SUNMI BL204 Electronic Shelf Label User Manual

SUNMI Technology
User Manual of SUNMI Electronic Shelf Label (ESL)

Revision History

Issued Date| Revised Contents|

Version

---|---|---
2019-07-28| Draft| V1.0
2019-09-15| English version| V1.1
2020-06-19| And some attention| V1.2
| |

FCC Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Preliminary Work

Before implementing a formal deployment, the following preparations need to be completed:

1. Business cooperation process;
2. Statistics on the number and type of store ESLs;
3. Statistics on the installation mode of store ESLs (the type and quantity of guide rails and clamps);
4. Location determination of the access point installation (focus on the network wiring);
5. Cloud deployment mode confirmation (SaaS or private cloud).

For the specific preparation process, please see the implementation preparation collected in the separate project documentation.

Product docking

It is necessary to start the docking of product information as soon as possible, after the confirmation of the business contract and the confirmation of product docking demand.
It takes about two weeks for product information docking.
The general process of product information docking is as follows:

1. SUNMI, the software partner shall discuss docking requirements and release technical documents;
2. Confirm the docking plan and schedule the project;
3. Developing docking interface and launching after multiple environmental tests.

The deployment and implementation of equipment shall start after product docking. See separate product docking documents for specific product docking procedures and instructions.

Equipment Installation

3.1 Installation Preparation
Tools to be carried with during installation:

1. Rags, used to clean shelves
2. Big scissors or cutting machines for cutting guide rails
3. Electric drill for fixing equipment

3.2 Access Point
3.2.1 Introduction
The access point (AP) for SUNMI smart ESLs is used to connect ESL equipment with SUNMI digital store. The image and the instruction emitted by the digital store server are transmitted to the wireless access point through the Ethernet and the access point is further distributed to the ESL through the wireless communication of the 2.4 G frequency band so that the cloud changes price and the ESL refresh can be realized. The following table shows the basic specifications of the wireless access point for smart ESLs:

The relevant interface description on the wireless access point for smart ESLs is as follows:

| Ports|

Description

---|---|---
1| Power light| • White flicker: during access point startup
• Normally White ON: access point is connected to the server and is working properly
• Normally Red ON: access point cannot connect to the server
2| Reset button| Press for 5 seconds to restore the access point to the factory state
---|---|---
3| Internet port| RJ45 Ethernet port with indicator light, support for PoE power supply
4| Power port| Power adapter port to support independent power supply
5| Installation hooks| Bring its own detachable hooks so that the access point supports a variety of installation methods

3.2.2 Base Installation
3.2.2.1 Power Supply Mode
SUNMI wireless access point for smart ESLs supports power adapter and PoE power supply, which power supply mode needs to be determined by in-store environment and installation mode. The power adapter line is 2 meters long. Use the plug board if it is not long enough, while strictly forbid to extend the power cord by yourself.
The installation of the access point adopts ceiling and hanging-wall styles, but when the power cord of the adapter is not long enough, PoE can be used to power the access point. PoE power supply needs to apply a separate PoE module or PoE switch, and the network line connected by PoE module / switch can be plugged directly into the access point to supply power to the access point.
Note: it is strictly forbidden to use both power adapter and PoE power supply at the same time.

3.2.2.2 Internet Access
SUNMI access point for smart ESLs supports DHCP and static IP.
If it is only a single access point, ensure that the access point can connect to the cloud server or the local server.
If there is more than one access point, it is necessary to let each access point be located under the same LAN in order to realize the network roaming of access points and labels.
3.2.2.3 Installation and Fixation
The fixation of ESL access points supports ceiling, hanging walls, and desktop placement. It is recommended to install it on the ceiling, which can get wider signal coverage; Wall hanging and desktop placement are only suitable for the cases where the labels are less or close to the access point.
For ceiling installation, the installation height is recommended as 3~3.5 meters (can be adjusted by a metal universal rod). Max coverage radius of a single access point is 25 meters (laboratory test results), and 15 meters is recommended.

If multiple access points are needed, it is necessary to ensure that each access point signal has an overlapping area and that each label is at least within the coverage of more than one access point. If there are walls, columns, air pipes, refrigerators, etc., between the access point and the label, the wireless signal will be affected and attenuated to a certain extent. When the access point is installed, it should avoid the above objects as far as possible. If it cannot be avoided, it can be regarded as reducing the coverage radius of the access point.
The signal frequency band of the ESL access point coincides with the band of 2.4G Wi-Fi. If the ESL access point and the wireless router are installed together, the two will interfere with each other, so the two should be installed separately.
Actually, when installing the access point, we also need to consider the number of ESLs that the access point can support. Single SUNMI wireless access point for smart ESLs supports a maximum of 10000 pieces of ESLs. But considering the refresh speed of batch push and system redundancy, it is recommended that one access point be allocated for every 3000 pieces of labels. The installation distance between access points can be adjusted accordingly.

3.2.3 Access Point Configuration
After all ESL access points are installed, it is necessary to use SUNMI assistant APP to configure each access point, including the Internet access mode and name of each access point. After configuration, the tie-up between the access point and store will be completed to realize the networking of the access point, so that the labels can be connected to the access point. Detailed configuration refers to the implementation process documentation of software operations.

3.3 ESLs and Accessories
The label cannot be installed independently, it needs to be installed with various types of accessories to the shelf, basket rack and pile head.

3.3.1 Attention

1. Avoid heat and fire.
2. Recommanded long-term(over 3 months) storage condition is dry and cool.
3. Please use the special battery pack provided by the dealer.
4. When replace the battery, please contact the after-sales service and get instructions.

Software Operation

Software configuration and usage include operations on the SUNMI digital store website and on the SUNMI ESL APP of PDA.
In SUNMI digital store, you need to complete:

1. Register an account in SUNMI digital store;
2. Set up docking of product information;
3. Design template for ESL;

On the SUNMI ESL APP of PDA, you need to complete:

1. Configure the Internet access mode of the AP;
2. Bind ESL and product;
3. Unbind ESL and product;
4. Search product.

Check below for specific procedures.

4.1 SUNMI digital store
The operations of SUNMI digital store need to be complete before the deployment of equipment installation.
4.1.1 Register an account in SUNMI digital store
Visit the website store.sunmi.com through Chrome, Firefox, QQ browser, and 360 browsers on a computer to register an account. If already registered, step over to sign in.
Create the company and store after sign-in. Step over if the account has already been created.

4.1.2 Set up docking of product information
Enter into [Basic data > Product management] from menu on the page left, and you can see the product list, and all products with bindable ESLs are listed here.
In the prior test or trial, you can input information and create a product manually, or modify product information manually.
In the formal usage, product library is generally necessary to dock with ERP/POS software to realize auto-import, revise and delete.

Enter the [Docking ERP] function, select the ERP platform that has been docked in the previous work, and input the authentication information (which can be obtained on the page under some part of the ERP software, and some other part needs to be obtained by the ERP manufacturer).
The storage can complete the docking of the product library and start drawing the products. After setting up ERP docking, the product library of the digital store will get all the product information from the ERP through the API interface, and it will synchronize to the SUNMI digital store after each modification in ERP, and then synchronize to the ESL.

4.1.3 Template design
Template is to present product information for ESL. Users can present through user-defined functions.
Enter [ESL > Template Management], you can edit existing templates, or create new templates for design.
Templates are classified according to size and color. an ESL of a certain size can only use a template of that size, a constant temperature ESL can use black and white red, black and white templates, and a low-temperature ESL can only use black and white templates. Suggest completing the validation of the template in advance.

4.2 SUNMI ESL APP
The operations of the SUNMI ESL APP are under equipment deployment.
Please acquire SUNMI ESL APP in SUNMI APP Store, and the APP is functioning in SUNMI L2 only.
4.2.1 Access point configuration
The access point configuration shall be carried out before ESL installation when the access point installation is completed, to make all ESLs easily connect access points successfully at the time of ESL binding.
After completing the installation of the access point, energize it, insert the cable, then wait for the light is normally white or red. At this time, you can add a configuration access point by using the SUNMI ESL APP on L2. The concrete steps shall be as follows:

1. Start the SUNMI ESL APP, and sign in with the account of SUNMI digital store.

2. Go to the APP system page, click [AP management > Add AP], then start searching for the access point signal with l2.
   In order to ensure that the signal strength of the access point is strong enough to be connected by L2, it is necessary to search as close as possible to the access point.

3. Select the access point that needs to be added (according to the signal strength or MAC address, the scanned MAC address is the same as the MAC address on the bottom nameplate of the access point) to enter the process of the access point adding and configuring.
   First of all, you need to set up the access point Internet access mode, you can choose to automatically obtain IP (DHCP) or manually input IP (static IP). The automatic acquisition of IP (DHCP) mode can be used generally.
   After setting the Internet access mode, set the access point name (required), and click confirm add to add the access point to the current store to complete the binding.

When the access point configuration is completed, the added access point will be seen in the access point list, and if the access point status is online, it is in normal operation. If the access point is offline, please check the connection status of the power supply and the network, and try to reconfigure the access point access mode.
For the added access point, you can choose to manage in the access point list, modify the access point name, delete the access point, or modify the access point access mode.
To modify the access point access mode, you need to reconnect the access point, please approach the access point and operate it again. The modification is the same as access point adding.

4.2.2 ESL and product binding
After the ESL is installed, you can start binding the ESL to the products.
Enter the binding page from the APP home page: select ESL, select template, select product, and complete binding.
[Select ESL] can be achieved through the bar code on the L2 ESL (the bar code is the unique identified ID), or through NFC by closing L2 to the ESL to obtain the ID.
SUNMI ESL supports NFC, which can obtain the ESL ID through NFC on the PDA, or reset the ESL device.
[Select Template] is to choose the designed template in SUNMI digital store previously.
[Select Product] can be realized directly by scanning the product bar code. If there is no bar
code, you can enter the product number/name/bar code to select the product.
After selecting the product, template and ESL, click on “Bind” to bind the product with the ESL, and jump to the ESL selection page to facilitate the rapid binding of the next ESL with the product.
Under normal circumstances, within half a minute of binding completion, the ESL will refresh and display the product information with the selected template.

After completing the binding of all products and ESL, return to the home page of the SUNMI ESL APP. When the number of ESLs to be pushed becomes 0, that means all the ESLs are completed and the ESL system is deployed for the first time.
If it is any modification in need later, directly modify in the ERP, then the product information will be immediately synchronized to the SUNMI digital store and sent to the ESL.
If the products move location and no longer correspond to the ESL, you need to rebind or unbind directly according to the above process.
4.2.3 ESL unbinding
If you do not want an ESL to display product information, you can unbind the ESL, THEN the ESL will display the factory default picture.
Unbind method is similar to binding, using code sweeping or NFC to select the ESL, and click unbind to complete work.

4.2.4 Product inquiry
Inquire through the product number/name/bar code and the bar code of the product binding ESL.
Enter the product details page to see the product information, as well as the ESL bound to the product, click on the flash lamp to allow the ESL to flash immediately.

Version: V1.2
Jun. 19, 2020

Documents / Resources

| SUNMI BL204 Electronic Shelf Label [pdf] User Manual
BL204, 2AH25BL204, BL204 Electronic Shelf Label, Electronic Shelf Label, Shelf Label
---|---
| sunmi BL204 Electronic Shelf Label [pdf] User Manual
BL204, 2AH25BL204, BL204 Electronic Shelf Label, Electronic Shelf Label

References

• SUNMI STORE
• SUNMI STORE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>