FLYSKY Noble NB4 Pro Plus Transmitter Instruction Manual
- June 1, 2024
- Flysky
Table of Contents
FLYSKY Noble NB4 Pro Plus Transmitter Instruction Manual
Product Installation Using Instruction
Remove the steering wheel;
Pinch the brake pad with two fingers and take out
upwardly;
Remove the screws by turning them counterclockwise with a metric 1.5 mm
hexagonal screwdriver;
Steering wheel base detached;
Remove the screws(PWA2.1*6mm);
Remove the cap;
Remove the upper steering wheel pad cover;
Lift the spring hook with one hand and remove the steering wheel shaft with
the other hand;
Lift the spring hook with one hand and remove the steering wheel shaft with
the other hand;
Remove the spring hook and the spring component, then replace the spring;
Install the spring component;
Lift the spring hook with one hand and install the steering wheel shaft with
the other hand;
Install the upper steering wheel pad cover;
Install the cap；
Lock the screws(PWA2.1*6mm);
Connect the FPC wire;
Lock the screws(HB29mm);
Use the mounting slot of the steeringwheel with brake pad adjustment hole to
place over the protruding connector of the brake pad, then press the steering
wheel to fix it;
Insert the screw(HM312) into the screwhole used to secure the steering wheel,
then align a metric 2.5mm hexagonal screwdriver with the hexagonal hole in the
head of the screw, hold the side of the steering wheel with one hand and turn
the screwdriver clockwise with another hand until the screw is secured;
Use the mounting slot of the steering wheel with brake pad adjustment hole to
place over the protruding connector of the brake pad, then press the steering
wheel to fix it;
Insert the screw(HM3*12) into the screwhole used to secure the steering wheel,
then align a metric 2.5mm hexagonal screwdriver with the hexagonal hole in the
head of the screw, hold the side of the steering wheel with one hand and turn
the screwdriver clockwise with another hand until the screw is secured;
Complete the steering wheel spring replacement.
Certification
-
DoC Declaration
Hereby, [ShenZhen Flysky Technology Co., Ltd.] declares that the Radio Equipment [Noble NB4 Pro+(Noble NB4
Pro+)] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flyskytech.com/info_detail/10.html -
CE Warning
The ce warns that the installation of the antenna used in this transmitter must be kept in distance from all the
personnel and shall not be used or used with any other transmitter. The end user and the installer must provide antenna installation instructions and transmitter operating conditions to meet the requirements for rf exposure compliance -
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
televison reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-
* Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by
reauthorized modifications to this equipment. Such modifications could void
the user authority to operate the equipment.
CAUTION
Risk of explosion if the battery is replaced an incorrect disposal of a
battery into fire or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion; leaving a battery in an extremely
high temperature surrounding environment that can result in an explosion or
the leakage of flammable liquid or gas; battery
subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas
-
ISED Compliance Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. -
This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with I C R SS-102 radiation exposure limits set forth for an uncontrolled environment.
RF Exposure Compliance
This equipment complies with FCC/ISED radiation exposure limits set forth for
an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
These requirements set a SAR limit of 4 W/kg averaged per ten gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the limbs.
CE SAR statement
This equipment complies with Directive 2014/53/EU radiation exposure limits
set forth for an uncontrolled
environment. End user must follow the specific operating instructions for
satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio
waves established by European
Union market(France). These requirements set a SAR limit of 4W/kg averaged
over ten gram of tissue. The highest
SAR value 1.95W/kg reported under this standard during product certification
for use when properly worn on the limbs.
Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.
www.flysky-cn.com
Copyright ©2024 Flysky Technology Co., Ltd.
Release date: 2024-04-15
FCC ID: 2A2UNNB4PRO00
IC: 25584-NB4PRO00
EU importers: Robitronic Electronic Ges.m.b.H
Importer’s address： Pfarrgasse 50
1230 Vienna
Austria
Manufacturer: ShenZhen FLYSKY Technology Co., Ltd.
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District,
Shenzhen, Guangdong, China
