AMP Lighting AFL-40XX-LI-B-BZ Line Voltage 120V Landscape Lighting Installation Guide
- June 6, 2024
- AMP Lighting
Table of Contents
- AMP Lighting AFL-40XX-LI-B-BZ Line Voltage 120V Landscape Lighting
- Important: Please Read Before Installation
- Important Safety Instructions
- Product Dimensions
- Option 1: Surface Mount
- Option 2: Stake Mount
- Wire Connection
- Adjust Fixture Body Direction
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AMP Lighting AFL-40XX-LI-B-BZ Line Voltage 120V Landscape Lighting
Important: Please Read Before Installation
- This LED floodlight uses the latest in solid state lighting technology for long life, low maintenance, and high efficeiency.
- An internal power-factor-corrected switch mode supply allows this fix-ture to be used from any nominal 90V-277VAC, 60Hz supply without any variation in light output.
- Suitable for use in:
A. Ambient Temperatures of: -20~+45°C (-4~+113°F)
A. Wet Locations
Note : Save these instructions for future reference.
Important Safety Instructions
To avoid the risk of fire, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualified electrician only, in
accor-dance with all applicable electrical codes.
To avoid electric shock:
- Be certain electrical power is OFF before and during installation and maintenance.
- Luminaire must be connected to a wiring system with an equip-ment-grounding conductor.
To avoid explosion:
- Make sure the supply voltage is the same as the rated luminaire voltage.
- Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.
- Do not operate in ambient temperatures above those indicated on the luminaire.
For supply connections use wire rated for at least 90°C (194°F)
Warning: These luminaires should ONLY be installed by a qualified
electrician.
Package Contents
A. (1) Fixture body
Parts Required
A. (1) Mounting Accessory (Sold Separately)
Products Model #
Model | Input Voltage | Hertz | Input Cur- rent | Watt |
---|
9W Flood Light
|
90-277
|
60
|
0.2
|
9
17W Flood Light
|
90-277
|
60
|
0.4
|
17
Product Dimensions
120VAC 17W
Two installation methods are provided for this fixture: Surface Mount- Page 5
Stake Mount- Page 6
Install Surface Mount to Fixture body
Glare Guard Pass the supply cable through the center hole of the surface mount. Then thread the surface mount onto the fixture body. Make sure the wire exit on the surface mount and the glare guard are facing the opposite direction after installation.
Option 1: Surface Mount
Install Fixture Body to Surface
Place the supply cable in the wire exit. Then attach the surface mount with
the fixture body to the mounting surface and secure with self-tap-ping screws
using a screwdriver to tighten.
NOTE: Wall anchors are required for brick walls or concrete walls. To
determine anchor locations, place the surface mount onto your de-sired
location and mark points using the hole on the surface mount as a guide.
Go to Step 3 – Step 4 for wiring connections and direction adjustments.
Option 2: Stake Mount
1 Install Stake
Determine the desired location for mounting the stake. Hammer the stake into
the ground until flange of stake is flush to grade. To avoid damage to the
stake, place a board on top of the stake while hammering.
Note: If the ground is hard and the stake is difficult to install, make a
crosscut in the ground using a flat shovel.
2 Install Fixture Body to Stake
Pass the supply wires through the center hole of the stake and thread the
fixture body onto the stake. Hand tight-en until snug. Clear away an area in
the ground and lay the supply wires into the stake’s wire exit.
Go to Step 3 – Step 4 for wiring connections and direction adjustment.
Wire Connection
By using the Allen wrench, loosen screws and remove the cover from the hub
body.
Insert the main supply cable, fixture supply cable, other fixture supply cable
or next hub supply cable into the hub body from the different conduit. Strip
both ends of all cables. Lift the clamps up and insert the ends of neutral
wires into the “NEUTRAL” block. Insert the ends of live wires into the “HOT”
block. Insert the ends of ground wires into the “GROUND” block. ensure that
each wire is pushed into place securely and close the clamps.
Place the cover back onto the hub body and secure with previously removed
screws. Hand tighten until snug with Allen wrench.
Adjust Fixture Body Direction
Using the Allen wrench, loosen the screw on the knuckle and adjust the fixture body to your desired direction. Once your desired direction is achieved, tighten the knuckle down with the Allen wrench.
Help Hotline:
Specifications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@amplighting.com •
813.978.3900
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>