ADLER MS 4492 Vacuum Packer Instruction Manual

: June 3, 2024
: ADLER

Table of Contents

MS 4492 Vacuum Packer
DESCRIPTION OF THE DEVICE
CLEANING AND MAINTENANCE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MS 4492 Vacuum Packer
Instruction Manual

MS 4492 Vacuum Packer

|
---|---

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.

Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
The applicable voltage is 220-240V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
.Never use the product with a damaged power cable or if the device was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
Never use the product close to combustibles.
Do not let cord hang over edge of counter or touch hot surfaces.
.Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
Never touch the appliance with wet hands.
Use only the original accessories or recommended by the manufacturer.
Use the device only for its intended purpose. Do not use outside. Protect against moisture.
When using the device, and especially when closing it, pay special attention to your hands – do not put your hands into the sealing elements.
Do not use flammable objects.
The vacuum sealer is not suitable for packing liquids.
The vacuum sealer is intended for home use only.
Protect from moisture.

DESCRIPTION OF THE DEVICE

1. Product type setting / dry (1A) or moist (1B)	2. Seal button
3. Air extraction & sealing button / cancel button	4. Buttons for opening

Tips for ready-made bags or rolls (foil sleeve):

Maximum width: 30 cm
Use only ready-made bags (open on one side) or foil rolls in the form of a sleeve (open on both sides) intended to vacuum sealing (CR 4470.1)

USE OF THE DEVICE
In order to obtain proper welding, the foil should be clean, dry and free of creases in the welding strip (7).
Preparation of a bag from a roll of foil sleeve (open on both sides).

Depending on the size of the products, cut the required length of the bag.
Put the power cord (13) to socket (14) and connect to the power socket. The lamp (1A) will turn on (default setting). 2. Seal one side of the cut sleeve forming the bag:
a). Open the cover, place one side of the cut foil sleeve in the suction surface (6) so that it does not protrude behind the nozzles (10) as shown in the figure A.
b). Close the cover by pressing down on the sides (Fig. B) to hear the “click” sound and press the button (2). The device will automatically turn off after welding is completed.
c). Press both of the release buttons (4) to open the device.

I Air extraction and welding

Put the items in the bag. Open the cover, place the other side (not welded) on the suction surface (6). Close the cover by pressing (Fig. B) to hear the “click” sound.
By pressing the button (1) select the type of product inside of the bag.

“Dry” – dry (1A)
“Moist” – moist (1B) 3. Press the button (3) to start air suction and welding. The device will automatically turn off when welding is finished. 4. Disconnect the left and then the right cover opening buttons (4) first and lift the cover.

II. Extraction of air from external vacuum containers / bags
The set includes a tube (12) for sucking air from vacuum containers

Connect the container (not included) with the suction nozzle (10) using the tube (12) (Fig. C).
Press the button (11). The button will automatically turn off when air extraction is finished.
After air extraction, disconnect the device and the external vacuum container.
NOTE: when extracting air from external vacuum containers, do not close the cover to avoid deformation of the gasket (9).

CLEANING AND MAINTENANCE

Before cleaning, make sure that the device is disconnected to power.
During cleaning, never immerse the appliance in water, only wipe it with a damp cloth.

NOTE: Keep the cover of the device unlocked, when not in use.
Technical specifications:
Welding time : 10 -15 seconds
Vacuum: -0,55 – -0.60 bar
Nominal power: 95W
Voltage: 220-240V ~50/60Hz
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.