FLYSKY FS-R11P-BT-BS Digital Proportional Radio Control System User Guide
- June 1, 2024
- Flysky
Table of Contents
FLYSKY FS-R11P-BT-BS Digital Proportional Radio Control System
Product Information
Specifications
- Model: FS-MG11-BT-BS & FS-R11P-BT-BS
- FCC ID: 2A2UNMG11OO
- Release Date: 2024-01-16
Product Usage Instructions
The transmitter features various controls and indicators including CH6 Toggle Switch, Neck Strap Hook, Steering Wheel, Throttle Trigger, Handle, Battery Compartment, USB Type-C Port, LCD Display, and more.
- Open the battery compartment cover.
- Insert 4 fully-charged AA batteries into the compartment.
- Ensure correct polarity and replace the cover.
- Open the battery compartment cover.
- Insert the 2S LiPo battery into the compartment.
- Connect the wiring to the JST Jack carefully specific button.
FAQ
- Q: How can I troubleshoot if my transmitter is not powering on?
- A: Ensure that the batteries are correctly installed and fully charged. Check the power switch position and try toggling it a few times. If the issue persists, contact customer service for assistance.
- Q: Can I use rechargeable AA batteries with the transmitter?
- A: Yes, you can use rechargeable AA batteries as long as they are fully charged and meet the specified voltage requirements. Follow the instructions provided for battery installation.
Thank you for purchasing the products of Flysky! To find out more about our products, visit our website at www.flysky-cn.com. If you encounter any problems during use, please refer to the manual first. If the problem is still not resolved, consult your local dealer directly or contact the customer service staff via Flysky’s official website.
Precautions
Read the safety messages listed below before operation!
- Do not use the product at night or during bad weather conditions, like rain or thunderstorms. It can cause erratic operation or loss of control.
- Do not use the product when visibility is limited.
- Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may cause erratic operation or loss of control.
- Interference may cause a loss of control. To ensure the safety of you and others, do not operate in the following places:
- Do not use this product when you are tired, uncomfortable, or under the influence of alcohol or drugs. Doing so may cause serious injury to yourself or others.
- The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large can block the RF signal and lead to loss of control.
- Never grip the transmitter antenna during operation. It significantly degrades signal quality and strength and may cause loss of control.
- Do not touch any part of the model that may generate heat during operation, or immediately after use. The engine, motor or speed control, may be very hot and can cause serious burns.
- Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equipment, read this manual and follow the instructions carefully.
- Make sure the product is properly installed in your model. Failure to do so may result in serious injury.
- Ensure that all servos operate in the correct direction. If not, adjust the direction first.
- Make sure that the model stays within range to prevent loss of control.
- The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
CAUTION!
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
Transmitter Overview
Basic Operations
Installing the AA Battery
Follow the steps below to install the AA batteries:
- Open the battery compartment cover as illustrated.
- Insert 4 fully-charged AA batteries into the compartment. Make sure that the batteries are well set according to the polarities marked on the battery compartment.
- Replace the battery compartment cover.
- Don’t overcharge or overdischarge the LiPo battery.
- Read the instructions of the LiPo battery carefully before use.
Installing the LiPo Battery
Follow the steps below to install the LiPo battery:
- Open the battery compartment cover.
- Insert 2S LiPo battery into the compartment.
- Plug the wiring of the LiPo battery into the JST Jack.
- Replace the battery compartment cover. Be careful not to pinch the cable.
Powering On
Follow the steps below to turn on the transmitter:
- Check to make sure that the batteries are fully charged and installed correctly.
- Toggle the Power Switch to the ON position. The ambient light will be on for 3 seconds and then will be off.
Binding
The transmitter and the receiver have been pre-bound before delivery. If you
are going to use another receiver, follow the steps below to rebind. The
transmitter supports two-way binding, the steps are as follows:
- Turn on the transmitter while holding, and then the transmitter will enter the binding mode. At this time, the LCD display will show “BINDING… “. Once in binding mode release the button.
- Turn on the receiver, and it will wait for 1 second for connection. If without connection, the receiver will enter the binding mode automatically. At this time, the receiver LED will be flashing fast.
- Once the binding is successful, the receiver LED and the Ambient Light of the transmitter will be solid.
- Verify that the transmitter and the receiver are working properly. If you need to re-bind, repeat the above steps.
Note: Applicable to the FS-MG11-BT-BS transmitter and the FS-R11P-BT-BS
receiver; The FS-MG11-BT-BS transmitter complies with the 2A-BS protocol and
is only compatible with receivers conforming to this protocol; Different
receivers have different binding procedures.
For more information, visit FLYSKY’s official website for manuals and other
related information.
Stick Calibration
Use this function to correct for the mechanical deviation of the throttle trigger, steering wheel and CH5 knob, for example, if deviation occurred in the self-centring or maximum minimum travel, the steps are as follows:
- Turn and hold the steering wheel clockwise to the max travel point and push the throttle trigger forward as far as possible, at the same time turn on the transmitter, then press to enter calibration mode, the buzzer will sound three times cyclically.
- Steering Wheel Calibration: Turn the steering wheel to the max and min travel point clockwise/counterclockwise respectively, and the buzzer will sound two times cyclically.
- Throttle Trigger Calibration: Push/pull the throttle trigger to forward/backward as far as it will go, and the buzzer will sound once cyclically.
- CH5 Knob Calibration: Turn the CH5 knob to its max and min travel point clockwise/ counter-clockwise respectively, and the buzzer will give a long beep.
- Press to save and exit in case of the calibration is successful, and the buzzer will give a long beep.
If the calibration fails, pressing the button is invalid. Repeat the steps above.
Failsafe
The function is used to protect the model and personnel when the receiver is
out of control.
It can be set at the transmitter side. By default, it is not set, and the PWM
interfaces will maintain the last output in case of out-of-control. The
setting steps are as follows:
- Press to access the menu, then select F.SAFE using- or+ and press Enter to enter.
- Select a channel you want to set by using- or+ and press to confirm.
- Put the control corresponding to the channel to be configured with failsafe to the preset position, and meanwhile press to confirm.
- Press to exit.
Powering Off
Follow the steps below to turn off the transmitter:
- Turn off the receiver first.
- Toggle the transmitter’s Power Switch to the OFF position to turn off the transmitter.
Make sure to power off the receiver before turning off the transmitter. Failure to do so can result out of control. The unreasonable setting of the Failsafe may cause an accident.
Specifications
- Product Model: FS-MG11-BT-BS
- Compatible Receivers: FS-R11P-BT-BS, FS-R11D-ESC-BS, FS-R11P-BS
- Compatible Models: Car
- Number of Channels: 11
- RF: 2.4GHz ISM
- Maximum Power: <20dBm (e.i.r.p.) （EU)
- 2.4G Protocol: 2A-BS
- Resolution: 4096
- Input Power: 1.5AA*4 or 2S Lipo
- Working Current: About 60mA/6V
- Low Voltage Alarm: Yes
- Antenna: Single Built-in Antenna
- Charging Jack: None (The USB Type-C port is only used for power supply.)
- Online Update: Yes
- Data Output: None
- Distance: ﹥ 150m(Ground Distance Without Interference)
- Temperature Range: -10℃ ~ +60℃
- Humidity Range: 20% ~ 95％
- Dimensions: 135.7189.182.7mm
- Weight: 236g
- Color: Black
- Certifications: CE, FCC ID: 2A2UNMG11OO
Certifications
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used under the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology Co., Ltd.] declares that the Radio Equipment [ FS-
MG11-BT-BS&FS-R11P-BT-BS] complies with RED 2014/53/EU. The full text of the
EU DoC is available at the following internet address:
www.flyskytech.com/info_detail/10.html.
RF Exposure Compliance
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is free. The owner of old appliances is
responsible for bringing the appliances to these collection points or similar
collection points. With this little personal effort, you contribute to
recycling valuable raw materials and the treatment of toxic substances.
CONTACT
- Manufacturer: ShenZhen FLYSKY Technology Co., Ltd.
- Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
- http://www.flysky-cn.com
- Copyright © 2024 Flysky Technology Co., Ltd.
- Release date: 2024-01-16
Figures and illustrations in this manual are provided for reference only and may differ from the actual product appearance. Product design and specifications may be changed without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>