GE GFD55GSSN Capacity Front Load Gas Dryer Instruction Manual
- June 3, 2024
- GE
Table of Contents
GE GFD55GSSN Capacity Front Load Gas Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
GAS DRYER RATING
120V: 60Hz, 8A
EXHAUST OPTIONS: 4-way via rear, left, right, and bottom. (The right,
left, and bottom venting options require Side Vent Kit: GFA28DSVN)
CIRCUIT REQUIREMENTS: An individual, properly grounded branch circuit,
protected by a 15-20 amp circuit breaker or a time-delay fuse, is required.
NOTE: The dryer wall outlet must be located within 36″ of the service
cord entry and accessible when dryer is mounted in position.
INSTALLATION INFORMATION: For complete information, see the installation
instructions packed with your dryer.
OPTIONAL LP CONVERSION KIT: WE25M87
STACKED INSTALLATION:
Brackets for stacking dryer over washer are not included with the washer.
Order part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION:
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back. The dryer MUST be exhausted to the
outside. Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0″ all sides and top. Closet doors must be louvered or
otherwise ventilated and must contain a minimum of 60 sq. in. of open area
equally distributed. If this closet contains both a washer and a dryer, doors
must contain a minimum of 120 sq. in. of open area equally distributed. No
other fuel-burning appliance shall be installed in the same closet with a gas
dryer.
BATHROOM OR BEDROOM INSTALLATION:
The dryer MUST be exhausted to the outdoors. The installation must conform
with the local codes, or in the absence of local codes, with the National
Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS:
Minimum clearances to combustible surfaces 0″ all sides and top.
FOR MORE INFORMATION ON VENTING KITS AND
FOR ACCESSORIES, PLEASE CALL 1-800-GE-CARES
STACKED DIMENSIONS (IN INCHES)
- PEDESTAL DIMENSIONS (IN INCHES)
- GFP1528PNDG – DIAMOND GRAY
- GFP1528PNRS – SAPPHIRE BLUE
- GFP1528PNSN – SATIN NICKEL
- GFP1528SNWW – WHITE
- This optional 16″ pedestal raises the door opening and height of the washer or dryer.
DRYER EXHAUSTING INFORMATION – METAL DUCT ONLY
For complete information, see the installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with a 4” diameter all-rigid metal exhaust duct. If a rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see the installation instructions packed with your dryer for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
- Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of the dryer, add one turn.
- The maximum length of a 4″ rigid (aluminum or galvanized) duct that can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn of 45° should be treated as a 90° elbow. Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampened wall cap to prevent back drafts, birds nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.
FEATURES AND BENEFITS
Built-in WiFi – Start, stop, and monitor your laundry from anywhere while
receiving real-time notifications and updates.
Quick Dry – Quickly dries items and small loads for families on the go.
Sanitize Cycle – Sterilize clothing with elevated temperatures designed
to kill common household bacteria.
Wrinkle Care – Prevents wrinkles by extending the tumble without heat.
HE Sensor Dry – Prevent over-drying and protect your clothing thanks to
innovative dual thermistor technology, that continually monitors temperature
and moisture.
Damp Alert – Signals when delicate clothes reach the ideal dampness level
for ironing or final air drying.
Vent Sensor – Provides alerts when a restriction is detected in your
dryer vent.
Way Venting – Easy-to-change venting options provide the ultimate
installation flexibility to fit in your home.
Reversible door – Easily reverse your washer and dryer door for superior
installation flexibility.
Model GFD55GSSNWW – White
Model GFD55GSPNDG – Diamond Gray
Model GFD55GSPRRS – Sapphire Blue
- For answers to your Monogram, GE Café™, GE Profile™, or For GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, at 800.626.2000.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>