AMP Lighting AAL-10XX-LI-B-BZ Low Voltage Landscape Lighting Instruction Manual

June 6, 2024
AMP Lighting

AMP Lighting AAL-10XX-LI-B-BZ Low Voltage Landscape Lighting Instruction Manual
AMP Lighting AAL-10XX-LI-B-BZ Low Voltage Landscape
Lighting

Important Safety Instructions: Read Before Installation

  1. This LED Floodlight uses the latest in solid state lighting technology for long life, low maintenance, and high efficiency.

  2. An internal power-factor-corrected switch mode supply allows this fixture to be used from any nominal 100V-277V, 50/60Hz AC supply without any variation in light output.

  3.  Suitable for use in:

    • Ambient Temperatures of
      6W & 12W: -20~+45o C (-4~+113o F)
      18W: -20~+25o C (-4~+77o F)

    • Wet Locations

  4. INSTALLATION OR ASSEMBLY INSTRUCTIONS

Note: Save these instructions for future reference.

Important Safety Instructions

To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

  1. Be certain electrical power is OFF before and during installation and
    maintenance.

  2. Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

  1. Make sure the supply voltage is the same as the rated luminaire voltage.
    • 6W
    • 12W
    • 18W
  2. Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.
  3. Do not operate in ambient temperatures above those indicated on the luminaire.

For supply connections use wire rated for at least 90°C (194°F)

Warning: these luminaire should ONLY be installed by a qualified electrician.

Package Contents

  1. (1) Fixture
  2. (1) Allen Wrench

Products Model

Model Input Voltage Power Factor Watt Input Current

6W

Spotlight

| 100-277V| ≥0.95| 6W| .1A
12W

Spotlight

| 100-277V| ≥0.95| 12W| .12A
18W

Spotlight

| 100-277V| ≥0.95| 18W| .18A

Product Dimensions

  • 6W 120V Spot Light & 12W 120V Spot Light
    Product Dimensions

  • 18W 120V Spot Light
    Product Dimensions

Install Stake and Conduit

Install Stake and Conduit

Dig a hole in the ground for the conduit runs and the stake. Install the conduit. Slide the stabilizer grid onto the stake and secure with the screws. Place the stake over the conduit runs. Backfill against the mounting stake.

Remove Cap from Stake

Remove Cap from Stake

Remove the cap from the stake by loosening the set screws.

Install Cap to Fixture

Install Cap to Fixture

Thread the cap onto the fixture body and hand tighten until snug.

Wire Connection and Fixture Installation

Wire Connection and Fixture Installation

Allow enough wire from the fixture for adjustment purposes. Connect the wires from the fixture to the 120v supply wires. The white wire goes to the “Neutral” wire; the black wire goes to the “Live” wire; and the green wire goes to the “Ground” wire. Use a UL certified wire connector for each connection.

Adjust Lamp Direction

Adjust Lamp Direction

Loosen the set screw at the joint by using the Allen wrench and adjust the fixture body to the desired direction. When the desired direction is achieved, tighten the set screw until snug.

After installation, please

  1. Double check whether the lighting fixture is firmly fixed.
  2. Double check the wires are connected correctly.

At last, turn on the power and check if the lighting fixture is working properly.

Help Hotline

1-813-978-3900 • Mon-Fri 9am-6pm (EST)

Specifications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@amplighting.com • 813.978.3900

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

AMP Lighting User Manuals

Related Manuals