DURKOPP ADLER CSM 221 Long Arm Walking Foot Single Needle New Machine Instructions

DURKOPP ADLER CSM 221 Long Arm Walking Foot Single Needle New Machine

Specifications:

• Part Number: 9889 022106 8S
• Components Included:
  • Hand wheel
  • Pulley
  • Belt guard
  • V-belt
  • Machine id
  • Control unit
  • Motor
  • Position generator
  • Support for position generator
  • Installation instructions
  • Grounding kit
  • Motor fixation hexagonal screw, M8X35 (ISO 4014)
  • Washer, R9 (ISO 7094)
  • Washer spring, A8 (DIN 127)
  • Fillister socket head screw M5x12 (ISO 4762)
  • Adjustment Ring

Product Usage Instructions

Removing the former control unit:

Before starting the installation of the new motor package, remove the following components:

• Belt protection on the machine head
• Mounted motor with motor base and belt
• Control unit with all cables (except potential equalization cable from the machine head)
• Set value initiator and its bracket

Mechanical installation of the components:

• Mounting the DAC-Classic:
  Mount the DAC-Classic control unit under the table top on the right front using the provided wood screws. Secure electric cables with strain relief and nail clamps for protection.

• Preventing belt slippage:
  Fit the adjustment ring to prevent the belt from sliding off the pulley when the machine head is tilted. Refit the cover of the belt protection onto the motor and fix the mounting bracket of thesynchronizer on the belt protection of the machine head.

• Mounting the synchronizer:
  Turn the hand wheel towards the operator until the needle tip is close to the throat plate level. Screw the synchronizer onto the hand wheel aligning it with the marking on the synchronizer

FAQ:

Q: Can the conversion to DAC-Classic be done by anyone?
A: No, the conversion should only be carried out by qualified technicians after turning off the main switch and unplugging from the mains.

Components of the kit

Please check before you start the conversion to DAC-Classic, whether all the components of the kit 9889 022106 8S are included in the delivery.

Installation instructions

CAUTION Risk of Injury!
Turn off the main switch and remove the plug from the mains before you start with the conversion.
The conversion may only be carried out by qualified technicians.

Removing the former control unit

Before you start to mount the new motor package, the following components have to be removed first:

• the belt protection on the machine head
• the mounted motor together with motor base and belt
• the control unit with all cables (exception: remove the potential equalization cable only from the control unit, not from the machine head)
• the set value initiator including its bracket

Mechanical installation of the components
Mounting the DAC-Classic

• Mount the DAC-Classic control unit as shown in figure 2 with the delivered wood screws underneath the table top on the right front.
• Fix the electric cables with strain relief and, if needed, nail clamps to protect them from mechanical strain.

Mounting the motor

• Screw the adapter and the rear side of the belt protection onto the motor (mind the cable exiting the motor).
• Then, fix the motor as shown in figure 3 loosely onto the motor base. Upon mounting the motor base underneath the table top, make sure the motor pulley is parallel to the machine head pulley and is positioned in the center of the table cutout for the belt. Consult figure 4.
• Tension the belt when tightening the screw of the motor base (fig. 3 No. 1). After this, refit the belt protection of the machine head.
• In order to prevent the belt from sliding off the pulley when the machine head is tilted, fit the adjustment ring in the position shown in figure 5.
• Then refit the cover of the belt protection onto the motor. At this point, the mounting bracket of the synchronizer can be fixed on the belt protection of the machine head.

Mounting the synchronizer

• Turn the hand wheel in running direction (towards the operator) until the needle tip comes as close as possible to the throat plate level, figure 6.
• Screw the synchronizer onto the hand wheel so that the second stud screw in running direction comes in line with the marking on the synchronizer, figure 7.
• Run the cables, making sure that they will not get in the way of moving parts.

If the machine does not carry out the positioning correctly, the effectuated settings have to be compared with the installation instructions for the synchronizer and, if needed, repeated.

Fixing the machine identification
The machine identification can be placed at the cable duct on the rear table top edge. If you want to fix the machine identification elsewhere, make sure that it does not get in the way of moving parts!

Mounting the set value initiator (foot pedal)

• Fix the enclosed fixation bracket onto the table top as shown in figure 8. The cable of the set value initiator can be attached with the clip of the bracket.
• Attach the connecting rods to the set value initiator and the pedal. Make sure that after mounting the angle between connecting rod and pedal is about 90°, see figure 8.

Electric connection of the components

Connect the cables of the motor, the encoder, the synchronizer, the set value initiator (foot pedal) and the machine id as shown in figure 9. Screw the potential equalization cable of the machine head and the motor cable onto the potential equalization of the control unit.

Initial operation
The control unit may now be connected to the mains. If all previous steps have been carried out as mentioned above, the machine is now ready for operation.

Basic settings of parameters

• The control unit comes with a basic factory setting that allows for sewing without any additional parameter settings needed.
• However, if you should need the parameters you can find them in the Download Area of www.duerkopp-adler.com (number 0791 221900).
• The adjustment of the settings is described in the manual delivered with the sewing drive. This document is also to be found in the Download Area of www.duerkopp-adler.com.

DÜRKOPP ADLER GmbH
Potsdamer Str. 190 D-33719 Bielefeld Germany Phone +49 (0) 521 925 00
E-Mail : service@duerkopp-adler.com
www.duerkopp-adler.com
Subject to design changes – Printed in Germany – Dürkopp Adler GmbH – 0791 221770 EN – 01.0 – 12/2022

References

• adler.com
• Dürkopp Adler

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>