evolur 254 Zoodle 2 in 1 Convertible Baby High Chair Owner’s Manual

: June 17, 2024
: evolur

Table of Contents

SAFE SLEEP TIPS
THANK YOU
LIMITED WARRANTY
WARNINGS
PARTS
HARDWARE
HIGH CHAIR ASSEMBLY
HARNESS ASSEMBLY
JUNIOR CHAIR ASSEMBLY
CARE AND MAINTENANCE
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

evolur 254 Zoodle 2 in 1 Convertible Baby High Chair

evolur 254 Zoodle 2 in 1 Convertible Baby High Chair

Read all instructions before assembling and using product.
IMPORTANT – Keep Instructions for future use.

SAFE SLEEP TIPS

Adult Assembly Required.
DO NOT use the product if it is damaged, broken, and/or components are missing or broken.
Do Not Use Power Drills or Drivers.
Small parts may present choking hazard prior to assembly.
Please read the instructions thoroughly. Identify all parts & hardware.
To protect your parts during assembly please place them on a soft surface.
To clean surface, use only water on a damp cloth. Do not use window cleaner or cleaning abrasive as it will scratch the surface and could damage the protective coating.

THANK YOU

THANK YOU …. for choosing Evolur and congratulations on joining our family; a family that has been transforming lives for over 30 years! We appreciate your feedback and wish you the very best in the coming years with your new addition. If you have any questions or concerns please don’t hesitate to reach out to us. One of our trusted Customer Care representatives will be happy to assist you. Thank you again for entrusting us to provide you with safe and affordable baby products and accessories.

LIMITED WARRANTY

Evolur warrants its product to be free from defects in material and workmanship and agrees to remedy any such defect.
This warranty covers 1 year from the date of original purchase.
This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture components and no assembly labor is included.
This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse or which has been altered or repaired in any way.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

WARNINGS

Failure to follow these warnings and the instructions could result in serious injury or death.

PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFETY OF YOUR CHILD.

FALL HAZARD: Children have suffered severe head injuries including skull fractures when falling from high chairs. Falls can happen suddenly if child is not restrained properly.

Always use restraints. Adjust to fit snuggly.
Tray is not designed to hold child in chair.
Stay near and watch child during use.
Prevent serious injury or death from falls or sliding out! Ensure that the harness is fitted correctly and that the child is secure in the harness.
The highchair is suitable for children 6 months to 36 months while using it in highchair position. Highchair is not suitable for children under 6 months. While using this product in the Junior Chair position, it is suitable for children from 24-60 months.
Do not use if any part is broken, torn or missing.
Discontinue use of this highchair when child weighs more than 33 lbs.
Do not use the highchair unless all components are correctly fitted and adjusted.
Do not leave your child unattended, even for the shortest time.
Avoid placing the chair near naked heat sources such as electric bar fires, gas fires, etc, or where a child could gain access to any other kind of hazard.
Ensure that all users are familiar with the product’s operation. It should always assemble and operate easy. If it does not, do not force the mechanism. Rather, stop and read the instructions.
Highchair is recommended to be used on flat stable surfaces.
Please ensure that your Evolur Highchair is fully assembled before using.
Do not move, recline, or adjust the height of this product with child in it.
Never leave child unattended. Always keep your child in view. STRANGULATION HAZARD:
Do not place product in any location where there are cords, such as window blind cords, drapes, phone cords, etc.
FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY as this product is intended to be assembled once. If you experience any difficulties, please contact the Customer Service Department
All additional hazards such as electrical flexes should be kept out of reach of your child when in the highchair.
Assemble the chair once only, it is not intended to be taken apart and reassembled.
PREVENT SERIOUS INJURY OR DEATH FROM SLIDING OUT, FALLS, OR TIPPING OVER. Always use seat belt. Secure your child at all times with the restraint system provided, either in the reclining or upright position. The tray is not designed to hold your child in the product. It is recommended that the product be used in the upright position only by children capable of sitting upright unassisted.
The child should be secured in the highchair at all times using the restraining system.
It is recommended that the highchair be used only by children capable of sitting upright unassisted.
THIS PRODUCT IS DESIGNED AS A highchair for use with child up to 3 years of age or as an infant feeding booster seat for use with a child up to 6 years of age and up to 60 lbs (27.3kg)
ALWAYS USE booster straps to attach infant/toddler feeding booster seat to any chair. Always ensure straps are pulled tight.
THIS INFANT/TODDLER FEEDING BOOSTER SEAT is designed to be used by a child up to 6.

PARTS

If there are any missing parts, please contact Evolur before using the product.

Seat with Harness
Tray with Insert
Metal Cross Base
Front Leg (x2)
Front Leg for Junior Chair (X2)
Upper Footrest
Rear Leg (x2)
Rear Leg For Junior Chair (X2)
Lower Footrest

HARDWARE

If there are any missing parts, please contact Evolur before using the product.

A Bolt M6X50 mm (×4)
B Bolt M6X30 mm (×4)
C Foot (×4)
D Footrest Bolt (x4)
E Washer (×8)
F Allen Key

HIGH CHAIR ASSEMBLY

LEGS ASSEMBLY

1. Place the parts to be assembled on a soft and horizontal surface.
1b. Align the slot in the Front Leg (4) to the Metal Cross Base (3) as shown in the illustration. NOTE: The long side of the metal cross base is for the front leg assembly.
1c. Align the Washer (E) followed by the Bolt (B) in the insertions provided on the front leg to fix the leg to the cross base.
1d. Align the slot in the Rear Leg (7) to the Metal Cross Base (3) as shown in the illustration. NOTE: The short side of the metal cross base is for the rear leg assembly.
1e. Align the Washer (E) followed by the Bolt (B) in the insertions provided on the rear leg to fix the leg to the cross base.
1f. Tighten the bolts with the Allen Key (F) provided. Once fixed, the assembled legs should resemble the second illustration.
High Chair Assembly - Legs Assembly

B Bolt M6X30 mm (×4) Bolt M6X30 mm (×4)

Hardware

E Washer (×4)

FOOTREST ASSEMBLY

2a. Align the extensions of the Upper Footrest (6) to the top insertions on the front legs as shown in the illustration.
2b. Align and insert the Footrest Bolts (D) to the insertions provided on the upper footrest to fix it to the legs.
2c. Similarly, align the extensions of the Lower Footrest (9) to the bottom insertions on the front legs. Align and insert the Footrest Bolts (D) to the insertions provided on the lower footrest to fix it to the legs.
2d. Once assembled, the footrests need to resemble the bottom illustration.

Footrest Assembly

D Footrest Bolt (x4)

FOOT ASSEMBLY

3a. Align and screw the Foot (C) to the bottom of the legs as shown in the illustration.
3b. Each foot can be adjusted by turning counter-clockwise to remove any wobble due to an uneven floor.

Foot Assembly

C Foot (×4)

SEAT ASSEMBLY

4a. Align the extensions on the bottom of the Seat With Harness (1) to the slots at the top of the cross base as shown in the illustration.
4b. Hold the half-assembled highchair upside down. Align the Washer (E) followed by the Bolt (A) in the insertions provided on the cross base to fix the seat to the cross base and legs.
4c. Tighten the bolts with the Allen Key (F) provided.

Seat Assembly

A Bolt M6X50 mm (×4)

Hardware

E Washer (×4)

TRAY ASSEMBLY

5a. As shown in the first illustration, pull both side latches at the bottom of the Tray With Insert (2) to attach it to the highchair. Slide the tray in its slot along the top of the armrest.
5b. Release the latch to secure the tray in your desired position (1 or 2) as shown in the second illustration. Pull the tray towards you to make sure it is securely fixed.
5c. You can remove the tray by locating the three latch points as shown in the third illustration, releasing them, and pulling them upward.

HARNESS ASSEMBLY

6a. Slide the shoulder strap onto the top of the waist strap latch. Repeat for the other side.
6b. Insert the shoulder/waist strap latch assembly into the buckle. Push until you here a click.
6c. Repeat for the other side.

Harness Assembly

6d. To adjust the shoulder and waist straps, slide the strap adjusters as shown in the first illustration.
6e. Press the center buckle to release the harness.
WARNING:
FALL HAZARD: Children have suffered severe head injuries including skull fractures when falling from high chairs. Falls can happen suddenly if the child is not restrained properly.

Harness Assembly

HIGHCHAIR HARNESS REMOVAL

7a. The Harness and Seat Pad can be removed for cleaning.
7b. Fold the end of the harness strap as shown in the illustration.
7c. Pull the webbing through the slot in the Seat and Pad.
7d. To reassemble, repeat the process in reverse. Check that the straps are oriented correctly and are not twisted.

Highchair Harness Removal

JUNIOR CHAIR ASSEMBLY

CONVERSION OF HIGHCHAIR TO JUNIOR CHAIR

1a. Remove the following parts,
i. Harness (Refer above)
ii. Tray (Refer above)
iii. Footrests (Refer above)

Junior Chair Assembly

REMOVAL OF HIGHCHAIR LEGS

2a. Loosen the four Bolts (A) that secure the Seat to the cross brace as shown in the illustration without complete removal of the bolts.
2b. Remove the Bolts (B) that secures each highchair leg and remove all the four highchair legs.

Junior Chair Assembly

LEGS ASSEMBLY

3a. Align the slot in the Front Leg For Junior Chair (5) to the Metal Cross Base (3) as shown in the illustration. NOTE: The long side of the metal cross base is for the front leg assembly.
3b. Align the Washer (E) followed by the Bolt (B) in the insertions provided on the front leg to fix the leg to the cross base.
3c. Align the slot in the Rear Leg For Junior Chair (8) to the Metal Cross Base (3) as shown in the illustration. NOTE: The short side of the metal cross base is for the rear leg assembly.
3d. Align the Washer (E) followed by the Bolt (B) in the insertions provided on the rear leg to fix the leg to the cross base.
3e. Tighten the bolts with the Allen Key (F) provided. Once fixed, the assembled legs should resemble the second illustration.

Junior Chair Assembly

B Bolt M6X30 mm (×4)

Hardware

E Washer (×4)

SEAT ASSEMBLY

4a. Align the extensions on the bottom of the Seat without Harness to the slots at the top of the cross base as shown in the illustration.
4b. Hold the half-assembled junior chair upside down. Align the Washer (E) followed by the Bolt (A) in the insertions provided on the cross base to fix the seat to the cross base and legs.
4c. Tighten the bolts with the Allen Key (F) provided.

Junior Chair Assembly

A Bolt M6X50 mm (×4)

Hardware

E Washer (×4)

FOOT ASSEMBLY

5a. Align and screw the Foot (C) to the bottom of the legs as shown in the illustration.
5b. Each foot can be adjusted by turning counter-clockwise to remove any wobble due to an uneven floor.

Junior Chair Assembly

C Fo t (×4)

CARE AND MAINTENANCE

Occasionally check your product for loose bolts, worn parts, torn material or stitching. Replace or repair the parts as needed.
Use only replacement parts provided by your manufacturer, Evolur.
Do not attempt to refinish or repair any wooden parts.
Keep this product in a cool, dry place. If this product happens to get wet, wipe with a dry cloth and allow to air dry completely.
Excessive exposure to direct sunlight or heat could cause fading of fabric and wood finishes and/or warping of parts.
To clean this product, wipe clean with damp cloth using only household soap and cool water. Do not bleach.
Seat Pad and Harness can be removed from the Seat and washed by hand in cold water, or machine washed on gentle cycle.

HIGHCHAIR TRAY AND TRAY INSERT:

Thoroughly wash the food compartments of the highchair tray and insert tray before use, with mild soap and a clean sponge or cloth.
Surface clean only. Air dry or dry with a clean cloth.

YOU DID IT!

It’s time to make a happy meal time for your little one in this sturdy, multi- tasking and stylish high chair!