Mounting Dream UL Listed TV Wall Mount Swivel and Tilt for Most 26-55 Inch TV-User Guide

Mounting Dream UL Listed TV Wall Mount Swivel and Tilt for Most 26-55

Inch TV

Specifications

• MOUNTING TYPE: Wall Mount
• MOVEMENT TYPE: Tilt, swivel, leveling
• BRAND: Mounting Dream
• MATERIAL: Alloy Steel
• TV SIZE: 55 Inches
• COLOR: Black
• MINIMUM COMPATIBLE SIZE: 26 Inches
• COMPATIBLE DEVICES: Televisions
• MAXIMUM TILT ANGLE: 15 Degrees
• PRODUCT DIMENSIONS: 17.13 x 16.54 x 3.07 inches
• ITEM WEIGHT: 9 pounds

Introduction

Most 26-55 inch OLED/LED/Plasma TVs up to 60 lbs. can be supported by this TV wall bracket, which has a maximum VESA of 400 x 400mm/mounting hole spacing. Please refer to the product description for further details on whether this TV wall mount matches your TV in terms of VESA, wood stud location, and possibly blocked input.

With a full motion TV wall mount, you can effortlessly adjust the angle and distance of your TV for a comfortable viewing experience: To prevent glare, tilt the TV 5° up and 15° down, and swivel it left or right depending on your seat. Pull out to 17.1″ and retract to 3.1″, allowing your TV to move about. Perfect TV levelling is possible with +/-3° post-installation adjustment.

In pre-labeled bags, you’ll find a TV mount with reasonable instructions and a full range of hardware. Cable ties and a bubble level are also available. If you request it, concrete anchors will be delivered. All of our TV brackets are unable to be put just on walls. Robot welding technology makes the entire TV mounting bracket unit robust and safe. If you have any questions, contact customer care in the United States.

[Amazon Transparency Protected] Verifies the validity of each item and gives you access to detailed information about the product you bought, such as the brand story, product features, and installation instructions.

INSTALLATION TOOLS

GIFTS

PART LIST

INSTALLATION HARDWARE

HARDWARE FOR TV INSTALLATION

INSTALLATION INSTRUCTIONS

To avoid potential personal injury or property damage:

1. Make sure the head of bolt on the wall plate is upward as the picture shows.
2. The wall must be capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.

Ensure the wall plate is securely fastened to the wall before continuing on to the next step.

SELECT THE TV HARDWARE DIAMETER AND LENGTH
Your TV type will help you determine which hardware configuration to use.
Hand thread bolts (a, b, c, d, e, f, g, h) into the threaded inserts on the back of your TV to determine the correct bolt diameter (M4, M5, M6 or M8) and length.

CAUTION
Avoid potential personal injuries and property damage! Verifythat there are adequate threads to secure the plate to the monitor. If youencounter resistance, stop immediately and contact customer service. Usethe combination of shortest bolts and spacers to accommodate your needs. Using hardware that is too long may damage your TV.

ATTACH BRACKETS TO THE BACK OF TV

• For the TV with flat back, mount the wall plate with bolt/washer combination of a+k, b+k, c+1, d.
• For TV with irregular back, mount the wall plate with bolt/washer/spacer combination of e+k+i, f+k+i, g+l+i, h+j/m.

HANG THE PRE-ASSEMBLED TV UNIT ON THE WALL PLATE UNIT, THEN FASTEN THE SAFETY BOLT 1 WITH A SCREWDRIVER.

LEVEL THE MOUNT (±3°):

• Loosen bolts ® to adjust the TV plate, and fasten TV plate by bolts ® with Allen key (J) after adjustment. (Figure 1)
• Tilting angle adjustment (+5°/-15°):
• Pull TV to your desired angle then fasten the two bolts 3 with Allen key (J). (Figure 2)

PRODUCT DIMENSIONS

FAQs

Is it possible to mount a television on wood paneling?
However, if the paneling is 1/4- or 3/8-inch thick, you must place the brackets in front of studs and screw into the studs for support; thin paneling will bow outward under the weight of the TV. The brackets can be mounted anywhere if the paneling is 1/2 inch or thicker.

On a TV mount, where do you put the spacers?
Washers go on the mount side against the bolt head, while spacers go on the TV side. Never use more than one spacer on a single bolt, but if the bolt length necessitates it, a spacer with metal washers is OK.

How do you place TV spacers on the wall?
Place the TV mount spacers between the television and the TV bracket to be fastened to the television to use them. At the back of the television, there are four shallow rectangular holes with screwing holes inside. So, you put a spacer in each of these holes.

Is it possible to mount a television using Velcro?
Our Velcro-Fixed TV Mount is a terrific alternative if you’re searching for a simple, practical, and affordable fixed TV mount. This high-definition TV wall mount is ideal for LED TVs and skinny LCD TVs in the 23″ to 42″ range.

When you can’t find a stud, how do you hang a TV?
One of the simplest ways to hang a TV on the wall without a stud is to use an anchor. They keep the screws from falling out of the holes in the wall or harming the structure. It allows flat-screen TVs to be mounted safely. Simply drill a hole, insert the sleeve, and slide the anchor piece into place.

http://www.mountingdream.com/Manual/MD2377%20Manual.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>