sunmi P2 SE Payment Terminal User Guide

: June 5, 2024
: SUnmI

Table of Contents

Quick start
Printing instructions
Technical speciﬁcations
ISED Canada compliance statements
Documents / Resources

QUICK START GUIDE
T 682 0

|
---|---

US(Canada) : dual SIM
EU : Fngerprint – signle SIM / Scanner – dual SIM

Quick start

NFC reader
Used for sensing Quick Pass Card.
Magnetic card reader
Used for reading the information stored in the magnetic stripe of a bank card.
Scan Button (optional)
Short press to scan barcode.
Type-C USB
Used for charging equipment and debugging by developers. Do not charge the battery in a hazardous location.
Function Button
Used for customized function.
Power button
Short press: wake up the screen, lock the screen.
Long press: long press for 2-3 seconds in power oﬀ mode to switch on the device.
Long press for 2-3 seconds in normal operation mode to select power oﬀ or reboot.
Long press for 11 seconds when the system is frozen for an automatic reboot.
Printer
For printing, sales slips in power on mode.
IC Card Reader
Used for reading chip card
Scanner (optional)
Used for accurate data capture.
Note: laser radiation. Do not stare into beam！
Rear camera
Supports photographing and 1D/2D code quick scanning.
Extend pins
To connect to dock. (Need to buy dock separately) Do not use dock in hazardous locations.
Slide down the metal buckle and take out the Nano SIM
PSAM card slot (SIM card optional)
Open the back cover, take out the battery and insert the PSAM card (SIM card optional).
P-SAM card slot
Open the back cover, take out the battery and insert the PSAM card.
Micro SD card slot
Open the back cover, take out the battery and insert the extended SD card.
Nano SIM card slot
Used for inserting Nano SIM card.

Printing instructions

This device supports 58mm thermal paper with the speciﬁcations of 57±0.5mm*Ø40mm.
① Please open the paper container with the uncovering handle， Please do not force open the paper container to avoid print head gear wear;
② Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter;
③ Close the cover of the paper container to ﬁnish printing paper feeding.
Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.
Do not open paper container when an explosive atmosphere is present.

Notices

Safety Warning
Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;
To avoid injury, unauthorized persons shall not open the power adapter;
This is a Class A product. This product may cause radio interference in living environments.
In that case, the user may be required to take adequate measures against interference.
Do not open the device in a hazardous location.
Battery replacement:

Explosion danger may arise if replaced with the wrong battery!
The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into ﬁre! This device is anti-explosion product with Ex ic IIC T6 Gc level.

Signiﬁcant Safety Instructions
Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
Please turn oﬀ the power immediately if you notice an abnormal odor, heat, or smoke;
The paper cutter is sharp, please do not touch it!

Suggestions

Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;
Do not use the terminal in extremely cold or hot environments, such as near ﬂames or lit cigarettes;
Do not drop, throw or bend the device;
Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;
Please do not use the terminal near medical equipment without permission.

Statements
The Company does not assume responsibilities for the following actions:
Damages caused by use and maintenance without complying with the conditions speciﬁed in this guide;
The Company will not assume any responsibilities for the damages or problems caused by optional items or consumables (rather than the initial products or approved products of the Company). The customer is not entitled to change or modify the product without our consent.
The product’s operating system supports oﬃcial system updates, but if you change the operating system into a third-party ROM system or alter the system ﬁles by system cracking, it may cause system instability and security risks and threats.

Disclaimer
As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern.
The Company reserves the right of interpreting this document. The Company also reserves the right toalter this speciﬁcation without prior notice.
Warning Signs
Warning: Only T6820 battery can be used, manufacturer:
Shanghai Sunmi Technology Co., Ltd.
Warning: Do not replace the battery when an explosive atmosphere is present.
Warning: Do not charge the battery in hazardous location.
Caution：Risk Group 2.Possibly hazardous optical radiation emitted from this product. Don’t stare at operating lamp. May be harmful to the eyes.

External power supply:
Charger your device with the TPA-46050200VU (EU plug) and TPA-46050100VU (EU plug) supplied by SHENZHEN TIANYIN ELECTRONICS CO., LTD. and UC13EU (EU plug) that supplied by Jiangsu Chenyang Electron Co., Ltd.

Technical speciﬁcations

PRODUCT SAFETY WARNINGS
To prevent possible injury, please read all instructions and safety information before you use the product.
Operating temperature: -10℃ ~ 50 ℃,
Charging temperature: 0℃ ~ 40℃,
Storage temperature: -20 ℃ ~ 60 ℃.

Battery safety
Charge battery only at ambient temperatures ranging from 0°C to 45°C.
(1) CAUTION: Danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type of battery recommended by the manufacturer.
Dispose of used batteries according to the battery manufacturer’s instructions.
(2) CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

The product information listed on this page may be updated from time to time due to product upgrades or other reasons.SUNMI reserves the right to modify the product information and contents on this page without notice.
Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin /button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

RF Exposure Statement (SAR)
This device has been tested and meets EU, FCC, and IC RSS-102 applicable limits for radio frequency (RF) exposure.
Please visit: www.sunmi.com.

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: The user is cautioned that changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED Canada compliance statements

This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

EU regulatory conformance

Conformity CE
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of
Radio Equipment Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480

INFORMATION ABOUT THE SOFTWARE
The description of accessories and components, including software, which allows the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480

RESTRICTIONS OF USE
5150-5350MHz only be used by indoor.

| AT| BE| BG| CY| CZ| DE| DK| EE| ES| Fl| FR
---|---|---|---|---|---|---|---|---|---|---|---
GR| HU| IE| IT| LT| LU| LV| MT| NL| PL| PT
RO| SE| SI| SK| UK
(IN)| | | | | |

EU Representative :SUNMI France SAS 186,avenue Thiers,69006 Lyon,France
This symbol means that it is forbidden to dispose of the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authorized representative for detailed information on WEEE recycling.

Manufacture
Shanghai Sunmi Technology Co., Ltd.
Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District,
Shanghai, China

M05054268