FLYSKY FS-R7D Receiver User Manual

: June 3, 2024
: Flysky

Table of Contents

Introduction
Receiver overview
Product specifications
Binding
Car lamp control
Firmware update
Failsafe
Certification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FS-R7D Receiver
User Manual
FLYSKY FS-R7D

Introduction

FS-R7D is a light group receiver in compliance with the ANT protocol, providing 7 channels. It is equipped with a single antenna externally, supporting the 2-way transfer- back function. It can output PWM signals and light control signals, featuring the compact design. FS-R7D can be adapted to a variety of vehicle models.

Receiver overview

[1] CH1(PPM)
[2] CH2
[3] CH3
[4] CH4
[5] CH5
[6] CH6
[7] CH7
[8] Flash light interface
[9] Backup light interface
[10] Tail light interface
[11] Headlight interface| [12] Right turn signal light interface
[13] Left turn signal light interface
[14] LED
[15] Antenna
[16] Bind button
[17] + (Power anode for light interface)
[18] – (Power cathode for light interface)
[19] S (Signal pin ）
[20] + (Power anode for channel interface)
[21] – (Power cathode for channel interface)
---|---

Product specifications

Product Model: FS-R7D
Compatible Transmitters: FS-G7P(Surface transmitters with ANT protocol)
Model Type: Cars
PWM Channels: 7
Numbers of Light Interface: 6
RF: 2.4GHz ISM
2.4G Protocol: ANT
Antenna: Single external antenna(Coaxial)
Input Power: 3.5 ～ 9V /DC
Working Current: < 90mA（5V）
Data Output: PWM/PPM
Maximum Power: < 20dBm (e.i.r.p.) （EU）
Distance: >300m(Ground distance without interfence)
Online Update: Yes
Water Proof: PPX4
Color: Black
Temperature Range: -10℃ ~ +60℃
Humidity Range: 20%~95%
Dimensions: 3523.313.3mm
Weight: 8g
Certifications: CE, FCC ID：2A2UNR7D00

Binding

The receiver supports two -way binding and one-way binding. The transmitter will display the information returned from the receiver after the two-way binding is completed.
Follow the steps below to bind in two-way binding:

Set 2 WAY for RF standard of the transmitter, then put the transmitter into bind mode.
Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.
• In Addition, the receiver has not been connected to the transmitter when it is powered on. Press and hold the BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.
When the LED of the receiver is solid on, the binding process should be completed. The transmitter exits the bind mode automaticlly.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Follow the steps below to bind in one-way binding:

Set 1 WAY for RF standard of the transmitter, then put the transmitter into bind mode.
Put the receiver into bind mode (Refer to the description above for entering bind mode).
When the LED of the receiver is in slow flashing state, the binding process should be completed. You need to manually put the transmitter to exit the bind mode. Then the LED of the receiver is solid on, indicating that the binding is completed.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.
Note: Put the transmitter in bind mode first, then put the receiver in bind mode.

Car lamp control

The lights are mainly controlled through CH1 and CH2, i.e. the working status of the lights is controlled by hand wheel and trigger.
The details are as follows:

Name	Working mode	Trigger condition
Left turn light	Slow flash	Left turn
Right turn light	Slow flash	Right turn
Headlight	Solid ON	Steering wheel clockwise fast rotation for three times

Notes:

After the receiver is powered on, all lights perform self-test immediately. After the lights are on for 1 second, they are off.
By default, the headlights and strobe lights are off.
Steering CH1 and throttle CH2 can automatically identify the neutral position.

Firmware update

The firmware of this receiver is updated through the FlyskyAssistant (Only version 3.0 or above is supported. The firmware of FlyskyAssistant is available on the Flysky official website).
This receiver can be updated via the following two ways:

After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the computer, then open the FlyskyAssistant on the computer to update the firmware.
Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following way (The LED of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on the computer to update the firmware.
• Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the receiver operates in three-flash-one-off manner repeatedly, then release the BIND button.

Failsafe

The failsafe function is used to output the channel value according to the out-of-control protection value set by the user after the receiver loses its signal and is out of control to protect the model and personnel.
It can also be set failsafe for each channel respectively. This receiver supports two failsafe modes: ON and OFF OFF It is no output for the interface of PWM.
ON Outputs the failsafe values set for each channel.

Attentions:

Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver’s battery is disconnected before turning off the transmitter, failure to do so can result out of control.
Unreasonable setting of the Failsafe may cause accidents.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver’s antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.

Certification

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FS- R7D] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flysky-cn.com.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

FCC ID: 2A2UNR7D00
Manufacturer：ShenZhen FLYSKY Technology Co.,Ltd
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd