sunmi L1583 POS System User Guide

sunmi L1583 POS System

Three Configuration Option

Easy Setup

Get the device ready for use in a few steps.

1. Press the power button to turn on the screen and enter into the boot interface, then operate following the onscreen instructions.
   Two network modes can be selected for this device.

2. Wi-Fi Setting

   • Click the button [Setting], and enable WLAN to enter into the interface for Wi-Fi searching. Wait for the available Wi-Fi list;
   • Click the Wi-Fi to be connected, and a password is required if you want to connect to an encrypted network.

3. LAN Setting

How to Download/Use Apps
With a network connection, you can download and install apps you need from the App Store.

List of System Preset Software

• App Store · Instruction · Pos Steward · Feedback · Remote Assistance
• Gallery · Downloads · Calculator · System Update · ShopCenter

Note: the preset software list is subject to change due to software updates. For more help, please refer to the Instruction App in the device.

Package Items List

• Quick start guide × 1
• Power adapter × 1
• Smart terminal × 1
• Printing paper roll × 1

Product Overview

“Take the facial recognition version as an example”

Power button

• Press the button to boot up the device when it is off;
• Press and hold the button for 2-3 seconds to power off or reboot the device when it is on;
• Press and hold the button for 11 seconds to power off the device when it crashes.

Touch Screen

A touch screen for operators to use.

Facial Recognition Camer

Three options: monocular/binocular/3D structured light camera.

Device Installation

1. Open the printer cover
   As shown in the figure, press the button at the bottom left corner to pop open the printer cover.

2. Install the printing pape
   Load the 58mm thermal paper and pull out a section outside the cutter, then close the cover.

3. Connect the power cable
   Connect the power adapter to the power port on the back of the display. Plug the other end of the power adapter into the mains socket.

Troubleshooting

Device crashes

| · Press and hold the power button for 11 seconds to power off the device, then press to reboot.

The printer doesn’t work

| · Check whether the printer cover is closed properly;

· Check whether there is a paper jam.

The printer prints blank pages

| · Check whether the paper roll is placed reversely;

· Check whether the 58mm thermal printing paper roll is used.

Blurry printouts

| · Check whether the thermal head is dirty. If it is dirty, please wipe it with a cotton swab dipped in absolute alcohol;

· Replace the thermal paper with guaranteed quality to avoid blurry printouts

caused by paper.

The paper does not come out| · Check whether there is a paper jam. Open the cover, check the paper feeding channel and clear the paper jam if there is one. C

Note:
When cleaning the thermal head or paper feeding rubber roller, do not scratch the thermal head and rubber roller with hard objects (such as tweezers);
In order to improve the service life, it is recommended to clean the thermal head and rubber roller every month. When cleaning, please use a cotton swab dipped in absolute alcohol to gently wipe the thermal head.
For more information, please visit: www.sunmi.com or call at: 400-6666-509.

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:
The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Attention

Safety Warnings

• · Please insert the AC plug into the AC socket corresponding to the input marked on the power adapter;
  · Please use the device within the temperature range of 0 °C ~ 40 °C, and store the device and accessories within the range of – 20 °C ~ 60 °C;
  · It is strictly prohibited to use the device in places with any potentially explosive gas;
  · Non-professional personnel shall not open the power adapter at will to avoid danger;
  · This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take appropriate measures.
  · Battery replacement:

  1. 1. There is a risk of explosion if the battery of the wrong model is used!
     2. The replaced old battery should be handed over to the maintenance personnel for disposal. Do not throw it into the fire!

Important Safety Instructions

• · Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
  · Cut off the power immediately when you find a suspicious smell, overheating or smoke!

Suggestions

• · Do not use the device near water or in a damp environment to prevent liquid from getting inside the device;
  · Do not use the device in extremely cold and hot environments, such as near fire sources or lit cigarettes;
  · Do not drop, throw or bend the device;
  · Use the device in a clean and dust-free environment to prevent small items from falling into the device;
  · Do not use the device near medical facilities without permission.

Declaration

The Company does not assume responsibilities for the following actions:

• · Damages caused by use and maintenance without complying with the conditions specified in this guide;
  · Damages or problems caused by optional items or consumables that are not the initial products or approved products of the Company.
  · Modification or changing of the product without the permission of our company is not allowed;
  · The operating system of this product supports official system updates. If users use a third-party ROM system to update the device or modify the system files by cracking, it may lead to system instability and may bring safety risks and threats.

Disclaimer

Due to the update of the product, some details of this document may be inconsistent with the product, and the actual product shall prevail. Our company reserves the right to interpret this guide as well as amend it without prior notice.

ISED Canada compliance statements

This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

EU regulatory conformance

Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaegh-jk480.

INFORMATION ABOUT THE SOFTWARE

The description of accessories and components, including software, which allows the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480.

Manufacturer: Shanghai Sunmi Technology Co., Ltd.
Address: Room 505, Building 7, KIC, 388 Songhu Road, Yangpu District, Shanghai, PR China.

References

• SUNMI - BIoT for Business 4.0
• developer.sunmi.com/docs/read/en-US/maaegh-
• developer.sunmi.com/docs/read/en-US/maaeghjk480

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>