Shenzhen Furrykid Technology T1SPRO Smart Training Collar User Manual

T1SPRO
User Manual

Thank you for purchasing the Dr.Trainer Smart Training Collar. We have made every attempt to provide you with the most technologically advanced product, using the most stringent quality and manufacturing standards. We are confident you will be pleased with the results you’ II attain with your Dr.Trainer. Please remember, you will get better results with the use of lower static levels combined with consistent training techniques. The use of high levels of static should only be used as a last resort, or in life-threatening situations. Good luck with your training, and please feel free to contact us, should you have any questions.
971-302-6642 or Service@DrTrainer.com

Important Safety Information

Not for use with aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or a certified trainer.
Safety during on-leash training. It is vitally important that you and your dog remain safe while learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough so he can’t reach a road or other unsafe areas. You must also be physically strong enough to restrain your dog when he tries to chase something.
Risk of skin damage. Please read and follow the instructions in this manual. The proper fit of the collar is important. A collar worn for too long or fastened too tightly on your pet’s neck may cause skin damage, ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the pet’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts. When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.

How does the Dr.Trainer Smart Training Collar work?

Now, you can experience the difference a Dr.Trainer can make. Spend less time training and more time enjoying your dog.
The Dr.Trainer is easy to use, with combined functions that you can set in advance. Then, all you need to do for training is to press the Send Button on your Remote Transmitter. It sends a signal activating your dog’s Receiver Collar. He receives a safe but annoying stimulation. He will quickly understand the association between his behavior and your correction; in no time, you’ll have a better-behaved pet. The Dr.Trainer has been proven safe, comfortable, and effective for both small and large dog breeds.
Important: The Dr.Trainer has a range of up to 750 yards. Depending on the way you hold the Remote Transmitter, the maximum range may vary. Terrain, weather, vegetation, transmission from other radio devices, and other factors will also affect the maximum range.

Operating Guide

STEP 1: Check the connection between Receiver Collar and Remote Transmitter.

1. Turn the Receiver Collar on.
2. Press the Settings button on the Remote.
3. If the Receiver’s battery icon lights up, it means the two devices are connected.
4. If the two devices are disconnected, follow Step 5 for a wireless pairing connection.

STEP 2: Test the Static Function
To ensure that the Static Function works properly before using the collar on your dog, it is recommended that you test the Static Function at least once before use. Please follow the instructions below for how to use the Test Light.

1. Turn the Receiver Collar on.
2. Place the Test Light above the Contact Points.
3. Set your combination command, making sure that at least the Static function is turned on.
4. Press Send Button on the Remote.
5. The Test Light will flash if the function is working.
6. Turn the Receiver Collar off, store the Test Light for future testing.

Note: If the test light does not flash, recharge the battery and re-test.

STEP 3: Fit the Smart Bark Collar
Important: The proper fit and placement of your Bark Collar is important for effective operation. To ensure a proper fit, please follow these steps:

1. Make sure that the Receiver Collar is turned off.
2. Start with your dog standing comfortably.
3. Place the Bark Collar on your dog’s neck close to the ears. Center the Contact Points underneath your dog’s neck.
4. Check the tightness of the Bark Collar by inserting one finger between the collar and your dog’s neck. The fit should be snug but not constricting.

Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that the contact electrodes deliver effective static.

STEP 4: Pair the Receiver Collar with your phone.

1. Open Bluetooth and the APP on your phone, and follow the instructions.
2. Turn on the collar, by pressing the Power Button for more than 1 second.
3. Quickly double-click the Power Button of the device to enter pairing mode (blue and green lights flash alternately).
4. After the device is detected by the App, please confirm the first connection manually.

STEP 5: Reconnect the Receiver Collar with your Remote Transmitter. (Only used when the connection is broken)
Note: If the two devices are disconnected, first make sure the Receiver Collar is turned on, and close to the Remote Transmitter.

1. Quickly double-click the Power Button of the device to enter pairing mode (blue and green lights flash alternately).
2. Press the Up and Down buttons at the same time on your Remote Transmitter, for more than 5 seconds to establish the connection.
3. The indicator light of the Receiver turns blue and stays on for 3 seconds, indicating a successful device connection.

FAQ’s

Q: Is the static-safe for my pet?
While the static is unpleasant, it is harmless to your pet. Electronic training devices require interaction and training from the owner to achieve desired results.
Q: How old does a pet have to be before using the Dr.Trainer?
Your pet should be able to learn basic obedience commands such as “Sir or “Stay.” Pets should be at least 6 months old before using the Trainer.
Q: Is the Receiver Collar waterproof?
Yes. All of the Dr.Trainer Receiver Collars are waterproof. Q: Can I use the Dr.Trainer on aggressive pets?
We do not recommend that any of our products to be used on aggressive pets. We recommend that you contact your local veterinarian or professional trainer to determine if your pet might be aggressive.
Q: Why my pet is not responding when I press the Send Button?

• Check to see if the Collar has been turned on.
• If your range has reduced since the most recent use, please check to see if the battery is low in either the Remote Transmitter or Receiver Collar.
• You can verify the Collar is delivering static to your pet by using the Test Light. Please refer to the “Test the Static Function” section for details.
• Increase the correction level.
• Make sure the Receiver Collar’s Contact Points are placed snugly, in contact with your pet’s skin.

Q: Why won’t the Receiver Collar turn on?
Make sure the Receiver Collar has been charged.
Q: Why is the Receiver Collar not responding to the Remote Transmitter?
Verify the Receiver Collar has been turned on. Refer to Operating Guide “STEP 1: Check the connection between Receiver Collar and Remote Transmitter”.
Q: Can I adjust the strength of Sound, Vibration, and Static?
On the Remote Transmitter, you can only adjust the Static Level. But on the APP, you can adjust the strength grade of all three functions.
Q: When using the Automatic Bark-stop function, my dog barks, but there is no trigger correction.
In order to remain humane in your treatment of your dog, the bark Collar performs corrective actions only if the barking volume is beyond a certain level. You can also customize the limit value of Loudness via the following steps.
Home→Trigger loudness

1. If the barking has exceeded your acceptable range but no corrective action is triggered, you can turn down the Loudness limit value in Settings.
2. If you want to relax the restrictions, allowing your dog to bark at a higher volume range, you can turn up the Loudness limit value.

Specifications and Performance

Product name: Smart Training Collar
Mode: Tls Pro
Battery Type: Li-Polymer
Battery capacity: 500mAh (Receiver Collar)
500mAh (Remote Transmitter)
Input interface: Micro-1M
Input parameters: 5V/0.9A Max. (Receiver Collar)
5 V/0.4A Max. (Remote Transmitter)
Static: 1-99 Levels
Remote range: 750 yards
Auto protection: If the static function is triggered 8 times in 1 minute, the device will cool down for 2 minutes to protect your dog.
Charging time: About 45min ( Receiver Collar)
About 120min ( Remote Transmitter)
Working time: About 2 weeks (Receiver Collar)
Material: PC+ ABS
Ingress protection: IPX7 ( Receiver Collar)
Packing list:
1 x Receiver Collar
1 x Remote Transmitter
1 x USB Charging Cable
1 x Test Light
1 x User Manual
6x Contact Points

Diagram

Receiver Collar: Receive the signal from the Remote Transmitter and execute the combined command. Remote Transmitter: Send the signal to the Receiver Collar.

Vibration Switch & Static Switch & Sound Switch:
Use for setting the combination command of Send Button.
Send Button:
Send combination commands to the receiver collar to train your dog
Settings Button:

1. Use for checking the status and lighting up the icons and indicators on the panel, including combination command, battery status, Automatic Bark-stop or not, and so on.
2. Enter a settable state for Static Level or Automatic Bark-stop settings.
3. Turn the Automatic Bark- stop function on or off, by pressing the button and holding it for 2 seconds when the device is in a settable state (static icon flashing).

Static Up or Down Button:
First, press the Settings button to enter the settable state, and then you can adjust the Static Level up or down a range of levels from 1 -99.
Display panel:
Used to display the status of the device, the indicator icons of selected functions will light up on the screen.

Receiver Collar Definitions

Function and Operation

Blue light stays on 3 seconds, with short vibration
Power off| In operating state, press and hold the Power Button for 2 seconds| Lights off, with long vibration for 1 second.
Low power mode| Let’s stand still for 10 minutes| Lights off
Exit low power mode| When a slight vibration is detected, including touching, picking up the device, , the dog turning, standing, walking, etc.| Resumes the standby state, the light flashes
Pairing mode| Double-click the Power Button (within 1.5 seconds)| Alternately flashes blue and green lights for about 90 seconds
Factory reset| Press the Power Button for more than 15s| The device vibrates when you keep pressing over 2 seconds, continue pressing for 15 consecutive seconds, then it will be reset to factory defaults.

LED Indications

Operating
state| 1. When Bluetooth is not connected to the mobile phone, the Green LED flashes.
2. When Bluetooth is connected to the mobile phone, the Blue LED flashes.
---|---
Low power
mode| Lights off, but when a slight vibration is detected, the light flashes
Pairing state| Green and blue lights flash alternately
Charging| Red light stays on
Fully charged| Greenlight stays on
Low battery| Red light quickly flashes when battery capacity is less than 15%

Remote Transmitter Definitions

Function and Operation

Set combination
command for the Send
Button| Turn on or off the toggle switches of Sound, Vibration and Static.| The indicator icons of selected functions light up for 5 seconds.
Check combination command| Touch Send Button.| 1.  The indicator icons of selected functions light up for 5 seconds.
2.  Static Level shows on the panel if Static Function is switched on.
Send combination commands| Click Send Button.| The indicator icons of selected functions flash.
Check the status| Click the Settings Button.| 1.  The icons of selected functions light up.
2.  If the Static Function is switched on, the Static Indicator icon flashes, and Static Level shows on the panel.
3.  If the Automatic Bark-stop is enabled, the Bark-stop icon shows on the panel.
4.  Remote and Receiver battery status show on the panel.

cannot be adjusted.
1.  Click the Settings Button.
2.  When the Static icon lashes.
press the Static Up or Down Button to adjust.| The Static Indicator icon flashes and Static Level shows on the panel.
Adjust Sound or Vibration level| Open the App and use your phone to set parameters in
Home page.| The Receiver Collards sounds or vibrates.
Double-click Function of Send Button| 1. Enable Double-click Function in the App
2. Double-click the Send Button on your Remote Transmitter.| The indicator icons of selected
functions flash.

Turned off: The Automatic Bark-stop icon disappears.
Pair with Receiver Collar| When the Receiver is in pairing mode.
Press the Up and Down Button at the same time more than 5 seconds.| The Receiver Battery Indicator lights up.

LED Indications

less than 15%.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirements in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>