sheet No.18 and any revisions.
Please keep children away from tools and work area.
All power tools will have a residual risk, so must therefore be operated with caution.
Only use tooling that meets EN847-1/2 safety standard and any amendments.
Consider working environment before using tools.
Ensure working position is comfortable.

ITEMS REQUIRED

T11 Router.
Variijig Clamp Guide or Clamp Guide System clamp.

ITEMS ENCLOSED & DESCRIPTION OF PARTS

$trend-T11-CGS-Clamp-Guide-Kit- $1$$

A. Centre block x1
B. Nylon guide for CGS or Nylon guide for VJS/CG x1
C. Guide rod 8mm x2
D. Thumb knob M6 x2
E. Thumb knob anti-vibration spring x2
F. Router fixing screw x2
G. Hex key 4mm x1
H. Instructions x1

ASSEMBLY

Isolate router from power supply before fitting the accessory kit.

Locate the centre bracket over the two tapped holes in the upper section of the T11 router base. Secure the bracket using the two machine screws & hex key.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing as waste.
Accessories and packaging should be sorted for environmental-friendly recycling. The product and its accessories at the end of its life should be sorted for environmental-friendly recycling.

GUARANTEE

All Trend products are guaranteed against any defects in either workmanship or material, except products that have been damaged due to improper use or maintenance.

© Trend Machinery & Cutting Tools Ltd. 2013 E&OE
® All trademarks acknowledged
Trend Machinery & Cutting Tools Ltd
Odhams Trading Estate St Albans Road
Watford WD24 7TR England
Tel: 0044(0)1923 249911
technical@trendm.co.uk
www.trend-uk.com

OPERATION

Slide the centre block and nylon guide together so they touch and then open up to about 5mm. Tighten the thumb knobs to lock the assembly together. Measure and mark position for the slot or groove. Mark second line 115mm for CGS and 102mm for VJS/CG away from this line, this is the offset. Position clamp guide so that inside edge of the clamp is on the offset line.

Fitted to CGS

Fitted to VJS/CG

Use a square to square up the clamp guide on the component. Secure clamp onto component.
Place the router with the accessory fitted so that the nylon block sits over the centre T slot of the clamp guide system or an outside edge on VJS/CG.
Set the cutter depth, by plunging down until cutter touches work piece, lock plunge and the set cutter height on depth scale.
Release plunge slightly to raise cutter by about 1mm.
Loosen the thumb knobs and adjust router position in or out so that the cutter edge is correct to cut line.
The accessory has a maximum of 12mm adjustment.
Once correct position is obtained lock thumb knobs.
Release plunge.
Switch on router, plunge down and move router assembly along clamp to the required groove length.
At the end of the cut, release plunge and switch off router.
Ensure working position is comfortable and component is clamped

Fitted to CGS

Fitted to VJS/CG

Ensure the guide is not clamped onto the waste piece. The material being cut will need to be supported and clamped securely.
Ensure all fixing screws are tight and do not foul the router. Always isolate router from power supply before making any adjustments.

If the slot needs to be made wider, isolate router, undo the two thumb knobs and pull the centre block and nylon guide apart by the required amount, then tighten the thumb knobs. After use remove the accessory from T11 router and store carefully.

SPARE PARTS

Please use only Trend original spare parts.

Item	Qty.	Desc.	Ref. (1 off)
A	1	Centre Block	WP-T11-CGS/1
B	1

1

MAINTENANCE

Please use only Trend original spare parts and accessories. The accessory has been designed to operate over a long period of time with minimum of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning.

Ensure switch and machine is isolated from power supply before carrying out any:

Cleaning
- Keep the grooves, threads and rods clear of sawdust and resin build up.
- Regularly clean with a soft cloth
Lubrication
- Accessory requires no additional lubrication.
Storage
- Always return product to its packaging after use.

Safety Points

Disconnect power tool and attachment from power supply when not in use, before servicing, when making adjustments and when changing accessories such as cutters. Ensure switch is in “off” position and cutter has stopped rotating.
Read and understand instructions supplied with power tool, attachment and cutter.
Current Personal Protective Equipment (PPE) for eye, ear and respiratory protection must be worn. Keep hands, hair and clothes clear of the cutter.
Before each use check cutter is sharp and free from damage. Do not use if cutter is dull, broken or cracked or if any damage is noticeable or suspected.
The maximum speed (nmax) marked on tool or in instructions or on packaging shall not be exceeded. Where stated, the speed range should be adhered to.
Insert the shank into the router collet at least all the way to the marked line indicated on the shank. This ensures at least 3/4 of shank length is held in collet. Ensure clamping surfaces are clean.
Check all fixing and fastening nuts, bolts and screws on power tool, attachment and cutting tools are correctly assembled, tight and to correct torque setting before use.
Ensure all visors, guards and dust extraction is fitted.
The direction of routing must always be opposite to the cutter’s direction of rotation.
Do not switch power tool on with the cutter touching the workpiece.
Trial cuts should be made in waste material before starting any project.
Repair of tools is only allowed according to tool manufacturers instructions.
Do not take deep cuts in one pass, take shallow passes to reduce the side load applied to the cutter.

Please see www.trend-uk.com/safety for more safety advice.

Our policy of continuous improvements mean that specifications may change without notice. Trend Machinery & Cutting Tools Ltd. cannot be held liable for any material rendered unusable, or for any form of consequential loss.