emotn N1 Smart Bluetooth Projector User Manual
- June 11, 2024
- emotn
Table of Contents
emotn N1 Smart Bluetooth Projector
Dear Customer
Please read the product instruction carefully：
Thank you for purchasing and using the products. For your safety and
interests, you should read the Product Instruction carefully before using this
product.
About the product instruction:
The copyright of the instruction belongs to Super Creativity Limited.
Trademarks and names mentioned in the instruction belong to their respective
right owners.In case of inconformity between the content of the instructions
and the actual product, the actual product shall prevail.
- We reserves the right to interpret and modify the instructions.
We will not be liable for any personal injury, property, or other damage caused by your failure to comply with product instructions or precautions.
Projection Size Description
| Size | Screen (Length*Width:cm |
|---|---|
| 60 inches | 133*75 |
| 80 inches | 177*100 |
| 100 inches | 221*124 |
| 120 inches | 265*149 |
- The best recommended projection size is 100inches.
Packing List
Before using this product, please check that all items are in the box.
-
Projector
-
Remote Contro
-
Adapter
-
AC Cable
-
User Manual
Projector
Overview and interface description.
-
Front view
-
Rear view
-
Top View
-
Bottom View
Remote Control
- Open the battery compartment cover of the remote control.
- Install 2 AAA batteries. *
- Put back the cover
Remote Control Pairing
- Place the remote control within 10cm of the device.
- For first-time use, follow the on-screen instructions: Press “Volume Down” and “Right” simultaneously until an indicator light begins flashing.
- This means that the remote control enters the pairing mode.
- When the indicator light stops flashing, means connection is successful
Network
Enter [Settings]–[Network] Select the network of wired or Wi-Fi
Focus
Enter [Settings]–[Focus] Select [Auto Focus],the screen will automatically
clear.
Select [Manual Focus],press the remote control up/down button of the
navigation key to adjust the focus according to the displayed screen.
When the screen is clear, stop the operation.
Keystone Correction
Enter [Settings]–[Keystone] Select [Auto],the screen will be automatically
corrected.
Select [Manual],to adjust the four points and the size of the frame.
Inputs
Enter [Inputs]–HDMI/HOME/USB
Watch the content from the difference singal sources
IC STATEMENT
CAN ICES-3 (B)/NMB-3 (B)
This Class B digital apparatus complies with Canadian ICES-003.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device
For projectors only
The distance between user and products should be no less than 20cm
5.2 GHz band is restricted to indoor use only.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We declares that this device is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Satisfies all the technical regulations applicable to the product within the
scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical
Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic
Compatibility Regulations (SI 2016/1091).
This device operating frequency:2402-2480MHz(EIRP＜20dBm),2412-2472MHz(EIRP
20dBm),5150~5250MHz(EIRP＜23dBm),
5250~5350MHz(EIRP＜20dBm),5470~5725MHz(EIRP＜27dBm),5725~5850MHz(EIRP 13.98dBm)
Important Precautions
- Do not look directly at the projection beam with your eyes, because the strong beam may harm your eyes.
- Do not block or cover the heat dissipation holes of the device to avoid affecting the heat dissipation of internal parts and damaging the device.
- Keep away from humidity, exposure, high temperature, low pressure, and magnetic environment.
- Do not place the device in areas susceptible to excessive dust and dirt.
- Put the device to the flat and stable station, do not put it to the place prone to vibration.
- Please use correct type of battery for the remote control.
- Only use attachments/accessories specified or provided by the manufacturer.(such as the exclusive supply adapter, bracket etc.)
- Do not disassemble the device personally, repair the device only staff authorized by the company.
- Place and use the device in an environment of 0°C-40°C.
- Do not use the earphones for a long time. Excessive sound from the earphones can damage your hearing.
- The plug considered as disconnect device of adapter.
- As with any bright source, do not stare into the direct beam.
- The adapter shall be installed near the equipment and shall be easily accessible.
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc
Customer Service
Smart Projector
Model:N1
Input:19V ⎓ 6.32A ,120.08W
USB Output:5V ⎓ 1A
Manufacturer: Shenzhen Dangs Science and Technology Co.,Ltd.
For FAQs and more information, please visit:
https://www.emotn.com
support@emotn.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>