FLYSKY FMS-R7A Receiver User Manual
- June 4, 2024
- Flysky
Table of Contents
FLYSKY FMS-R7A Receiver
Overview
- Motor line
- Battery line
- Switch line
- Antenna
- Left turn signal light + Right turn signal light
- Fog light
- Fog light
- Headlight + Right turn signal light
- Headlight + Left turn signal light
- CH6
- CH4
- CH4
- CH6
- CH1
- CH4
- Fog light + Brake light + Backup light
- CH7
Turn on/off the receiver:
Toggle the button ON/OFF. Self-check display: All car lights will be on for 1S
when the receiver is powered on. Binding: When the receiver is powered on and
waits for 1 second, it will automatically enter the binding state, and the
receiver LED is solid on. If the binding is not completed within 10s or the
receiver is not connected with the transmitter, the LED of the receiver will
enter its slow flashing state.
Channels
- CH1: For Front wheel steering servo
- CH3: For Speed shift servo
- CH4: For Drive switching servo
- CH5: For Back wheel steering servo
- CH6: For Front and Back differential lock
- CH6: For Winch servo
Protection
- When the receiver voltage is lower than 6.4V, all channels have no output. All car lights flash slowly for prompt;
- When the temperature of the receiver is detected to exceed 110℃, the motor of the CH2 has no output, and the other channels output normally. And the normal output will be restored when the temperature is lower than 70℃.
Car light control
- The car light mode is mainly to implement the value of CH1 and CH4, refer to the table below for details.
Car light| Default mode
Always off
| Mode A
The turn signal light is in
| Mode B
a slow flashing
| Mode C
In continuous low-
| Mode D
The turn signal light is in a
---|---|---|---|---|---
Left light|
Always off
| state when the model car makes a left turn.
The turn signal light is in a slow flashing
| light state
In continuous low-
| slow flashing state when the model car makes a left turn.
The turn signal light is in a
Right light|
Always off
| state when the model car makes a right turn.
Solid ON(low-light) Solid ON(High-light)
| light state| slow flashing state when the model car makes a right turn.
Always off
Headlight|
When braking, the brake light is
|
When braking, the break
|
e light is in a high-light state, and when
|
When braking, the brake
Brake light| in a high-light state, and when not braking, it is in an off state.
The backup light is in a high-light
| not braking, it is in a low-light state.
state when the model car backs up; otherwise, it is in the off state.
| light is in a high-light state, and when not braking, it is in an off state.
Backup light|
Always off Solid ON
Frog light| |
2. There are five modes for car light mode. To switch the mode by pressing the CH4 button of the transmitter, the mode is switched in a cycle.
3. Every time the receiver is turned on, the car light control mode is in Default Mode.
Attention
- Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
- Please carefully check each power device and car frame instructions to ensure the power matching is reasonable before use. Avoid damaging the power system due to incorrect matching.
- Do not let the external temperature of the system exceed 90℃ /194 ℉, because high temperature will damage the power system.
- Make sure the receiver’s battery is disconnected before turning off the transmitter, failure to do so can result out of control. The unreasonable setting of the Failsafe may cause accidents.
- After use, remember to disconnect the battery and the ESC. If the battery isn’t disconnected, the ESC will consume electric energy all the time even if it is off. It will discharge completely if connect to the battery for a long time, thus resulting in the failure of the battery or the ESC. We are not responsible for any damage caused by this!
- Make sure the receiver is mounted away from motors or any device that emits excessive electrical noise.
- Keep the antenna of the receiver at least 1cm away from conductive materials such as carbon or metal.
- Do not power on the receiver during the setup process to prevent loss of control.
Certification
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FMS-
R7A] is in compliance with RED 2014/53/EU. The full text of the EU DoC is
available at the following internet address: www.flysky-cn.com.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances
is responsible to bring the appliances to these collecting points or to
similar collection points. With this little personal effort, you contribute to
recycling valuable raw materials and the treatment of toxic substances.
IC STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt RSS
(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Manufacturer: ShenZhen FLYSKY Technology Co., Ltd
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District,
Shenzhen, Guangdong, China
http://www.flysky-cn.com
Copyright © 2022 Flysky Technology co., ltd
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>