maytronics Triton PS Robotic Pool Cleaner User Guide

maytronics Triton PS Robotic Pool Cleaner

Thank you!

Thank you for purchasing a Maytronics Robotic Pool Cleaner.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.

Cautions & Warnings

• Use the originally supplied power supply only.
• Do not use an extension cable in any case whatsoever.
• Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter.
• Keep the power supply out of standing water.
• Do not enter the pool while the Pool Cleaner is working.
• Unplug the power supply before servicing.
• Do not use the cable to take the pool cleaner out of the water.
• Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -34°C (43-93°F); NaCl Maximum = 5000 ppm.

Digital Power Supply Input: 220-240 AC Volts 50-60 Hertz 720 Watt
output: <30 voe IP 54

Specifications:

Motor protection: IP68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/ 76.4ft

Helpful hints

• When working, the Power Supply should be placed in the shade.

• If the Dolphin is fitted with combined or wonder brushes, gently squeeze the brushes until they are soaked with water.

• Release minimal required floating cable length to ensure proper pool coverage.
  Leave excess cable rolled outside the pool.

• After each cleaning cycle wash the filters or cartridge. Clogged filters reduce scanning and cleaning efficiency.

• To remove the kinks stretch the cable out completely and let it sit for at least a day in the sun.

• Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.

Robot Operation

1. Set Up
   Attach the floating cable to the power supply.
   
   Position the power supply at least 3m/1 Oft away from the edge of the pool.
   

2. Into the pool
   Put the Pool Cleaner into the pool.
   Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
   

3. Operation
   Turn the power supply O N.
   The Pool Cleaner will now operate until it has reached the end of the cleaning cycle.
   

4. Out of the pool
   
   

5. Cleaning the filter
   It is highly recommended to clean the filter basket after each cleaning cycle.
   Note: Don’t let the filter cartridges dry out before cleaning.
   Unplug the power supply before servicing
   Open the filter cover.

Lift up the basket.

Open the latch to release the bottom lid in order to remove the debris.

Clean the filter basket with a hose

6. Storage
   Coil the cable and store in a cool, dry place on the Caddy.
   Do NOT store the robot where it will be exposed to direct sunlight, excessive heat or to frost.
   

Maintenance

Periodic filter cleaning

Dismantle the 4 ultra-fine filter panels of the outer basket according to the following steps:

1. Dismantle the panels, starting with pressing on panel no.1 using your thumbs.
   

2. Continue to dismantle the panels in the order of their numbers: no.2–> no.3–> no. 4.

Cleaning the impeller

If you notice debris trapped in the impeller:

Unplug the power supply before servicing Clean the debris trapped in the impeller opening, according to the following steps:

CUSTOMER SERVICES

For online product warranty registration:
registration.maytronics.com
www.maytronics.com
For a detailed manual (including videos): manuals.maytronics.com/en/
99996207-US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>