Commercial Electric 1005837606 LED Direct Wire Linkable Under Cabinet Light User Guide
- June 4, 2024
- Commercial Electric
Table of Contents
Commercial Electric 1005837606 LED Direct Wire Linkable Under Cabinet
Light
THANK YOU
We appreciate the trust and confidence you have placed in Commercial Electric
through the purchase of this under cabinet light We strive to continually
create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you
for choosing Commercial Electric!
Product Description
SPECIFICATIONS
- The 12 in. fixture with SKU#1005837606(12 in.) is rated at 120V/60Hz 10.3W 77mA.
- The 18 in. fixture with SKU#1005837629(18 in.) is rated at 120V/60Hz 15W 115mA.
- The 24 In. fixture with SKU#1005837732(24 In.) Is rated at 120V/60Hz 19.6W 152mA.
Safety Information
Carefully read and understand the information in this manual before you begin
the installation. Failure to do so could lead to electric shock or a fatal
hazard.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user”s authority to operate the
equipment.
WARNING: This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of
the product and the hazards involved.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules and ICES-005 of the IC Rules. These limits are designed to provide reasonable installation protection. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving area.
- Increase the separation between the equipment and the receiver.
- Connect the equipment Into a different outlet and circuit from the receiver outlet and circuit.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
- This is a non-replaceable LED light source. Do not dismantle this fixture. There are no user-serviceable parts inside.
- For indoor and dry location use only.
- Do not touch the fixture when the light source is ON.
- Ensure the electricity is shut off before you install or work on this light. Either remove the fuse or turn off the circuit breaker. |
- Deviation from the assembly Instruction may result in a risk of fire and electric shock.
- Do not operate this fixture with a missing or damaged cover or housing.
- Do not mount this fixture near a heat source as it may damage this fixture.
- Do not stare directly into the LED light.
Pre-Installation
PLANNING INSTALLATION
Compare all parts with the parts listed in the Hardware Included and Package
Contents sections. If any part appears missing or damaged, do not install and
use this light. Contact customer service.
TOOLS REQUIRED
Package Contents
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| A | Connector | 1 |
| B | Wire connector | 1 |
| C | Tapping screw | 2 |
| D | Light fixture | 1 |
Installation
Preparing the light for installation
Remove two screws on the front of the fixture for access to the wiring
compartment
IMPORTANT: Keep the screws. You need them to install the front cover to
the fixture. There are no additional screws in the package.
- Determine the electrical feed location.
- Remove a knockout from either the back or side of the fixture housing. The fixture has two to four knockouts depending on the length of your fixture.
Connecting the wires
- Connect the ground wire from the fixture to the ground wire from the supply circuit, using the wire connector
- Connect the white wire (Neutral wire) from the supply circuit to the blue input (N) of the connector (A) inside the light.
- Connect the black wire (Live wire) from the supply circuit to the green input (L) of the connector (A) inside the light.
CAUTION: Make sure the white wire and the black wire are copper wires
among 14-20AWG. Make sure all the threads of the wires are properly connected.
NOTE: Before you connect the wires, make sure the ON/OFF switch on the
surface is OFF or tt may cause potential risk if the switch is ON.
Mounting the light fixture
NOTE: The fixture mounting screws are suitable for 0 cabinet bottoms 3/8
in. or thicker. Use shorter screws for thinner cabinet bottoms.
Attach the light to the desired surface using the fixture mounting screws (CJ.
Tighten the screws securely.
Re-attach the front cover
Re-attach the front cover back to the light fixture with the two
previously-removed screws. Restore the power to the electrical circuit at the
service panel. Tum on the switch to light the fixture.
NOTE: Ensure the wires are covered properly inside 0 the fixture.
To link more lights
Attention: Max linkage is 10 units. Only connect to the lights of the same series. Only ONE light is allowed to receive the main power input from the supply circuit. Otherwise, it will cause damage or fire.
- Turn off the power of the light and remove the front cover.
- Remove the side cover and release the linking cord from the clamp inside the light compartment.
- Extend the cord to the desired length and insert the cord into the connector of the next light.
- Place the extra cord back into the clamp and re-attach the front cover.
NOTE: These fixtures are dimmable and compatible with these dimmers sold at The Home Depot.
-
Make sure the lights are in a single loop and a single pole with the dimmers, and that the total wattage of the lights does not exceed the dimmer wattage capacity. Please refer to the wattage capacity on the dimmer packaging.
-
Please contact customer service if you have any further questions about the lights or dimmers.
(Mode#/SKU#): -
Lutron brand: DVCL-153PR-WH/396508; CTCL-153PDH-WH/267858; TGCL-153PH-WH/527401; P-PKG 1W-WH-R/1000027680;
-
Leviton brand: R62-06674-POW/125569; R60-IPL06-1 OM/976708
Support
Questions, problems, missing parts? Before returning to the store, call
Commercial Electric Customer Service Ba.m.-7 p.m., EST, Monday – Friday, 9
a.m.-6 p.m.Saturday. 1-877-527-0313
HOMEDEPOT.COM