GNCC GW3 4G LTE Cellular Security Camera User Manual
- June 13, 2024
- GNCC
Table of Contents
- GNCC GW3 4G LTE Cellular Security Camera
- What’s in the Box
- Device Overview
- Instructions for use
- Install the SIM Card
- Install the Micro SD Card
- Download and register App
- Connect the camera
- UBox Overview
- FAQs and Troubleshooting
- FCC Warning
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GNCC GW3 4G LTE Cellular Security Camera
What’s in the Box
Note: If the package or camera is damaged, some accessories are missing or the App connection fails, please contact us for help: nd.support@gncchome.com
Device Overview
- CD Lens
- Light Sensor
- IR LED
- PIR
- Microphone
- Indicator Light
- IR LED
- Micro SD Card Slot
- Reset Switch
- SIM Card Slot
- Power Switch
- Speaker
- USB Charge Port
- Charging Indicator
Instructions for use
Charge the Battery
- Charge the battery with a power adapter for the first use.
- Note: A 5V/1A or 5V/2A USB charger can be used.
- Charge the battery with the Solar Panel.
- Note: For better weatherproof performance, please always cover the USB charging port with the rubber plug after charging the battery.
- Show battery percentage UBox App-Me-Common settings-Show battery percentage.
Charging Indicator
- Red LED: Charging
- Blue LED: Fully Charged
Install the SIM Card
Insert the test SIM card provided by GNCC
This SIM card does not need to be activated, please insert it into the camera
directly. We provide 300MB of free data for testing. When it runs out of 300MB
of data, please top up on the UBox App or replace it with your own SIM card.
Insert your own SIM Card for the camera
You need to activate your own SIM Card for the Camera, the SIM card shall
support FDD and FDD LTE. Activate the card on your smartphone or with your
network carrier before inserting it into the camera.
Notes:
- Some SIM cards have a PIN code, please use your smartphone to disable the PIN first.
- Do not insert the loT card into your smartphone.
- The SIM card provided by GNCC is purchased from third parties EIOTCLUB, more service support about how to top up the SIM card, please contact GNCC support nd.support@gncchome.com
Install the Micro SD Card
Choose a Proper Micro SD Card
Please choose a Micro SD card with the specifications below so it can be
compatible with the camera.
- Capacity Up to12BGB
- Read and Write Speed Class 10 or higher 26Mbps
- Format FAT32
Notes:
Please format your Micro SD card with the computer if the card doesn’t work.
You can contact GNCC support for help:
nd.support@gncchome.com
Download and register App
Download
Ubox is available for both iOS and Android operation systems. Search the name
“UBox” in the App Store or Google Play, or scan the OR Code to download the
App. http://app.ubianet.com/app/ubox/
Register
Please click “Allow” or “Agree” to enable this App to access your camera and
phone. This will allow you to use the APP functions normally.
Notes:
UBOX APP is provided by a third party, please contact GNCC Support if you have
any question during the use of APP:
nd.support@gncchome.com
Connect the camera
-
Turn on the camera and reset it
In the off state, insert the Micro SD Card and SIM card, press and hold the power switch for 1-25 to turn on the camera, Red led lights up, then press and hold the Reset switch for several seconds until the voice prompts “System reset”. -
Scan the QR code on the camera
Blue led solid lights up and stays on, enter the “UBox App”, click “Add a device” to enter the Device List, and choose “Setup 4G Device”, and then please scan the QR code on the camera with UBox App. -
Add the camera
After a successful connection, you can modify the camera’s name and location manually and then click “Next” to add the camera.
Status LED for connection in progress and successful connection:
- Red light is always on -> red light is slow flashing > red and blue lights alternately slow flashing > red and blue lights flashing fast at the same time > blue light is always on.
- Red light is always on and slow flashing: The system is starting up.
- Red and blue lights alternately slow flashing: SIM card detection.
- Red and blue lights flashing at the same time: The operator’s network is being accessed.
- Blue light is always on: Successfully connect to the network and server.
Notes:
- When the camera is in standby mode, the status light is off and the default setting is to retry to access the network every 1 hour.
- If you have any questions about the connection, please contact GNCC support: nd.support@gncchome.com
UBox Overview
- Push Alarm
- Basic Settings
- State of the Device
- Add Smart Device
- Camera Name
- Definition of the Picture
- Time of the Device
- PlZ
- Sound of the Device
- Screenshot
- Intercom
- Picture Enlarge
- Camera/Device Settings
- Online User
- Battery Level
- IR/White LED Switch
- Full-Screen Preview
- Cloud/SD Card Storage Switch
- Manual Video Recording
- PTZ Speed
- Picture Zoom Out
Note
- Camera/Device settings (9) include Device name, Memory card, Image flip, Scene mode, Activity detection, Arming setting, Device alarm, Recording time, Power frequency, LED indicator, Synchronization time, Retry time, Volume settings.
- Basic settings (19) include Permission sharing, Cloud service, 4G traffic service, View UID, Delete device.
FAQs and Troubleshooting
Q: Can this camera work with 256GB micro SD card?
A: No, the camera can only support up to 128GB (fat 32, class 10 or above).
Q: Can I top up the offered SIM card?
A: Yes, you can top it up after entering Basic settings in UBox App. Or you
can enter the SIM card number at EIOTCLUB’s official website and select the
package to top up.
Q: How long can the solar panel power extension cable be connected?
A: The cable length of the Solar Panel is 3 meters.
Q: The camera was used in the US. If I take it to the EU countries, can it
work in EU countries?
A: No, the US version camera is not able to work in the EU countries.
Q: How long can the battery last?
A: The rechargeable battery is 8400mAh in capacity. It lasts for around 2
months in standby mode. The battery life may vary depending on different
mobile network service providers, signal strength, and other factors.
Q: Can this camera record continuously?
A: No, this battery-powered camera can only record motion videos.
Q: Can I add a user account and limit the features of a user account?
A: Yes, once one account scans the QR code to control the camera, other
accounts cannot scan the QR code to control the camera. However, you can share
it with friends and family through the sharing function on the app, and you
can customize the permissions.
Q: Can the SIM card provided be used on a mobile phone or other devices?
A: No, the attached lo T card has been bound by the device, and it is
forbidden to insert it into other devices for use, otherwise, the loT card
will be locked and cannot be used.
Camera Is Not Powering On
If your camera is not starting up, please try the following solutions:
- Make sure the power switch is turned on.
- Charge the battery with a DC 5V/2A power adapter. (When the blue light is on, the battery is fully charged.)
- If these don’t work, please contact GNCC Support: nd.support@gncchome.com
PIR Sensor Fails To Trigger Alarm
If the PIR sensor fails to trigger any kind of alarm within the covered area,
try the following:
- Make sure the battery is working.
- Make sure the SIM card is available.
- Make sure the Pl R sensor is enabled or the schedule is set up properly and running.
- Make sure that the PIR sensor or the camera is installed in the right direction.
- Check the sensitivity settings and make sure it’s set up properly.
- Tap on the UBox app go to Device Settings>PIR Settings and make sure the corresponding action is checked.
- Reset the camera and try again. If these don’t work, please contact GNCC support: nd.support@gncchome.com
Failed to add during network configuration
- Make sure the antenna is screwed tightly.
- Make sure the LTE signal is good enough.
- Make sure the SIM card is the recommended one and has been activated.
- If the SIM card is the one our camera supports and has been activated, please try to switch on and off the camera again.
- Make sure you reset it successfully before the network connection. If these don’t work, please contact GNCC Support: nd.support@gncchome.com
Why does the device not recognize the TF card
- 1ct Make sure the TF card is up to 128G (class 10 or above).
- Insert and remove the TF card after powering off.
- Please check if the TF card is working normally and whether it is in FAT32 format.
When the mobile phone or the device is working in an unstable network, the App also will prompt that the TF card can not be recognized. If these don’t work, please contact GNCC Support: nd.support@gncchome.com
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>