BRESSER 7002580 WiFi Colour Weather Station + 5-in-1 Multisensor Instruction Manual

Weather Station
WI-FI Colour Weather Station + 5in1 Multisensor
Instruction manual

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

| | |
---|---|---|---

www.bresser.de/P7002580

| www.bresser.de/P7002581| www.bresser.de/P7902580|

www.bresser.de/P7902581

WARRANTY

www.bresser.de/warranty_terms

www.bresser.de/P7802580

APP DOWNLOAD:

| Weather Underground is a registered trademark of The Weather Channel, LLC. in the United States and around the world. The Weather Underground Logo is a registered trademark of Weather Underground, LLC. To learn more about Weather Underground, visit www.wunderground.com
---|---
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google Inc.
Product| Art.No.:
---|---
Base station + wireless 5-in-1 Sensor (A, B, C, D)| 7002580 (black), 7002581 (white)
Only Base stations (A, B)| 7902580 (black), 7902581 (white)
Only Wireless 5-in-1 Sensor (C)| 7802580

Imprint (German)

Bresser GmbH
Gutenbergstr. 2
46414 Rhede
Germany
http://www.bresser.de
For any warranty claims or service inquiries, please refer to the information on “Warranty” and “Service” in this documentation. We apologize for any inconvenience caused by the fact that we cannot process inquiries or submissions sent directly to the manufacturer’s address. Errors and technical changes excepted.
© 2021 Bresser GmbH
All rights reserved.
The reproduction of this documentation – even in extracts – in any form (e.g. photocopy, print, etc.) as well as the use and distribution by means of electronic systems (e.g. image file, website, etc.) without prior written permission of the manufacturer is prohibited.
The designations and brand names of the respective companies used in this documentation are generally protected by trade, trademark and/or patent law in Germany, the European Union, and/or other countries.

Validity note

This documentation is valid for the products with the following article numbers:
7002580 7002581 7902580 7902581 7802580
Manual version: 0321
Manual designation:
IM_7002580-7002581-7902580-7902581-7802580_WIFI-Colour-Weather- Station_ende_BRESSER_v032021a
Always provide information when requesting service.

Features

• Measurement of Rainfall
• Measurement of wind speed
• Measurement of wind direction
• Radio-controlled clock with DCF signal reception and display
• Alarm with snooze function
• Outdoor temperature alarm (frost warning)
• Outdoor temperature (in °C or °F)
• Indoor temperature (in °C or °F)
• Humidity indoor/outdoor
• Atmospheric pressure
• SINCE function to display the total rainfall from a customized point in time.
• The highest and lowest value display
• Maximum/Minimum value memory
• Colour display
• Backlight

About this Instruction Manual

NOTICE
These operating instructions are to be considered a component of the device.
Read the safety instructions and the operating manual carefully before using this device.
Keep this instruction manual in a safe place for future reference. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

General safety instructions

**DANGER
Risk of an electric shock!**
This device contains electronic parts that are powered by a power source (AC adapter and/or batteries). Improper use of this product may result in electric shock. Electric shock can cause serious or fatal injuries. It is therefore imperative that you observe the following safety information.

• Never leave children unattended when handling the device! Follow the instructions carefully and do not attempt to power this device with anything other than the power sources recommended in this instruction manual, otherwise, there is a danger of an electric shock!
• Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation, and before any maintenance and cleaning work.
• Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the main supply.
• To disconnect the unit from the mains, always pull the mains plug and never pull the cable!
• Check this device, cables, and connections for damage before use.
• Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
• Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.

DANGER
The danger of suffocation!
Improper use of this product may result in suffocation, especially for children. It is therefore imperative that you observe the following safety information.

• Keep packaging materials (plastic bags, rubber bands, etc.) away from children! There is a danger of choking!
• This product contains small parts that can be swallowed by children! Choking hazard!

DANGER
Explosion hazard!
Improper use of this product may result in fire. It is essential that you observe the following safety information in order to avoid fires.

• Do not expose the device to high temperatures. Use only the supplied AC adapter or the recommended batteries. Do not short-circuit the device or batteries or dispose of them in fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!

NOTICE
The danger of material damage!
Improper handling may result in damage to the unit and/or accessories. Therefore, use the device only in accordance with the following safety information.

• Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary.
• Do not expose the device to high temperatures and protect it from water and high humidity.
• Do not immerse the unit in the water!
• Do not subject the device to excessive vibrations.
• Only use accessories and spare parts for this device that comply with the technical specifications.
• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or types or with different capacities. Remove batteries from the device if it is not to be used for a longer period of time!
• Do not use rechargeable AA batteries, as these will not give out the correct voltage for use.

NOTICE
The danger of voltage damage!
The manufacturer accepts no liability for voltage damage as a result of incorrectly inserted batteries, or the use of an unsuitable mains adapter!

Parts overview Base station

Illustration 1: All parts of the base station

(display of different atmospheric pressure values)
5 INDEX button (display change between ‘feels like temperature, dew point, heat index, and wind chill index)| 6 WIND button (display change between average and current gust)
7 MAX/MIN button (switch between highest, lowest, or current value display)| 8 HISTORY button (retrieve measurements for the past 24 hours)
9 CHANNEL button (channel selection)| 10 CLOCK button (manual time setting)
11 ALARM button (Alarm setting)| 12 ALERT button (e.g. set temperature alarm)
13 Wall mount| 14 DOWN button (Value setting downwards)
15 UP button (Value setting upwards)| 16 RESET button (reset all settings)
17 HI/LO/OFF slide control (setting or turning off backlight)| 18 Stand, removable
19 REFRESH button (refreshing data manually)| 20 SENSOR/WI-FI button (start manual sensor search or activate/deactivate WI-FI)
21 Battery compartment (cover)| 22 BARO UNIT button (change of atmospheric pressure measurement unit)
23 °C/°F button (display change between °C or °F)| 24 12/24 button (display change between 12 and 24 hours mode)
25 Power supply socket| 26 Power adapter

Parts overview Multisensor

Illustration 2: All parts of the multisensor

Scope of delivery

Base station (A), power adapter (B), stand (C), multifunctional outdoor sensor (D), mounting rod (E), mounting shoe (F), pipe clamp (G), screws, 1 pc. CR2032 type battery (base unit), instruction manual
Also required (not included in delivery): 3 x 1.5V batteries type AA/LR6 (outdoor sensor)

Screen display

Illustration 3: Screen display

Before commissioning

NOTICE
Avoid connection faults!
In order to avoid connection problems between the devices, the following points must be observed during commissioning.

1. Place the base unit (receiver) and sensor (transmitter) as close together as possible.
2. Connect the power supply to the base unit and wait until the indoor temperature is displayed.
3. Establish a power supply for the sensor.
4. Set up/operate the base unit and sensor within the effective transmission range.
5. Make sure that the base unit and the radio sensor are set to the same channel.

When changing the batteries, always remove the batteries in both the base unit and the sensor and reinsert them in the correct order so that the radio connection can be re-established. If one of the two devices is operated via a mains power connection, the power connection for this device must also be disconnected briefly when changing the battery. If, for example, only the batteries in the sensor are replaced, the signal cannot be received or can no longer be received correctly.
Note that the actual range depends on the building materials used in the building and the position of the base unit and outdoor sensor. External influences (various radio transmitters and other sources of interference) can greatly reduce the possible range. In such cases, we recommend finding other locations for both the base unit and the outdoor sensor. Sometimes a shift of just a few centimeters is enough!

The first steps

Follow the bullet points in order, to ensure a successful setup.

1. Setting up power supply (base station and wireless sensor)
2. Mount the wireless sensor
3. The base station is now in AP mode (LED flashes green) and ready for initial setup.
4. Create an account with a weather service provider compatible with your station, e.g. wunderground.com or weathercloud.net, and add the station to your account (“My Profile” / “Add Weather station”) or (“Devices” / “+ New”). Make a note of the station ID and password, as they will be needed in the next step. Write down the Station ID and Password, because they are needed in the next step.
5. Setting up the base station (Establish WIFI / Router connection)
6. Viewing weather data via the web, mobile, or tablet

Setting up power supply

Base station

1. Insert the DC connector into the connection socket of the base station.

2. Insert the mains plug into the power outlet.

3. The device is energized directly.
   Remote sensor

4. Loosen the screw at the battery compartment cover with a small Philips screwdriver and remove the cover.

5. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

6. Replace the cover and retighten it with the screw.

Attaching rubber linings

Attach the supplied self-adhesive rubber pads to the clamps as shown to ensure a firmer fitting of the mounting rod.

Assembling and installing the multifunctional remote sensor

Depending on the desired location, the remote sensor can be installed in two different ways.
NOTICE! During the assembly make sure that the upper part of the wind vane is a minimum of 1.5 meters off the ground. Use the circular level in the sensor head to ensure a level installation. The windmill must point to the North.

Assembly on a vertical or horizontal wooden element

1. Slide one end of the assembly bar into the aperture below the sensor head.

2. Slide one screw through the borehole and put it on the nut on the opposite side. Tighten the screw connection by hand.

3. Depending on the desired orientation, slide the opposite end of the assembly bar into the aperture for vertical or horizontal mounting of the assembly base.

4. Slide another screw through the borehole of the assembly base and put it on the nut on the opposite side. Tighten the screw connection by hand.

5. Place the assembly base with its bottom site first on a wooden element. Use 4 wood screws to tighten it.
   Assembly on a vertical or horizontal tube

6. Repeat steps 1 to 4 as before.

7. Place the assembly base with its bottom site first on the tube. Push the tube bracket against the tube from the opposite site.

8. Slide 4 screws through the bore holes of the assembly base and through the bore holes of the tube bracket on the other side.

9. Put on the 4 nuts and tighten the screw connection by hand.

Signal transmission

The base station automatically connects to the multi outdoor sensor and (if available) to other wireless sensors. You can also press the WIFI / SENSOR button to search directly for the sensors. If the connection is successful, the outdoor symbol (OUT) and/or the channel will appear on the display.
Connection status display:

Create a user account for Weather Underground (optional)

1. Enter the following web address for the ‘Weather Underground’ service in the address bar of your web browser: https://www.wunderground.com
2. Click on ‘Join’ to get to the registration page.
3. Enter your personal user data and click on ‘Sign up.
4. Follow the further setup steps.
5. Under the menu item ‘Sensor Network’ > ‘Connect a Weather Station’ your own weather station can be added.
6. A ‘Station ID’ and a ‘Station Key/Password’ are automatically generated by the service, which is needed for the following configuration of the weather station.

NOTICE! Use a valid e-mail address for registration. Otherwise, the service can not be used.

Create a user account for weather cloud (optional)

1. Enter the following web address in the address bar of the web browser: https://weathercloud.net
2. Under ‘Join us today’ enter the personal user data and click on ‘Sign up.
3. After successful registration and verification of the e-mail address, select the menu item “Devices” under the user account.
4. Click the ‘+New’ link under ‘Devices’ and enter the device and location data in the ‘Create New Device’ window to create a new device. Select the appropriate weather station under ‘Model’. For ‘Link type’ select the option ‘Pro Weather Link’.
5. A ‘weather cloud ID’ and a ‘key’ which are needed for the following configuration of the weather station are automatically generated by the service. These can be reached via the account at weathercloud.net under Devices > Settings > Link.

NOTICE! Use a valid e-mail address for registration. Otherwise, the service can not be used.

Configuration/Setting up a WI-FI connection

1. If the base station has not yet been connected to a router, it will switch to AP (Access Point Mode) mode after the first power supply. The display will show ‘AP’ and the symbol for WI-FI synchronization.

2. Use a smartphone, tablet, or computer to connect to Wi-Fi.
   NOTICE! The respective device itself must also be equipped with a WI-FI function.

3. In the system settings of the device, switch to W-LAN or WI-FI settings and select the wireless network (SSID) named ‘PWS-XXXXXX’.

4. After successful connection via the address bar of the web browser, enter the IP address ‘http://192.168.1.1‘ to establish a connection to the settings menu of the weather station.
   NOTICE! Always prepend ‘http://’ to the IP address to avoid browser- dependent connection errors. Recommended browsers: the latest version of Chrome, Safari, Edge, Firefox, or Opera.

5. Make the following settings in the settings menu:
   *Leave the field blank if registration is not yet available and entries are to be made later.
   **Manual setup requires additional router information (including e.g. IP address, SSID, etc)

6. After completing the settings, the device will recognize the default WI-FI connection after each restart.

7. In Access Point Mode, the WI-FI/SENSOR button can be pressed for 6 seconds to restore the previous settings.

WI-FI connection status:

WI-FI symbol is shown in the display| WI-FI symbol flashes in the display| AP symbol flashes in the display
---|---|---
Connection to the WI-FI router successful| The connection to the WI-FI router is not stable or ongoing connection| Access Point Mode enabled

Automatic time setting

After the power supply and the Wi-Fi connection are established, the time and date information is automatically transmitted by the Internet time server.
If the time/date information is received correctly, the date and time are set automatically and the reception symbol is displayed.
If the time/date information was not received or not received correctly, proceed as follows:

1. In countries/regions whose time zone differs from the coordinated world time UTC, the time zone must be set manually (see chapter ‘Setting the time zone’) in order to display the correct time.
2. Press the REFRESH button on the base unit for about 2 seconds to re-initiate the retrieval of Internet time information.
3. Check the W-LAN settings on the base unit for the correctness and correct them if necessary so that an Internet connection can be established (see chapter ‘Establishing a W-LAN connection’).

Manual time setting

To set the time/date manually, first, disable the reception of the time signal by pressing the RCC button for approx. 8 seconds.

1. Press and hold the CLOCK SET button for approx. 3 seconds to change to time setting mode.

2. Digits to be set are flashing.

3. Press the UP or DOWN button to change the value.

4. Press the CLOCK SET button to confirm and continue to the next setting.

5. Settings order: time offset > daylight saving time on/off > hours > minutes > 12/24 hours mode > year > month > day > day/month display change > time synchronization on/off > language
   NOTICE! When time is set manually, the time synchronization must be deactivated.

6. Finally, press the CLOCK SET button to save the settings and exit the setting mode.
   NOTICE! In normal display mode, press the CLOCK SET button to switch between the year display and date display. In setting mode, press the CLOCK SET button for about 2 seconds to return to the normal display mode.

Time zone setting

To set a different time zone, proceed as follows:

1. Press and hold the CLOCK SET button for approx. 3 seconds to change to time setting mode. The current value for the time offset flashes.
2. Press the up or DOWN button to set the desired hour value (0 to 10 hours) for the time offset.
3. Finally, press the CLOCK SET button for approx. 3 seconds to save the settings and exit the setting mode.

Manual measurement display

1. Press MAX/MIN button several times to display the stored values one after another.
2. Display order: Current values > MAX (highest values) > MIN (lowest values)
3. When highest or lowest values are displayed, press and hold the MAX/MIN button for approx. 3 seconds to switch the temperature unit display from °C to °F or reverse.

Technical data

Base unit

Temperature measuring range| DC 5V 1A power plug
Type: HX075-0501000-AX
---|---
Power supply:| -5°C to 50°C
Maximum number of sensors| 1x wireless multisensor
1x wireless internal sensor (optional)
Dimensions| 79 x 157 x 41 mm (W x H x D)
Weight| 130 g

Multisensor

SPECIFICATIONS

function, PC or notebook, Android or iOS smartphone/tablet
Supported internet browsers| Internet browsers that support HTML 5

EC declaration of conformity

Hereby Bresser GmbH declares that the radio equipment type with 7002580 7002581 7902580 7902581 7802580 complies with Directive 2014/53/EU. The full text of the EC declaration of conformity is available at the following Internet address http://www.bresser.de/download/7002580/CE/7002580_7002581_7902580_7902581_7802580_CE.pdf

UKCA Declaration of Conformity

Bresser GmbH has issued a “Declaration of Conformity” in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet address: http://www.bresser.de/download/7002580/UKCA/7002580_7002581_7902580_7902581_7802580_UKCA.pdf
Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6Hf, Great Britain

Disposal

Dispose of the packaging materials properly, according to their types, such as paper or cardboard. Contact your local waste disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner.
Batteries and rechargeable batteries must not be disposed of with household waste. You are legally obliged to return used batteries and accumulators and can return the batteries after use either in our sales outlet or in the immediate vicinity (e.g. in the trade or in municipal collection points) free of charge.
Batteries and accumulators are marked with a crossed-out dustbin and the chemical symbol of the pollutant, “Cd” stands for cadmium, “Hg” stands for mercury and “Pb” stands for lead.

Please contact the service center first for any questions regarding the product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
Telephone*: +44 1342 837 098

BRESSER UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom

*Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Contact
Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope

References

• art.no
• DT Cloud - Digital Transformation Cloud Platform
• konsoleH :: Login
• ground.com is coming soon
• Weathercloud | Global network of weather stations
• Bresser | Startseite | Expand Your Horizon mit BRESSER
• Bresser | Startseite | Expand Your Horizon mit BRESSER
• index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
• Bresser | BRESSER WLAN Farbwettercenter mit 5-in-1 Profi-Sensor | Expand Your Horizon
• Bresser | BRESSER WLAN Farbwettercenter mit 5-in-1 Profi-Sensor weiß | Expand Your Horizon
• Bresser | BRESSER 5-in-1-Außensensor für Wettercenter 7002510/7002511/7002512/7002513 ab LOT-Nummer 1156743 und 7002580 | Expand Your Horizon
• Bresser | BRESSER zusätzliche / Ersatz-Basisstation für 7002580 Wetter Center | Expand Your Horizon
• Bresser | BRESSER zusätzliche / Ersatz-Basisstation für 7002581 Wetter Center weiß | Expand Your Horizon
• Local Weather Forecast, News and Conditions | Weather Underground
• Weathercloud | Global network of weather stations
• Local Weather Forecast, News and Conditions | Weather Underground

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>