Sunmi T3 PRO Max Third Generation Desktop User Guide
- June 1, 2024
- SUnmI
Table of Contents
Sunmi T3 PRO Max Third Generation Desktop User Guide
Power On
1. Connect to the power supply
Plug the power adapter into the power port at the bottom of terminal.
Connect the other end of the adapter to the AC power socket.
2、Press the power button to turn on the screen and enter into the boot interface, then you can operate in accordance with the guidance.
Press the button to boot up the device when it is off.
Press and hold the button for 2-3 seconds to power off or reboot the device
when it is on.
Press and hold the button for 11 seconds to power off the device when it
crashes.
Install the Paper Roll
1. Open the printer cover
Press the printer cover button to open the cover
2. Load the paper roll
Load a paper roll (80mm thermal paper) into the printer but keep the paper end
out of the printer, and close the cover.
Network Setting
Wi-Fi setting
· Click “Setting” button, and then enable WLAN, enter WLAN search interface to
wait for its searching and listing available WLAN hotspots;
· Click WLAN to be connected. If an encrypted network is selected, you are
required to enter the access password to get connected.
Connect a Customer Display
A. Connect with a USB Type-C cable.
B. Insert the display according to thedirection shown.
NFC
- NFC function (optional)
Main display right side
Main display right side (rotated)
15.6” customer display right side (optional)
10.1” customer display right side (optional)
Optional Functions
Common Problems & Troubleshooting
Points for Attention
Safety Warning
- Please insert the AC plug into the AC socket corresponding to the input voltage of the power adapter;
- It is strictly forbidden to use it at a site with the existence of any potential explosive gas;
- Non-professionals are not allowed to tear down the power adapter to avoid dangers;
- This is a Class A product, which may cause radio interference in a living environment. Thus, the user may be required to carry out feasible measures against the interference.
Important Safety Instructions
- Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
- When you have discovered unusual odor, overheat or smoke, please cut off the power supply at once!
Suggestions
- Do not use it near water or in humid environment to avoid fluid to fall into the terminal;
- Do not use it in extreme cold or hot environment. For example: near an ignition source or a lighted cigarette;
- Do not drop, throw or bend the device;
- Do not use the device near medical facilities without permission.
Declaration
SUNMI will not assume responsibilities for the results of the following actions:
- Damages caused by use and maintenance without complying with the conditions specified in this user guide;
- Damages or problems caused by using optional items or consumables that are not the initial products provided or approved by SUNMI;
- The operating system of this product only supports official system updates. If the user uses a third party ROM system to update the device or modifies the system files by cracking, it may lead to system instability and may bring safety risks and threats.
Disclaimer
Due to product update, certain details of this document may be inconsistent with the product, and the real device shall prevail. SUNMI owns the interpretative right of this document, and reserves the right to modify this user guide without prior notice.
App/Software
Use the POS terminal to accept payments from customers in supermarkets,
shopping malls, department stores, convenience stores or restaurants, etc.
You can connect the terminal to a network and open the App Store to get
relevant apps.
How to check app details: select “Setting->App” and select the app name to
check its details; How to uninstall apps: select “Setting->App->Manage App” to
uninstall an app, or you can drag the app to the trash to uninstall it.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance statement
Operation of transmitter is in the 5925-7125MHz band is prohibited for control
of or communications with unmanned aircraft systems and is restricted to
indoor usage only.
Operation of device is prohibited on oil platforms, cars, trans, boats and aircraft except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
RF Soft restrictions for UNII 5/6/7/8
The device will only associate and connect with a low-power indoor access
point or subordinate device and never directly connect to other client
devices.
This device will always initiate transmission under the control of a low-power
indoor AP or subordinate except for brief transmissions before joining a
network. These short messages will only occur if the client has detected an
indoor AP or subordinate operating on a channel. These brief messages will
have a time-out mechanism such that if it does not receive a response from an
AP it will not continually repeat the request.
Transmissions will be lower or equal to the power advertised by the indoor low-power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD.
ISED Canada compliance statements
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Statements for UNII 5/6/7/8
Operation of transmitter is in the 5925-7125MHz band is prohibited for control of or communications with unmanned aircraft systems and is restricted to indoor usage only.
This device will automatically stop transmitting if there is an absence of
information to transmit or an operational failure.
The device will only associate and connect with a low-power indoor access
point or subordinate device and never directly connect to another standard
client device or low-power client device.
This device will always initiate transmission under the control of a low-power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request.
EU regulatory conformance
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that This device complies with the basic recommendations and other relevant measures in the 2014/30/EU and 2014/35/EU directive.The full text of the EU declaration of conformity is available at the following internet address： https://developer.sunmi.com/docs/read/en-US/maaeghjk480.
INFORMATION ABOUT THE SOFTWARE
The description of accessories and components, including software, which allow
the radio equipment to operate as intended, can be obtained in the full text
of the EU declaration of conformity at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480.
RESTRICTIONS OF USE
This product may be used in the following European member states subject to
the following restrictions. For products that operate in the frequency band
5.150 to 5.350 GHz and 5945-6425MHz, wireless access systems (WAS), including
radio local area networks (RLANs), shall be restricted to indoor use.
EU Representative :SUNMI France SAS
186,avenue Thiers,69006 Lyon,France
This symbol means that it is forbidden to dispose the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling.
RF Exposure Statement (SAR)
- This equipment complies with EU, FCC and IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Energy Start® certification
The device will be automatically switched in 5 mins display sleep(default)，in
30mins device sleep(default)if there is no any operation.
The time of auto screen off can be change in the setting menu。
Auto screen off (default 5mins) and auto sleep(30mins)have been selected for
compliance with ENERGY STAR®, And are recommended by the ENERGY STAR® program
for optimal energy savings。
Manufacturer: Shanghai Sunmi Technology Co., Ltd.
Address:Room 505,No.388,Song Hu Road,Yang Pu District,Shanghai,China
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>