Mounting Dream MD2295 Full Motion TV Wall Mount TV Bracket Instruction Manual

Mounting Dream MD2295 Full Motion TV Wall Mount TV Bracket

• Please read this instruction carefully before installation.
• Fits for most 42-70 inches Plasma, LCD and LED TVs.
• Weight capacity : 35.5 kg (78 LBS).

Safety Warning : Thank you for choosing Mounting Dream TV mount. For safe application of model MD2295, and preventing yourself or others from danger or property loss, please read through this manual before use. If you do not understand these instructions or have any doubt over safety of installation, please contact qualified contractor or Mounting Dream customer service. Please check carefully before assembly to ensure no parts missed or damaged. Our customer service representative will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts purchased through authorized distributor will be delivered to your door. Please do not use defective parts. Incorrect installation may result in product damage or body injury. Do not apply this product to  any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse

**Before getting started, let’s make sure this mount is perfect for

you**

1. Is your TV VESA equal to/greater than 200x100mm/8x4in and equal to /less than VESA 600x400mm/24×16″?
2. Does your TV (including accessories) weigh more than 78 lbs (35.5kg)?
3. What is your wall made of?

Installation tools

Gifts

Part list

Wall mounting and TV bracket assembly hardware

TV mounting hardware

Concrete wall anchor (NOT INCLUDED)

1. Assemble extension arms ( 7,8 ) as picture shows, align the extension arm holes with the wall plate unit, then fasten it with bolt 3 by using Allen key 2.

2. Wall plate installation
   Wall plate installation in wood stud To avoid potential body injury or property damage:

3. Wall mount must be installed into wood stud’s center, not drywall alone.

4. Drywall covering the wood stud must not exceed 16 mm (5/8 in.).

5. Minimum wood stud size: common 2 x 4 in(51 x 102 mm). Nominal 1 1/2 x 3 1/2 in(38 x 89mm)

6. The wall must be capable of supporting five times the weight of TV plus mount.

7. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.

8. All lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate. Ensure the wall plate is securely fastened to the wall before continuing on to the next step. Failure to follow this instruction will possibly lead to TV falling off from wall, and would possibly cause body injuries or property loss.
   Make sure the BOLT HEAD on the wall plate is upward Take down the Mounting template, put 4 lag bolts 1 into the drilled holes, and tighten each bolt by using a socket wrench to mount the wall plate securely. Before totally tightening the lag bolt please attach the bubble level on the wall plate to check whether it is level

9. Wall plate installation on concrete wall
   To avoid potential personal injury or property damage:

10. Make sure the BOLT HEAD on the wall plate is upward as the picture shows.

11. Solid concrete wall’s thickness should be more than 100mm/4″, and the wall must be capable of supporting five times the weight of the TV plus the mount.

12. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate. Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
    

13. Select TV hardware (diameter / length / combination)

14. Bolt diameter : hand thread bolts into threaded inserts on the back of TV to determine correct bolt diameter (M4, M5, M6, M8).

15. Bolt length : verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns

16. Too short will not hold the TV.

17. Too long will damage the TV

18. Bolt and spacer combination: spacers sometimes are needed to combine with bolts for several situations.
    (For detail bolts and spacers combination, please refer to Page 7) Carefully lay your TV on a non-abrasive surface, or lay it with a padding underneath
    it so as not to damage the screen

19. Attach brackets to the back of the TV
    For the TV with flat back, mount the brackets with bolt/washer/spacer combination.
    Tips:

20. Make sure the ends of TV brackets with round holes are facing upward.

21. Round hole is for upper VESA hole, and long slot hole for lower VESA hole. Please try best to locate brackets symmetrically (top & bottom) at the back of TV to avoid brackets stick out.

22. Attention : Screw in bolts a bit, then pull upward brackets to reduce the gap between bolts and bolt holes to make two brackets parallel. Then fasten bolts.
    Bolt/spacer/washer combination options (only for reference)
    Carefully lay TV on a non-abrasive surface, or with a padding underneath it so as not to damage the screen.

23. For TV with inset mounting holes, mount the brackets with bolt/washer/spacer combination.  (Spacers are highly recommended to be added, thus enlarge the space between TV and brackets for better functionality.)
    Tips:

24. Make sure the ends of TV brackets with round  holes are facing upward.

25. Round hole is for upper VESA hole, and long slot hole for lower VESA hole. Please try best to locate brackets symmetrically (top & bottom) at the back of TV to avoid brackets stick out.

26. Attention : Screw in bolts a bit, then pull upward brackets to reduce the gap between bolts and bolt holes to make two brackets parallel. Then fasten bolts.
    Bolt/spacer/washer combination options (only for reference) Tips : You have to remove the inner circle of 2.5mm washer (j) in order to fit the M6 (e) or M8 (f) bolt. Carefully lay TV on a non-abrasive surface, or with a padding underneath it so as not to damage the screen

27. Hang the pre-assembled TV unit onto the horizontal bars of the wall plate unit.

28. Fasten the tube clips with brackets by using bolts 4 with a screwdriver.

29. Make sure the TV unit is horizontal, you can adjust the TV plate a little bit (+/-3 degrees) to level the TV, then fasten TV plate by leveling bolts with Allen key 2
    Tip: If TV still not level after adjustment, please loosen bolts a bit, hold TV to adjust to level, then fasten bolts securely with Allen key

30. Adjust the tilting angle with spring loaded handle: Hold the TV and adjust it to your desired position, and fasten the handle and the bolt opposite to the handle
    To fasten the handle:

31. Turn handle clockwise until stopped by mount.

32. Pull out the handle

33. While holding handle away from mount, turn it counterclockwise

34. Push and release the handle.

35. Turn handle clockwise to further fasten the mount. Repeat these steps until TV firmly tightened.
    Tips: Keep handle parallel with wall. Handle not parallel with wall may be broke by hitting the wall while TV being pushed back to the wall.
    Adjust the swivel angle:
    Grab TV and slide it to your desired direction.

36. Manage TV cables orderly and tie them with velcro cable ties.

Product dimensions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>