wopet FT70 Castle Automatic Pet Feeder User Manual

Castle Automatic Pet Feeder
Model: FT70 & FT70 Plus

USER MANUAL

Product Specification

Assembly Guidelines

1.  Remove the bowl
   • First, press the (1) and (2) buttons inward while lifting the food tank at the same time. Remove the food tank, and take out the Type-c charging line, desiccant, instruction manual, etc.

2. Take out the lid
   •  Twist knob to open position, then lift lid up.
   

3.  Load desiccant
   •  Lift open the desiccant cap, place desiccant inside, and replace the cap.
   

4.  Battery installation
   • Lift open the battery covering as indicated, place 3 D-type batteries oriented according to the label, and close the battery covering after loading.
   

5. Insert power cable
   •  Insert the Type-c power cable as shown in the diagram. Wind the cable outward according to the direction indicated to avoid wire constriction.
   
   Notes: Although it is not necessary to use both modes at the same time, it is recommended to use both modes in order to prevent the feeder from losing power during any power interruptions

6. Bowl installation
   •  Place the bowl into the feeder base as indicated
   

7. Food tank installation
   •  Align the two buttons with the Food tank as indicated by the arrows in the diagram, and install them from top to bottom by pressing them into place.
   

8. Install the lid
   • First, twist the knob to the open position
   
   • Align with the notch position
   
   • Load into place, and then twist the knob to lock the lid
   

9. Cleaning the food tank
   • Press the (1) and (2) buttons inward simultaneously to release and remove the food tank for cleaning.
   

10.  Cleaning the turnplate
    • Open Link stopper from the feeder base.
    
    • Twist turnplate counter clockwise
    • Lift the turnplate up to remove it
    
    •  Install the turnplate, putting the turnplate into the feeder base.
    Align the turnplate with the base position indicated, and then place turnplate into the feeder base.
    • Turn the turnplate clockwise to the locked position, and then align and place the link stopper into the base slot
    

Panel Introduction

Buttons Overview

Note: Will lock automatically after 2mins of inactivity. Hold for 2s to unlock

•Press and hold for 2s to lock/ unlock other buttons and screen
| Return / Cancel button| •Return to the previous step
•Return to interface after setting up
| Number Increase button| •Press to increase the value
| Number Decrease button| •Press to decrease the value
| Manual button| • Must be Unlocked] Press to feed 1 portion
| Recording button| • Must be Unlocked] Hold for 3s and start recording after a beep is heard {max 10s}
•Recoding saved after a double beep is heard

Screen Panel Introduction

•Hold button for 2s to unlock
Clock indicator| Flash Indicates:
•Powered by adapter or battery.
Note: when flashing, press button to set up/ modify the current time
Timing [24-hours format]| •Local time
1 2 3 4 5 6
Meal| •Number of meals
Battery Level| •Lights up when running on battery power Turns red to indicate low battery

Setting Guideline

Step 1 — Setting Current Time

Note: Clock icon flashes when powered as shown in fig.(01).
[If Screen is Locked]
Press and hold for 2s to unlock screen as shown in fig.(02).

TIP: Please note the conversion between 24-hour format and 12-hour format.
Example: 9:00AM = 9:00; 10:00PM = 22:00 More as below
12-hour Clock =24 hour Colck Comparison Chat

STEP 1.2— Minute Setting

[ Must be Unlocked ]
After setting hour, press   to move to set the “minute” of the time. press to set the “minute”. (Press to modify if needed) Press   to save.

STEP 1.2— Minute Setting
[ Must be Unlocked ]
After setting hour, press to move to set the “minute” of the time. press to set the “minute”. (Press   to modify if needed) Press to save.

STEP 2— Setting Meal

Step 2.1
Press   then “1” flashes to set up the first meal.

Step 2.2
Press   to set the *hour” of the time, Press   to set the “hour”. Press to move to set the” minute” of the time. Press  to save.

Step 2.3
Press to set up portion then press   button to save.
Note: Press  to modify the meal time before saving the portion if needed

Step 2.4
Press   to move to set other meals.
Repeat above step to set up meal time and portion

STEP 3— Return to Interface
Step 3.1
Press to return to interface when setting up as shown in fig.(01). (Numbers NOT displayed when portion set to 0 as shown in fig.(02))

Step 3.2
Press to modify local time, feeding time and portion if needed

STEP 4— Locking & Unlocking 

Lock:
Press   to return to interface when setting up, press for 2s to lock the screen, the lock icon will display.
(Note: Locks automatically after 2 min of inactivity)

Unlock:
Press and hold for 2s to unlock the screen, the lock icon will disappear.

STEP 5— Recording
[ Must be Unlocked ]
Hold   for 3s and start recording after a beep is heard (max 10s).
Double beep indicates recording is saved.

STEP 6— Manual Feed
[ Must be Unlocked ]
Press   to feed 1 portion

STEP 7— Reset to Factory Default
[ Must be Unlocked ]
Press and hold   and   at the same time for 3s until a beep is heard.

Scan the QR code to set up the feeder

https://qr06.cn/F3WV7X

FAQs

Q: Why the motor runs but no food comes out?

A: Please make sure the removable parts installed into the feeder correctly. For more information, please refer page 10-11

Q: Why the motor runs reversely?

A: When the food gets stuck, the motor will run reversely to solve the food stuck problem

Q: Why the feeder shows low battery but the battery is new?

A: Some rechargeable batteries have low voltages, and the feeder may give false message. Please ignore or replace ordinary non-rechargeable batteries.

Any more questions, please email our support team:

support@wopet.com

FCC WarningsFCC

• Changes or modifications to this unit not expressly approved Non-compliance could void the user’s authority to operate the equipment.

Notes:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi- cations. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which canbe determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following Measures:

• Reorient or relocate the receiving antenna.
•  Increase the distance between the equipment and receiver.
•  Connect the equipment into an outlet on a different circuit from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.Shielded interface cables must be used with the equipment in order to comply with the limits for a digital device pursuant to Sub part B of Part 15 of FCC Rules. Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer.

Warranty Information

1. NON-TRANSFERRABLE LIMITED WARRANTY
   1).To provide customers with quality shopping and user experience, we guarantee to replace or issue a refund or provide acceptable solutions to any defective products (as customer prefer) from the date of purchase to 2 years
   (2)Proof of purchase must be provided (order number or receipt) when making a claim to our customer support center.
   3)Warranty registration may be requested within a month since the date of purchase,by sending your order number to the mailbox: support@wopet.com
   (4). The warranty is not transferable We only provide warranty services to buyers who purchased from our Amazon store and WOpet official website store and possess the purchase proof, and not to any other purchaser or subsequent owner. Price matching policy is not applicable. No price difference refund.
   (5). Sellers are the responsible party, Amazon allows different sellers to sell the same product, so please confirm the seller by checking the order details before contacting us.

2.  What is Covered
   • Received defective or used (proof needed) products.
   • Received with missing parts.
   • Defective item under proper use.

3.  What is not Covered
   • Purchase from non-amazon channels/non-WOpet official website store/other physical stores
   • Gift without proof of purchase;
   • Tampering/abnormal use/accidental damage.
   • Replacements and parts.
   • Installation fee/labor fee

4. Making a claim
   If you have any problems when using our products, you can choose any of the methods to reach out of us.
   • Email: support@wopet.com
   • 30 days free Return & Replacement
   • Standard Warranty: 1-Year product Warranty
   • 2-Year Warranty Application: Please scan the QR code below to finish the registration form on our official website to get 2-Year in total warranty.
   Note:
   Please finish the form within 30 days after you received the items.

https://qr06.cn/FZDfaP

Have a Question For the Seller

• Gifted parts,replacements,consumable products are not covered by the 2-year warranty
• Manufactures’ warranties may not apply in all cases,de-pending on factors such as use of the product,where the product was purchased,or who you purchase the product from.
• Please review the warranty cafefully,and contact the manufacture if you have any questions.

https://qr06.cn/DFmMHD Boundless love for pet

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>