ANOLiS ArcDot-US LED Light User Manual
- June 3, 2024
- ANOLiS
Table of Contents
ArcDot-US LED Light
User Manual
ArcDot-US
The Anolis Arc Dot-US is a Cree MC-E RGBW multi chip based high powered multicoloured LED fixture. The unit´s high light output can be pixel mapped and therefore can be controlled and used for large scale matrix applications, as well as used for individual illuminating needs. Cast aluminium housing with frosted UV stable poly carbonate dome allows flexible solutions to both interior and exterior environments. The product is manufactured in two versions:
Attention
- Do not install the module near high inflammable liquids or materials
- Do not allow anything to rest on the module
- Do not install the module near the naked flames
- Do not install the module in dirty,dusty or badly ventilated location
- Avoid using the unit in locations subject to possible impacts.
- Avoid looking directly into the LED light beam at close range.
- Warning: Operation of this equipment in a residential environment could cause radio interference.
- Resistance of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use. Part 2: Immunity.
- The installation company should measure levels of possible interference’s above the tested levels E1, E2, E3 given by this standard (e.g. transmitters in surrounding area) before installing the equipment.
- Emission of the equipment complies with the standard EN 55032 Electromagnetic compatibility of multimedia equipment – Emission Requirements according to class A.
Installation
Four holes (5) of diameter of 5.5 mm in the ArcDot base (2) serve for mounting the base on a non-flammable flat surface. The supply cable (s) can be led through the slots (3) in the housing (1) of the Arc Dot or through the aperture (6) in the Arc Dot base .
- Fasten the Arc Dot´s base (2) on the mounting surface. Keep its orientation as shown on the picture above (sign DOWN has to lead down).
- Put the housing on the base, turn it to the right and secure with the screw M5 (4).
- Connect Arc Dots each other and to the power supply.
Use the following ways for connecting Arc Dots with two supply cables(example for matrix of 4 x 4).
Technical specifications
| LED device: | Cree MC-E RGBW multi chip |
|---|---|
| Max. current per colour: | 520 mA |
| Maximum power consumption: | 5.5 Watts/48V |
| Power supply: | 30-50 V DC ;suitable for damp locations |
30 V DC max. ;suitable for wet locations
Compatible power supplies:| Arc Pixel Power-US, Arc Power Unit Pixel Rack
Mount US, Arc Power Unit Pixel Wall Mount US, Arc Power Unit Pixel Rack Mount
US LV, Arc Power Unit Pixel Wall Mount US LV, DRS
Projected Lumen Maintenance:| L90B10 >90.000 hrs, Ta = 25°C / 77°F
Cooling system:| convection
Surface operating temperature:| +35°C @ ambient 25°C
Ambient operating temp.range:| -20°C/+50°C
Control electronics:| Internal chip protection against overheating Flicker-
free operation (300 Hz current driving of LEDs) Status messages for
communication with power supply unit
Design:| Housing & base: cast aluminium
Dome: frosted poly carbonate
Weight:| 0.2 kg
Mounting:| via 5 holes in base
IK rating:| IK10
Data cables:| Li9Y11Y, 2 x AWG16+1 x AWG 20(length according requirement,
standard length is 0.25m IN and 0.18m OUT)
Connectors:
Version 1: 1x Chogori CGRBB-03BMMA-SL8001 (male); 1x Chogori CGRBB-
03BFFA-SL8001 (female)
Version 2: 1x Chogori CGRBB-03BMMA-SL8001 (male), 1x T-connector Chogori
T-CGRBA-030303FFM-TS
Dimensions (mm):
Wiring of Arc Dot connectors
| Input | Output |
|---|---|
| Chogori CGRBB-03BMMA-SL8001 (male) | Chogori CGRBB-03BFFA-SL8001 (female) |
| 1 GND (blue wire) |
2 +48V (red wire)
3 Data (orange wire)| | 1 GND (blue vire)
2 +48V (red wire)
3 Data (orange wire)
Accessories
-
(P/N 13051564) T-connector Chogori T-CGRBA-030303FFM-TS /for product version 2 only/ 1x
-
(P/N 13052784) Cable Connection DRS/RU Pixel (CGR-F/bare,3pin, 1.5m)*
-
(P/N 13052738) Cable Connection DRS/RU Pixel (CGR-F/bare,3pin, 0.2m)*
-
(P/N 1305 2023) Connection cable ArcDot, 2m *
-
(P/N 1305 2024) Connection cable ArcDot, 4m*
-
(P/N 1006 2330) Active Terminator for ArcDot*
-
(P/N 1006 2331 Passive Terminator for ArcDot*
-
(P/N 13052738) Cable Connection DRS/RU Pixel (CGR-F/bare,3pin,0.2m)*
-
quantity depends on size of installation
https://www.anolislighting.com/resource/arcdottm-user-manual-us-
Version 2.2
June 22, 2019
Specifications are subject to change without notice.
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o.
Palackeho 416/20 CZ 75701
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>