sunmi P2 Lite SE Handheld Scanner POS Terminal User Guide
- June 3, 2024
- SUnmI
Table of Contents
sunmi P2 Lite SE Handheld Scanner POS Terminal
DESCRIPTION
-
Magnetic card reader
Used for reading the information stored in the magnetic stripe of a bank card. -
Front-facing camera (optional)
Supports photographing and 1D/2D code quick scanning. -
Type-C USB
Used for charging equipment and debugging by developers. -
Power button
Short press: wake up the screen, lock the screen.
Long press: long press for 2-3 seconds in power off mode to switch on the device. Long press for 2-3 seconds in normal operation mode to select power off or reboot. Long press for 11 seconds when system is frozen for automatic reboot. -
Function Key(optional)
Can be configured as barcode scan keys, volume keys, or other functions -
PSAM card slot
Used for inserting the PSAM Card. -
Pogo pin
To connect to dock.(Need to buy dock separately) -
IC Card socket
Used for inserting the bank chip card. -
Two-dimensional code scanner(optional)
Used to read commodity code and mobile payment code.
Attention: do not look directly into the eyes. -
Rear camera
Supports photographing and 1D/2D code quick scanning. -
Nano-SIM Card Slot / Micro-SD Card Slot
Supports 1 Nano-SIM card plus 1 Micro-SD card, or 2 Nano-SIM cards at the same time. -
NFC reader
Used for sensing Quick Pass Card.
Notices
Safety Warning
Connect the AC plug to the AC socket corresponding to the marked input of the
power adapter; To avoid injury, unauthorized persons shall not open the power
adapter; This is a Class A product. This product may cause radio interference
in living environments. In that case, the user may be required to take
adequate measures against interference. Do not open the device in a hazardous
location.
Battery replacement:
- Explosion danger may arise if replaced with the wrong battery!
- The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into the fire!
Significant Safety Instructions
Do not install or use the device during lightning storms to avoid the
potential risks of lightning shock; Please turn off the power immediately if
you notice abnormal odor, heat, or smoke; The paper cutter is sharp, please do
not touch it!
Suggestions
Do not use the terminal near water or moisture to prevent liquid from falling
into the terminal; Do not use the terminal in extremely cold or hot
environments, such as near flames or lit cigarettes; Do not drop, throw or
bend the device; Use the terminal in a clean and dust-free environment if
possible to prevent small items from falling into the terminal; Please do not
use the terminal near medical equipment without permission.
Statements
The Company does not assume responsibility for the following actions: Damages
caused by use and maintenance without complying with the conditions specified
in this guide; The Company will not assume any responsibilities for the
damages or problems caused by optional items or consumables (rather than the
initial products or approved products of the Company). The customer is not
entitled to change or modify the product without our consent. The product’s
operating system supports official system updates, but if you change the
operating system into a third-party ROM system or alter the system files by
system cracking, it may cause system instability and security risks and
threats.
Disclaimer
As a result of product upgrading, some details in this document may not match
the product, and the actual product shall govern. The Company reserves the
right of interpret of this document. The Company also reserves the right to
alter this specification without prior notice.
Warning Signs
Warning: Only T6810 battery can be used, manufacturer: Shanghai Sunmi
Technology Co., Ltd.
Warning: Do not replace the battery when an explosive atmosphere is
present.
Warning: Do not charge the battery in a hazardous location.
Technical specifications
PRODUCT SAFETY WARNINGS
To prevent possible injury, please read all instructions and safety
information before you use the product.
- Operating temperature: -10℃ ~ 50 ℃,
- Storage temperature: -20 ℃ ~ 60 ℃.
Battery Safety
Charge the battery only at ambient temperatures ranging from 0°C to 45°C.
- CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions.
- CAUTION: Risk of explosion if battery is replaced by an incorrect type.
The product information listed on this page may be updated from time to time due to product upgrades or other reasons.SUNMI reserves the right to modify the product information and contents on this page without notice.
RF Exposure Statement (SAR)
This device has been tested and meets EU, FCC and IC RSS-102 applicable limits for radio frequency (RF) exposure. Please visit www.sunmi.com. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg for body&Head and 4W/kg for extremities averaging over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. The minimum separation distance for body-wom accessories is 10mm, the minimum separation distance for Extremities is 0mm.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED Canada compliance statements
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
EU regulatory conformance
Conformity CE
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in
compliance with the essential requirements and other relevant provisions of
Radio Equipment Directive 2014/53/EU.The full text of the EU declaration of
conformity is available at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480
INFORMATION ABOUT THE SOFTWARE
The description of accessories and components, including software, which allow
the radio equipment to operate as intended, can be obtained in the full text
of the EU declaration of conformity at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480
RESTRICTIONS OF USE
5150-5350MHz only be used by indoors.
EU Representative: SUNMI France SAS 186, avenue Thiers,69006 Lyon, France This symbol means that it is forbidden to dispose of the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authorized representative for detailed information on WEEE recycling.
External power supply:
Charger your device with the TPA-46050200VU (EU plug) and TPA-46050100VU (EU
plug) and TPA-05A050200BU01（UK plug）hat supplied by SHENZHEN TIANJIN
ELECTRONICS CO., LTD. and UC13EU (EU plug) , UC11EU (EU plug) and UC13UK（UK
plug） that supplied by Jiangsu Chenyang Electron Co., Ltd.
Manufacture
Shanghai Sunmi Technology Co., Ltd. Room 505, No.388 Song Hu Road, Yang Pu
District, Shanghai, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>