WEEFiNE 2500 Smart Focus Video Light User Manual
- June 8, 2024
- WEEFINE
Table of Contents
WEEFiNE 2500 Smart Focus Video Light
OVERVIEW
- Right Button
- Left Button
- Battery Level Indicator LED
- Light Head
- Tail Cap
- Flood Beam LED
- Red Beam LEDs
- Electric Flash Optical Sensor
- UV Beam LEDs
- Fiber Optic Connector (For remote control brightness)
The remote control is options accessories.
Standard Accessories
- Diving Light
- Battery
- Charger
- Spare O-rings
- User Manual
- O-ring Removal Tool
- Certification
- Guarantee Card
Specifications
FEATURES
Automatic Protection Against Overheating
When the light is used in areas in which the ambient temperature is higher
than 50°C, the light will automatically reduce the brightness by 50%. This
will reduce heat and protect the light components from damage.
Safety Mode
When the battery is almost exhausted, the light output drops automatically to
20%, the light turns off after enters Safety Mode in approximately 10 minutes.
Unable to switch the mode and adjust the brightness.
Battery Level Indicator
There are four colors to indicate the amount of power remaining in the
battery.
- Blue approx. 100%~80%
- Green approx. 80%~30%
- Red approx. 30%~10%
- Flash Red <10%
Installing the Battery
Insert the battery into the battery slot,as shown in the diagram below.
Warning!! The polarity of the battery must match the polarity of the
contacts on the light. Make sure that the positive and negative poles of the
battery aligh with the positive and negative poles of the light.
Charging the Battery
- Step 1: Insert the DC plug into the battery. (As shown in the diagram below).
- Step 2: Plug the charger into the wall outlet. The charger’s indicator will turn red signifying the charger is receiving power.
- Step 3: When the battery has finished charging, the charger’s indicator will turn green.
Noted: Charge time is approximately 2.5 hours
Attention: To protect the battery and extend battery life, please do not
charge the battery for more than 12 hours.
Sleeping model
When the light is on , press the right button for more than 2 seconds to enter
into sleeping model (Only the battery indicator is working).
Automatic Protection Against Overheating
When the light is used in areas in which the ambient temperature is higher
than 50°C, the light will automatically reduce the brightness by 20%. This
will reduce heat and protect the light components from damage.
GENERAL WARNINGS AND INSTRUCTIONS
- Do not disassemble the diving light.
- To avoid leaks the O-rings should be checked to ensure that they are free from any dirt, sand, hair and dust every time before you open and close the light. Use a soft cloth to the O-rings if required. The O-rings should also be carefully checked for cracks or blemishes. Gently and evenly apply a thin coat of grease to the entire O-rings regularly to prolong O-ring life.
- Be care not to scratch the O-ring surface. If cracks or blemishes occur, the O- rings should be replaced immediately.
- Do not open the light when using in the water.
- Wash the exterior of the light thoroughly with clean fresh water immediately after use. Soaking the light in fresh water will help to remove salt deposits prior to storage.
- Do not disassemble, modify, remanufacture, puncture, or damage the device or battery.
Operating Instructions
Turn on
Press the Right and Left button at the same time and hold them down for 0.5
second. When the light is turned on, press and release the left button for
entering into flood model at 100% brightness.
Turn off
Press the Right and Left button at the same time and hold them down for more
than 2 seconds.
Switch mode
Press the Left button for a short time. (Flood-Red-UV-Flood)
Adjust brightness
In the flood model, press the Right button to switch the brightness(100%→
50%→25%→300Lm→100%):
In the red model, press the Right button to switch the brightness(100%→
50%→25%→100%):
The UV brightness is not adjustable.
Flashing
When the light is off, press the Left and Right button at the same time for
more than 2 seconds to enter into flash model (Total 21 levels).
Increase flashing rate: press and immediately release the Right button.
Decrease flashing rate: press and immediately release the Left button.
Exit: Press the Left button for more than 2 seconds.
Automatic shut-off mode
When the light is on, press the Right button for more than 2 seconds to enter
into automatic shut-off mode (The battery indicator is flashing ).
BATTERY WARNINGS
- Remove the battery if the light will not be used for long period of time (e,g., between dive trips).
- Do not use a sharp object to remove the battery.
- Keep the battery away from children.
- Contact your local waste disposal department to dispose of the light/battery in accordance with applicable local laws and regulations.
- If using an external battery charger, only use the WEEFINE accessory approved for your product.
- Only replace the battery with the correct WEEFINE-approved replacement battery. Using an incorrect battery presents a risk of fire or explosion.
To purchase a replacement battery, see your WEEFINE dealer or the WEEFINE website.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>