TYROLIT FSE811 Flat Saw User Manual

FSE811 Flat Saw
User Manual

10997619 EN / 10.03.2017

Manufacturer’s address:
TYROLIT Hydrostress AG
Witzbergstrasse 18
CH-8330 Pfäffikon
Switzerland
Tel. +41 44 952 18 18
Fax +41 44 952 18 00
e-mail: info@tyrolit.com
www.hydrostress.com 
TYROLIT Hydrostress AG reserves the right to make technical changes without prior notice.
Copyright © 2014 TYROLIT Hydrostress AG, CH-8330 Pfäffikon ZH, Switzerland
All rights reserved, in particular copyrighting and translating rights.
Printing of this operating manual, including extracts from it, is prohibited. No parts of it may be reproduced in any form or processed using electronic systems, duplicated or  disseminated without the written permission of TYROLIT Hydrostress AG.

Preface to the operating manual

This operating manual makes it easier to become familiar with the machine and to use it properly.
The operating manual contains important information on how to operate the machine safely, properly and efficiently. Following the operating manual helps avoid danger,  reduce repair costs and downtime, and increase the machine’s reliability and life. The operating manual must be supplemented with instructions based on national regulations for accident prevention and environmental protection.
The operating manual must always be readily available at the location where the machine is used.
The operating manual must be read and used by any person assigned tasks with the machine, such as:

• operation, including set-up, repair of malfunctions during operation, disposal of production waste, maintenance, disposal of materials
• maintenance (service, inspection, or repair) and/or
• Transport

In addition to the operating manual and the regulations for accident prevention in force in the country and at the location where the machine is used, recognised technical  rules for safe and correct operation must be followed.

Basic safety instructions

1. 1 Warnings and symbols in this manual
   Danger! Points out that serious or even fatal injuries may result if not followed.
   Caution! Points out that injuries may result if not followed.
   Note
   Points out that damage to the machine or other equipment may result if not followed.

2. Principle of intended use
   1.2.1 The machine has been constructed using the latest technology and in accordance with recognised safety guidelines. Nevertheless, the use of the machine may still  represent a risk of injury or death to the user or third parties, or damage to the machine and other material.
   1.2.2 The machine may only be used when it is in correct working order and for its intended purpose. The operator must follow the instructions in the operating manual  and be fully aware of the safety requirements and hazards posed by the machine! In particular, any faults that may compromise the safety of the machine must be  repaired immediately.
   1.2.3 The flat saw is intended solely for cutting joints in concrete or asphalt. Cutting of wood, plastic or metal (except reinforcements in concrete) is prohibited!
   Any additional or other use is considered improper. The manufacturer/supplier is not liable for damages resulting from improper use.
   Compliance with the operating manual and observation of inspection and service requirements are essential components of proper use.

3. 1.3 Organisational measures
   1.3.1 Always keep the operating manual readily available at the location where the machine is used!
   1.3.2 In addition to the operating manual, observe and instruct the user in all generally applicable legal and other mandatory regulations on accident prevention and environmental protection!
   1.3.3 Personnel assigned to work with the machine must have read the operating instructions and, in particular, the chapter on safety before beginning work. Reading the  manual for the first time when already working on the machine is too late. This applies especially to persons who work on the machine only occasionally, such as those  performing set-up and maintenance.
   1.3.4 Check at least from time to time whether personnel are performing the work in compliance with the operating manual and paying attention to risks and safety  factors!
   1.3.5 Use personal protective equipment where necessary or if required by regulations.
   1.3.6 Obey all safety and danger notices on the machine!
   1.3.7 Ensure that all safety and danger notices on the machine remain clearly legible!
   1.3.8 In the event of safety-relevant changes to the machine or its operating performance, stop the machine immediately and report the malfunction to the responsible  authority/ person!
   1.3.9 Do not make any modifications to the machine, add attachments, or reconfigure it without the supplier’s permission!
   1.3.10 Only use manufacturer’s original parts!
   1.3.11 Observe the stipulated periods or the periods given in the operating manual for inspections!
   1.3.12 Equipment and tools appropriate to the work are absolutely essential for performing maintenance work.

4. 1.4 Personnel selection and qualification
   1.4.1 Only reliable personnel may work with the machine.
   Observe the minimum legal age.
   1.4.2 Use only trained or instructed staff. Clearly establish individual responsibilities for operation, set-up, maintenance and repair!
   1.4.3 Ensure that only assigned personnel work with the machine!
   1.4.4 Specify machine operator responsibilities – including those pertaining to road traffic regulations
   – and authorise the operator to ignore any instructions from third parties that may compromise safety!
   1.4.5 Personnel who are being trained or instructed on the machine or are in a general training program may only be permitted to work on the machine while under the  constant supervision of an experienced person!
   1.4.6 Work on electrical equipment on the machine may only be carried out by an electrician or by instructed persons under the guidance and supervision of an  electrician in accordance with electrical regulations.

5. Safety instructions during specific operating phases
   1.5.1 Normal operation
   1.5.1.1 Avoid all working methods which may compromise safety!
   1.5.1.2 Take steps to ensure that the machine is operated only in a safe and proper condition!
   1.5.1.3 Check the machine for visible external damage and defects at least once per shift!
   Immediately report any changes (including in operational performance) to the responsible department/individual! If necessary, stop the machine immediately and secure  it.
   1.5.1.4 In the case of a fault, stop the machine immediately and make it secure. Immediately repair any faults!
   1.5.1.5 Before starting work, become familiar with the work environment at the location where the machine is used. This includes obstacles in the work and traffic area,  the load-bearing capacity of the surface, required securing of the construction site from the public traffic area and possibilities for help in case of accidents.
   1.5.2 Special work in conjunction with use of the machine and maintenance and repairs during operation; disposal 1.5.2.1 Observe all the setting, maintenance and
   inspection activities and timetables, including instructions for replacing parts/secondary devices, as described in the operating manual!
   Only technically qualified personnel should carry out these activities.
   1.5.2.2 Brief operating personnel before beginning special operations and maintenance work! Appoint supervisory personnel.
   1.5.2.3 If the machine is completely shut down during maintenance and repair work, it must be mechanically secured to prevent accidental activation.
   1.5.2.4 Before cleaning the machine with water or steam jet (high-pressure cleaner) or other cleaning agents, cover/seal all openings that, for reasons of safety and/or  functioning, water/steam/cleaning agents must not be allowed to enter.
   Particularly endangered are electrical motors and switches.
   1.5.2.5 After cleaning, the covers and tapes must be removed completely!
   1.5.2.6 Always tighten loose screw connections during servicing and maintenance work!
   1.5.2.7 Any safety devices removed during set-up, maintenance or repair must be reinstalled and checked immediately upon completion of the maintenance and repair  work!
   1.5.2.8 Dispose of fuel and consumable materials and replacement parts in a safe and environmentally-friendly manner!

6. Notes on specific hazard types
   1.6.1 Electricity
   1.6.1.1 Only use original fuses with the specified amperage! In the electrical power supply is interrupted, shut down the machine immediately!
   1.6.1.2 Work on electrical equipment may only be carried out by electricians or by trained persons under the guidance and supervision of an electrician in accordance  with electrical regulations.
   1.6.1.3 The electrical equipment on the machine should be inspected/checked on a regular basis. Defects, such as loose connections or scorched cables, must be repaired  immediately.
   1.6.2 Dust
   1.6.2.1 Observe applicable national regulations when working in enclosed spaces!
   1.6.3 Noise
   1.6.3.1 Wear required personal hearing protection!

7. 1.7 Transport
   1.7.1 When loading, use only hoists and lifting gear with sufficient capacity!
   1.7.2 Appoint a trained supervisor for the lifting procedure!
   1.7.3 Machines should be lifted with lifting gear correctly in accordance with the specifications in the operating manual (lifting points for load-lifting equipment, etc.)!
   1.7.4 Use only suitable transport vehicles with sufficient lifting capacities!
   1.7.5 Secure the load reliably. Use suitable lifting points!
   1.7.6 Disconnect all power sources before moving the machine, even for very short distances!
   Ensure that the machine is correctly reconnected to the power supply before restarting!
   1.7.7 Restart the machine strictly in accordance with the operating manual!

Machine description

2.1 Overview of components

2.2 Protective equipment

2.3. Technical data

| FSE811
---|---
Cutting depth| 320 mm
Max. saw blade diameter| 800 mm
Saw blade receptacle| 25.4 mm
Dimensions UW/H| 1100/600/980 mm
Weight| 158 kg
Left / right cut| Yes
Motor power| 7.5 kW
Voltage / frequency| 400 V / 50 Hz
Power consumption| 14.6 A
Saw blade speed| 1300 RPM
Protection class| IP55

2.4. Noise characteristics FSE811
Workplace-related continuous sound pressure level for cutting concrete and asphalt (cutting depth 160 mm)= 80 dB(A)
with diamond segment saw blade NBA and NAK Sound power level with the same saw blades and conditions= 96 dB(A)
The workplace-related continuous sound level corresponds to the assessment level in an eight-hour exposition.

ATTENTION!
Hearing protection must be worn when 90 dB(A) is exceeded!

2.5 Handle vibration
Operating condition
Cutting of asphalt
blade diameter 600 mm
cutting depth = 220 mm
Measured vibration severity k in direction

x
2.5 ms-2| y
2.4 ms-2| z
2.6 ms-2
---|---|---

In taking the measurements, the following standards were considered: ISO 5349, DIN ENV 25349, DIN 45671, VDI 2057

Placement in operation

Before you start the flat saw, you must become familiar with its operation.

1. Preparations for start
   – If required, install saw blade (see 5.2 and 5.3)
   – Move the flat saw into position

2. Test direction of rotation of the saw blade
   – Turn star delta switch (item 7) to “star”
   – Press button start (item 6)
   – Turn star delta switch (item 7 to “0”
   – Check the direction of rotation of the saw blade

3. Observe rotation-direction arrow on the hood
   3.3 Change in direction of rotation
   – Turn star delta switch to “0”
   – Remove supply line cable from the plug (item 11)
   – Turn the phases of the plug (item 11) with a screwdriver
   Push black disc inward and turn

4. Test run
   – Turn star delta switch (item 7) to “star”
   – Press button start (item 6)
   – Wait until the motor has reached a uniform speed (uniform sound)
   – Turn the star delta switch (item 7) further to “delta”
   ATTENTION! Is the saw blade adequately supplied with cooling water?
   Guide bar disk and saw blade are over the cut line
   – Attach water hose to the coupling (item 10) and open the valve
   – Slowly initiate downward movement with crank (item 1) – until the saw blade begins to cut
   – Set cutting depth indicator (item 14) to “zero”
   – Dip saw blade down to the desired cutting depth (indicator item 14)
   Turn crank (item 1)
   – Slowly start feed movement
   Caution! – Dry cutting is not permitted
   – Inadequate cooling water results in early wear or malfunctioning of the saw blade

Transport

1. Transport position means:
   – Guide bar is folded up
   – Move saw arm upward until the saw blade has adequate ground clearance
   – Lock spindle with locking bar (item 2)

2. Movement with the crane
   – Observe all points of 4.1
   Attach the crane suspension gear to the rings (item 8)
   ∗ Pay attention to machine weight
   – Lift and set down carefully

Operation

5.1 Normal cutting operation
Attention: The machine may only be operated on electrical circuits protected with ground fault circuit interrupters.

• Adjust feed speed to the cutting depth and the material being worked on
  CAUTION!
  If feed force is too large, the flat saw attempts to “climb” forward

• Ensure there is adequate water on the saw blade (observe point 7, Maintenance)
  ∗ Use only fresh or clean water

5.2 Saw blade replacement

• Raise the saw blade somewhat

• Turn the flat saw completely off

• Unplug feed line

• Loosen the wing screw (item 4)

• Pull the saw hood holder out of the C-rail

• Lift the saw hood upward

• Open the flange nut (right-hand thread)

• Remove saw flange thrust washer and saw blade

• Thoroughly clean the flange’s contact surfaces, if necessary

• Install new saw blade
  ATTENTION! ∗ Rotation direction arrow on the saw blade must match the one on the hood
  ∗ The driving pin on the flange must seat in the driving hole on the saw blade

• Install the saw flange thrust washer and the flange nut
  ATTENTION! ∗ Install the retaining split pin

• Install the saw hood

5.3 Change from right to left cut

• Loosen wing screw (item 4)
• Remove the saw hood (item 5) with rods
• Uncouple the water hose
• With the crank handle (item 1), turn the motor completely downwards
• Remove the eyebolts (item 8)
• With the crank handle (item 1), turn the motor receptacle ca. 8-10 cm upwards
• You can now swivel the motor 180°
• Turn the motor receptacle downward again (item 1)

ATTENTION! Fit screws and pins

• Install eyebolts (item 8)
• Install the water hose fastener (item 10) on the other side

Attention! Turn saw blade (see also 5.2)

• Install saw hood (item 5) (move rods)
• Change saw blade rotation direction by changing the poles of the plug (item 11) (see also 3.3)

Shut-down

• Turn back star delta switch (item 7) to “0”
• Remove supply line
• Crank saw hood up until the brake presses against the wheel

Maintenance

| Daily| Weekly| Monthly| Semiannually
---|---|---|---|---
Check V-belt (see 8.2)| X| | |
Check screws (item 8) (tightened?)| X| | |
Lubricate the spindle of the cutting depth adjustment (item 1) with spray lubricant| | | X|

All screws must be tightened after ca. 20 hours of operation! V-belts must be tightened after ca. 2 hours of operation!

Repair of malfunctions

replace (see 8.3)
No water on the saw blade| Water supply strainer clogged strainer dirty| Clean water line strainer; flush water supply with pressure (5-8 bar)

8.2 Check the V-belt tension

• Remove protective cap (item 16 )
• With medium force, it should be possible to depress the V-belt by one belt width

8.3 Adjusting the V-belt tension

• Delease excentric screw (item 17)
• Turn he adjustment screw (item 18) as needed
• Tighten the excentric screw (item 17)
• The V-belt can be tightened again on the opposite side.

8.4 Adjustment of the protective motor switch
The protective motor switch in the switch box is to protect the kick-off switch and to trigger the thermo sensing device. The thermo sensing device has to be adjusted to 15  A. The motor is directly protected through the thermo sensing device.

Declaration of conformity
Typenschild hier aufkleben
We declare under our sole responsibility that this product complies with the following directives and standards

Direttiva applicata

Norme applicate
EN ISO 12100:2010
EN 13862/A 1 :2009
EN 60204-1 /A 1 :2009

Fugenschneider FSE811
Flat saw
Scie ~ sol
Tagliagiunti
Cortadora de juntas TYROLIT Hydrostress AG
Witzbergstrasse 18
CH-8330 Pf~ffikon
Switzerland
Pf~ffikon, 07.12.2014

Pascal Schmid
Leiter Entwickluna

References

• Domain im Kundenauftrag registriert

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>