SWIT S-2070 Chip Array LED Camera Light User Manual
- September 5, 2024
- SWIT
Table of Contents
S-2070 Chip Array LED Camera Light
“`html
Specifications
- Input voltage: Varies
- Power consumption: Depends on power source
- Beam angle: Not specified
- illuminance: Varies
- Color temperature: 5600K and 3200K filters included
- CRI: Not specified
- Weight: Not specified
- Dimensions: Not specified
Product Information
The Chip-Array LED Camera Light S-2070 by SWIT Electronics Co.,
Ltd. features new generation chip-array LED technology, providing
bright but soft and glareless light output.
Product Usage Instructions
1. Power Supply
- Special Slim Battery S-8040:
-
Ensure the light is switched off.
-
Align a fully charged S-8040 battery to the DV mount slot and
press tightly in. -
Slide the battery downward to snap together.
- Standard DV Camera Batteries:
-
Align the S-7004 series battery plate to the DV mount slot and
press tightly in. -
Slide the battery downward to snap together.
-
Fix the DV mount with two screws.
- DC Cable:
-
Plug S-7104 into the DC-IN port of S-2070 and get power from
D-tap power output sockets or pole-tap DC adaptors. -
Ensure the DC connector is 5.5/2.1mm pole, input voltage is
between 6-17V, and polarity is inner positive, outer negative.
2. Fixing the LED Light to the Camera
Using the cold shoe mount, securely attach the LED light to the
camera for illumination during use.
FAQ
Q: Can I clean the light and diffuser with any cleaning
agents?
A: Clean the light and diffuser with a soft dry cloth or a soft
cloth dipped in neutral detergent. Avoid using wet cloths,
anhydrous alcohol, benzene, or mixtures of anhydrous alcohol and
ether to prevent damage.
Q: What should I do if the cooling vent is blocked?
A: Do not block the cooling vent. Ensure it remains clear to
prevent overheating and potential damage to the equipment.
“`
Chip-Array LED Camera Light S-2070
Ver: B
USER MANUAL SWIT Electronics Co., Ltd.
Features New generation chip-array LED technology, outputs bright but soft and
glareless light;
60°wide beam angle, equally spread light, single shadow; 13W power
consumption, 1100Lux @ 1meter, 10%-100% dimmer; 5000K color temperature, 5600K
and 3200K filter; 6V-17V wide voltage input via D-tap power cable or standard
DV battery; High intensity and toughness glass fiber housing, screw and cold
shoe mount.
Product view
Tel:+86-25-85805753 Fax:+86-25-85805296 http://www.swit.cc E-mail: contact@swit.cc
Fig 1
Fig 2
Cautions
1. Do not disassemble the light or touch the interior with metal objects to
prevent damaging the equipment. 2. Do not store the light in dusty or wet
environment to avoid damage. 3. Working temperature is between -10 and 40. 4.
Storage temperature is between -20 and 55. 5. Do not block the cooling vent.
Cleaning
Clean the light and diffuser with a soft dry cloth, or clean with a soft cloth
dipped with neutral detergent first, and then wipe with a soft dry cloth. Do
not clean the light and diffuser with a wet cloth, anhydrous alcohol, benzene,
mixture of anhydrous alcohol and ether to avoid damage.
1 5600K filter 2 Barn door 3 3200K filter 4 Barn door 5 Dimmer knob 6 Power Switch
7 Cooling vent 8 Fasten knob 9 Cold shoe 10 Cooling vent 11 DV plate slot 12 DC-IN socket
Specification
Input voltage Power consumption Beam angle
illuminance
Color temperature CRI Weight Dimensions
DC 6V~17V Approx. 13W Approx. 60° Approx. 1100lux @1m(5000K) Approx. 800lux@1m(5600K) Approx. 400lux @1m(3200K) 5000K and 5600K/3200K switchable 88 Approx. 274g 108mm×80mm×133mm
Packing List
1 S-2070 LED light 2 S-7004 series snap-on DV plateoptional for different
types 3 Portable bag 4 Warranty card 5 User manual
X1 X1 X1 X1 X1
1
Usage 1 Power supply
S-2070 accepts three ways of power supply: 1. By special slim battery S-8040;
2. By various standard DV camera
batteries; 3. By DC cable. By special slim battery S-8040 (Optional purchase)
Make sure there’s no power lead connected into DC-IN socket and the light is
switched off (turn the switch to “O”). Align a fully charged S-8040 battery to
the DV mount slot to the same side, and press tightly in. Slide the battery
downward to snap together. See Fig 3.
By various standard DV camera batteries
Align the S-7004 series battery plate to the DV mount slot to the same side,
and press tightly in. Slide S-7004 downward to snap together. See Fig 4.
Fix the DV mount with two screws. Make sure the light is switched off (turn
the switch to “O”). Mount a
fully charged battery to the S-7004 mount. See Fig 4.
Remark: Select a compatible S-7004 battery plate to match your DV battery:
Model
Compatible battery
Recommended SWIT battery
S-7004F S-7004D S-7004C S-7004U S-7004E S-7004B S-7004V
S-7004I
SONY NP-970/770 Panasonic D54S, VW-VBD58 Canon BP-945/970G SONY BP-U60/U30
Canon DSLR LP-E6 Panasonic VW-VBG6 JVC BN-VF823
JVC SSL-JVC50
S-8975/S-8972/8970/8770/LB-SF65C S-8D62/S-8D58/S-8D98/LB-PD65C S-8945/8845
S-8U63/LB-SU90C S-8PE6 S-8BG6 S-8823
S-8i50/S-8i75
By DC cable Make sure the light is switched off (turn the switch to “O”). Plug
S-7104
(Optional) into the DC-IN port of S-2070 and get power from D-tap power output
sockets, such as batteries, battery plates. You can also select SWIT pole-tap
to poletap DC cable S-7108 (Optional)) to get power from pole-tap DC adaptors.
For third-party DC cables, please make sure the DC connector is 5.5/2.1mm pole
and input voltage should be 6-17V; and polarity inner positive, outer
negative. See Fig 5.
2 Fix the LED light to the camera By Cold shoe
Anticlockwise revolve the fasten knob, till the screw bolt is back into the
cold shoe slice. Align the cold shoe slice with the cold shoe mount on the
camera handle. Clockwise revolve the fasten knob to install the light onto the
camera.
By 1/4″ screw mount
Clockwise revolve the fasten knob, till the screw bolt is out of the cold shoe
slice. Align the screw bolt with the 1/4″ screw thread on the camera handle.
Continuously clockwise revolve the fasten knob to install the light onto the
camera.
3 Adjust the angle of the light:
Hold the light, and adjust the light upward or downward. See Fig 7.
4. Open barn doors and filters:
Open the barn doors and filters to about 45°. See Fig 1
5. Switch on: Turn the switch to “I”.
6. Adjust the illuminance:
Adjust the illuminance from 10% to 100% by the dimmer knob.
7. Adjust color temperature:
Output 5600K light by using 5600K filter (See Fig1 -) Output 3200K light by
using 3200K filter (See Fig1 )
2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>