SERVER 87740 Conservewell Mounted Utensil Holder Instruction Manual

: June 4, 2024
: SERVER

Table of Contents

SERVER 87740 Conservewell Mounted Utensil Holder
INSTALLATION
PROGRAMMING TIMER
TROUBLESHOOTING
WIRING DIAGRAM
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SERVER 87740 Conservewell Mounted Utensil Holder

WARNING ELECTRICAL SHOCK COULD OCCUR

Electrical components of unit could be damaged from water exposure or any liquid.
Never immerse unit into water or any liquid.
Never use any water jet or pressure sprayer on unit.
Ensure unit is “OFF” and unplugged.

DISHWASHER SAFE – HANDWASH ONLY

CLEAN
- Wash water pans with soap and hot water.
RINSE
- fully with clear water. 2
SANITIZE
- all parts according to local sanitization requirements. All parts in contact with food must be sanitized.
3AIR DRY
- all parts fully

CARE OF STAINLESS STEEL

The water pans and exterior of this unit are constructed of stainless steel.
If you notice corrosion beginning on any stainless steel surface, you may need to change the cleansing agent, sanitizing agent, or the cleaning procedures you are using.
A mildly abrasive nylon or brass brush may be used to remove any stubborn deposits on interior surfaces of unit.
Fully rinsing and drying all parts can help prevent corrosion. Elements and minerals in tap water can accumulate on stainless steel parts and create corrosion.
Do not use abrasive, caustic or ammonia based cleansers.
Do not use products containing acids, alkalines, chlorine, or salt. These agents can corrode stainless steel.
Do not use metal scrapers or cleaning pads that could scratch surfaces

SERVER PRODUCTS LIMITED WARRANTY

This Server product is backed by a two-year limited warranty against defects in materials and workmanship. See Server-Products.com for details.

GENERAL SERVICE, REPAIR OR RETURNS

Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours. Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge. Electrical parts (thermostats, heating elements, etc.) are not returnable. Servicing Cord: Specific tools are required for safe and proper power supply cord removal and installation. If cord must be replaced, only a representative of the OEM (original equipment manufacturer) or a qualified technician may replace cord. Cord must meet code designation H05 RN-F requirements.

YOU WILL NEED

Screwdriver
Appropriate fasteners

INSTALLATION

INSTALL UNIT
- Select wall location or sturdy vertical surface for mounting. Determine proper mounting hardware you will need to supply. Locate mounting holes apart approximately 27 cm (10-5/8″). Key slot mounting brackets make removal easy
INSERT WATER PANS
- Fill each pan with approximately 0.7 liter (3/4 quart) of HOT water. See page 2 for water temperatures. Insert both pans of water into basin
PLUG CORD INTO POWER SOURCE
TURN UNIT ON

ONLY USE WITH UTENSILS SAFE IN HIGH TEMPERATURES

WATER CHANGE-OUT

```
*  REMOVE & EMPTY PANS OF WATER
```
- REFILL & RETURN WATER PANS TO BASIN

USING THE COUNTDOWN TIMER

PRESS RESET TO START THE COUNTDOWN CYCLE
PRESS RESET TO STOP ALARM
CHANGE OUT WATER
Complete “WATER CHANGE-OUT” steps listed above.
PRESS RESET BUTTON to restart the countdown cycle.

PROGRAMMING TIMER

SET COUNTDOWN CYCLE TIME

```
* ENTER TIME PROGRAM MODE:
```
- Simultaneously press and hold the
- UP and RESET buttons for 10 seconds.
- Red light indicates unit is in timer program mode.
- SELECT DESIRED COUNTDOWN TIME:
- Press the UP or DOWN buttons.
- LOCK IN TIME SETTING AND EXIT
PROGRAM MODE:
Press and hold the RESET button for 3 seconds.

SET ALARM VOLUME

```
* ENTER ALARM PROGRAM MODE
```
- Simultaneously press and hold the
- DOWN and RESET buttons for 10 seconds.
- Beeping indicates unit is in alarm program mode.
- SELECT ALARM VOLUME:
- Press the UP or DOWN buttons. A beep accompanies each level to indicate the volume setting. Volume level is shown in display. Adjust number to desired volume level.
- LOCK IN VOLUME SETTING AND EXIT
PROGRAM MODE:
Press and hold the RESET button for 3 seconds.