AMP Lighting APL-3023-4-B-BZ Stagecoach LED Path and Area Light Installation Guide

AMP Lighting APL-3023-4-B-BZ Stagecoach LED Path and Area Light

Important Safety Instructions:

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

1. Make sure that the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).

THE LIGHTED LAMP IS HOT!

WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the fixture with a damaged or missing lens or shield.

Package Contents

• (1) Fixture
• (1) Stem
• (1) Ultra Realistic LED Moving Flame Bi-Pin Candle
• (1) 17” Stake

Additional Parts Required (sold separately)

• (1) LED SCB Lamp

Product Dimensions

Remove the Hat

Remove the hat from the stem by removing the set screws from the hat mount.

Install LED Lamp

Insert the lamp with the correct wattage and type marked on the fixture label.
CAUTION: Do not exceed maximum wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare hands. Use soft cloth to handle bulb.

Reinstall Hat

After installing the LED lamp into the socket, place the hat back onto the mount at the top of the stem. Secure both pieces in place with the set screws previously removed. Hand tighten until snug.

Remove Upper Part of Hat

Remove the upper part of the hat by loosening the set screws.

Install LED Bi-Pin Candle

Insert Ultra Realistic LED Mov-ing Flame Bi-Pin Candle.
CAUTION: Do not exceed maximum wattage marked on luminaire label.

Reinstall Upper Part of Hat

Place the upper part of the hat back onto the lower part of the hat and secure with the set screws previously removed. Hand tighten until snug.

Install Stem

Pass the supply wires through the stem and extension. Then thread the exten- sion onto the stem. Hand tighten until snug.

Install Stake and Conduit

Dig a hole in the ground for the conduit runs and the stake. Install the conduit. Slide the stabilizer grid onto the stake and secure with the screws. Place the stake over the conduit runs. Backfill against the mounting stake.

Remove Cap from Stake

Remove the cap from the stake by loosening the set screws.

Install Cap to Fixture

Thread the cap onto the fixture body and hand tighten until snug.

Wire Connection and Fixture Installation

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

Specifications and product details subject to change without notice. © Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@amplighting.com • 813.978.3900

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>