level one DS-2201 Gigabit Ethernet VDSL2 Converter/Extender Installation Guide
- July 4, 2024
- level one
Table of Contents
level one DS-2201 Gigabit Ethernet VDSL2 Converter/Extender
Specifications:
- Model: VDS-2201
- Type: Gigabit Ethernet VDSL2 Converter/Extender
- Input Voltage: 12-24VDC
- Interface:
- 1 x RJ-45 connector for Gigabit Ethernet LAN port
- 1 x RJ-45 connector for VDSL2 port
- LED Indicators: Power status, RT mode activation, LAN port speed and link status, VDSL2 link status
- DIP Switches: 4 switches for configuration
Product Usage Instructions
1. Installation:
Connect the positive and negative wires from a 12-24VDC power source to the V+ and V- contacts on the terminal block. Ensure the wires are securely tightened using the wire-clamp screws.
2. LED Indicators:
The LEDs indicate various statuses:
- PWR (Power): Green when powered on, off when powered off
- RT (Remote): Green when in RT mode, off when in CO mode
- LNK (Link): Green when connected, blinks slowly when idle, blinks fast during training
3. DIP Switch Configuration:
Adjust the DIP switches based on your requirements:
- Switch 1: RT/CO (Remote/Master)
- Switch 2: Asymm/Symm (Asymmetric/Symmetric)
- Switch 3: Mode (Interleave/G.INP)
- Switch 4: SNR (Low/High)
Note: Ensure the power is turned off before making any changes.
4. Wall Mounting:
Wall mounting is supported by specific models. Use two mounting holes at the rear side for horizontal or vertical wall mounting. Ensure the screw length does not exceed 3mm inside the device body.
FAQ
- Q: What is the default setting of DIP switch 1?
- A: The factory default setting of switch 1 is ON.
- Q: How do I know the link status for VDSL2?
- A: The LED indicator on the front panel will show the VDSL2 link status.
- Q: Can I use a power source outside the 12-24VDC range?
- A: It is recommended to use a power source within the specified range to avoid damage to the device.
Quick Installation Guide
Front Panel Illustration
The following interfaces are placed on the front panel:
- 1 x RJ-45 connector for Gigabit Ethernet LAN port
- 1 x RJ-45 connector for VDSL2 port
- 3 x LEDs for LAN port speed and link status
- 1 x LED for power status
- 1 x LED for RT mode activation
- 1 x LED for VDSL2 link status
- 4 DIP Switches for CFG (Configuration)
LED Indicators
LEDs on the right
| LED | Color | Blink | On | Off |
|---|---|---|---|---|
| PWR | Green | N/A | Device Power On | Power Off |
| RT | Green | N/A | RT |
(Remote)
| CO
(Master)
LNK
| ****
Green
| Slow: Idle| ****
VDSL2 LINK UP
| VDSL2 LINK DOWN
Fast: Training
LEDs on the left
| LED | Color | Blink | On | Off |
|---|---|---|---|---|
| 10 | Green | Data Transmitting | 10Mbps | LINK DOWN |
| 100 | Green | Data Transmitting | 100Mbps | LINK DOWN |
| 1000 | Green | Data Transmitting | 1000Mbps | LINK DOWN |
DIP Switch Configuration
DIP
Switch
| Function| On| Off
---|---|---|---
1| RT/CO| RT| CO
2| Asymm/Symm| Asymmetric| Symmetric
3| Mode| Interleave| G.INP
4| SNR| Low| High
Input from Terminal Block range 12 ~ 24VDC Insert the positive and negative
wires into V+ and V- contacts on the terminal block and tighten the wire-clamp
screws to prevent the wires from being loosened.
LINE Port Pin Assignments
Two of the eight pins of VDSL2 port are used to connect UTP cable over long
distances, pin-out assignments are shown in the table below.
Wall Mounting
Wall mounting is only supported by 108MI and 108MI-TB.
- At the rear side, two mounting holes are placed for horizontal or vertical wall mounting.
- The length of the screw head and body, must not be longer than 3mm inside the device body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>