LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch User Guide

: June 4, 2024
: Leviton

LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch

LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch
PRODUCT

FCC COMPLIANCE STATEMENT

The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) This device may not cause harmful interference (ii.) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modiﬁcations not expressly approved by Leviton could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION
Any changes or modiﬁcations not expressly approved by Leviton Manufacturing Co., Inc., could void the user’s authority to operate the equipment.
FCC SUPPLIER’S DECLARATION OF CONFORMITY
Model DN15S Switch is manufactured by Leviton Manufacturing Co., Inc. 201 N. Service Road, Melville, NY 11747. www.leviton.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE AND CO-LOCATION
To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population and uncontrolled exposure, this device shall be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. Also, must not be co-located or operated in conjunction with any other antenna or transmitter.
Copyright and Trademark Information
Decora and Decora Smart are the registered trademarks of Leviton Manufacturing Co., Inc., registered in the U.S., Canada, Mexico and China.
Google and Google Play are trademarks of Google LLC. Alexa, and related logos are trademarks of Amazon.com, Inc. or its afﬁliates. Apple®, Home Kit®, and Siri® are trademarks of Apple Inc., registered in the U.S. and other countries.
Use herein of other third party trademarks, service marks, trade names, brand names and/
or product names are for informational purposes only, are/may be the trademarks of their respective owners; such use is not meant to imply afﬁliation, sponsorship, or endorsement. No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.
Patents covering this product, if any, can be found on Leviton.com/patents.
Leviton Manufacturing Co., Inc.
201 North Service Road, Melville, NY 11747
© 2021 Leviton Manufacturing Co., Inc. All rights reserved.
Speciﬁcations subject to change at any time without notice.

Smart Lighting Control for the Whole Home

LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch 01LEVITON DI-000
-DN15S-02B No Neutral Wire Required Switch 01 See the complete line of My Leviton TM app compatible dimmers, switches, plug-ins, and controllers at leviton.com/decorasmart

Welcome

Leviton’s Decora Smart No-Neutral Switch is the perfect retroﬁt solution, making it easier than ever to install smart lighting control in homes without Neutral wiring. Pair with a Decora Smart Wi-Fi Bridge to control lighting with your voice via Amazon Alexa, Google Assistant, or Apple Siri – or use a smartphone or tablet to control your lighting with the My Leviton app even when you’re away from home.
The Decora Smart No-Neutral Switch looks right at home with your other Decora brand in-wall devices, and features intuitive ON/OFF control.
We are here to help
ONLINE
decorasmartsupport.leviton.com
EMAIL
dssupport@leviton.com
CHAT
www.leviton.com/support
CALL
1-800-824-3005 (USA)
1-800-405-5320 (Canada)

Your switch works with:

General purpose loads up to 15 Amps. For speciﬁc ratings, see the chart below.
Do NOT use your switch with aluminum wire or with metal wall plates.
Installation in metal wall boxes or with metal wall plates may result in poor RF performance.
Additional self-service support options can be found in the My Leviton app or at leviton.com/decorasmart.

LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch
03

RATINGS

Features

Rocker

Press the top to turn the light ON.
Press the bottom to turn the light OFF.
Double press the top to turn ON at max brightness.

Status LED

Illuminates when the lights are OFF, so you can ﬁnd the switch in the dark.
Provides connectivity and device status feedback.
Advanced settings are available in the My Leviton app.

What you need to make it work:

Line, Load, and Earth Ground wires are required.
A Decora Smart Wi-Fi Bridge (MLWSB) installed and connected to a 2.4GHz Wi-Fi network with high-speed internet.
An iOS (12.0 or later) or Android (8.0 or later) mobile device.
NOTE: Make sure Wi-Fi and Bluetooth are enabled on your mobile device.
A My Leviton cloud account
(set up through the My Leviton app).

Before you install

Installation requires electrical knowledge.
If you are unsure of any steps, consult an electrician.
Things to consider:
To control the switch from more than one location, such as in 3-way or multi- way, you can use a wireless DAWSC Anywhere Switch Companion device . Learn more about Companion devices and ﬁnd connection instructions at Leviton.com/decorasmart.
LEVITON DI-000-DN15S-02B No Neutral Wire Required Switch
05

Decora Smart Wi-Fi Bridge

This product requires a MLWSB Decora Smart Wi-Fi Bridge to enable smart features such as My Leviton App control, scenes, schedules, Anywhere Companion connectivity, and integration with smart home services such as voice assistants.
A MLWSB Decora Smart Wi-Fi Bridge provides up to 2,500 sq. ft. of coverage and should be placed within 50 ft. of the Decora Smart No-Neutral Switch.
One MLWSB Decora Smart Wi-Fi Bridge supports up to 25 total devices. Supported devices include:
- DN6HD Dimmer
- DN15S Switch
- DAWDC or DAWSC Anywhere Companions

NOTE: One MLWSB Decora Smart Wi-Fi Bridge supports up to 6 Anywhere Companions paired to associated Decora Smart No-Neutral devices.
Visit Leviton.com/decorasmart for product compatibility updates and MLWSB installation instructions.

Identify your wires

WARNING: TO AVOID FIRE, SHOCK, OR DEATH, turn off power at the circuit breaker.
Check your wall box:

Remove wall plate and disconnect existing switch.
Restore power. Carefully test wires with voltage tester to ﬁnd the Line (Hot) wire.
Turn off power at the circuit breaker.
Mark the wires as shown below.
Quick tip: This product was designed to work without a Neutral wire. Line, Load, and Earth Ground wires are required for installation. If your home does not have a Ground wire available, contact Leviton Technical Support or consult an electrician. If your electrical box contains Neutral wires, you can also use a Decora Smart Wi-Fi 2nd Gen Switch (D215S) to enable smart features, without requiring a Wi-Fi Bridge (MLWSB).

Wire your switch

Single pole installation:

Work on only one connection at a time.
Connect wires as shown using the included wire connectors.

If your wall box contains a different wiring conﬁguration, contact Leviton’s Technical Support team or consult an electrician.

Test and install

Restore power. Status LED should ﬂash GREEN.
After powering on the switch to conﬁrm it is receiving power, turn the power back off again at the breaker prior to completing the installation.
WARNING: Turn off power at the circuit breaker before screwing in your switch.
Gently push wires into wall box. Screw switch to box.

Snap on Decora® wall plate and restore power.
Once power is restored, the status LED will blink GREEN, indicating your device is in Setup mode. See page 15 if your Status LED is not blinking GREEN.
Congratulations!
Your Decora Smart Switch is ready to control your light.

Get the app

To download the app, visit my.leviton.com and select the link or scan the QR code below for your device.

Device setup

The Decora Smart No-Neutral Switch pairs to a Decora Smart Wi-Fi Bridge for connectivity to My Leviton, Apple Home Kit, or both.
Use the My Leviton app to pair your Decora Smart No Neutral Switch (DN15S) to your Wi-Fi Bridge.
For voice control with Amazon Alexa or Google Assistant, you will need to pair your Switch to a MLWSB Wi-Fi Bridge that is enrolled in My Leviton.
For voice control with Siri, you will need to pair your Switch to a MLWSB Wi-Fi Bridge that is added to Home Kit.
See MLWSB Getting Started Guide for additional Wi-Fi Bridge setup details.

Connect your Switch to a Decora Smart Wi-Fi Bridge with My Leviton

Make sure a MLWSB Wi-Fi Bridge is installed within range of the DN15S Switch.
Verify the DN15S Switch is in Setup mode (Status LED should be blinking GREEN).
- If the Status LED is not blinking GREEN, see page 15 for instructions on how to put the device into Setup mode.
Launch the My Leviton app.
Log in or choose “Sign Up” to create a new account.
Follow the instructions on the screen.
Once logged in, tap the “+” in the upper right-hand corner of the screen and select “Add Device”
Follow the app instructions to add your device and connect it to a MLWSB Wi-Fi Bridge.

NOTE: If you are only using Home Kit and do not wish to create a My Leviton account, select “Use with Home Kit Only” on the My Leviton sign-up screen.

Test My Leviton app control

Open the My Leviton app.
Tap icon to turn ON/OFF.

Quick tip
The My Leviton app includes many features such as: scheduling, remote control, Vacation mode, Auto-Shut-Off, room scenes, and activities.

Connect to My Leviton partners (optional)

When connected to a MLWSB Wi-Fi Bridge, your switch can work with Amazon Alexa, Apple Home Kit, Google Assistant, IFTTT, and more.
Visit my.leviton.com for a complete list of compatible smart home products and services.

Tap the menu icon, followed by Integrations. Locate the desired service, select it, and follow instructions.

Pair an Anywhere Companion

Make sure your Wi-Fi Bridge is enrolled to My Leviton and your Decora Smart No-Neutral device is paired to your Wi-Fi Bridge.
Place the Anywhere Companion in Pairing mode by pressing the top rocker 5 times. Its Status LED will blink GREEN.
Place the primary Decora Smart No-Neutral device into Pairing mode by pressing the top rocker 5 times.
The Status LED will ﬂash GREEN/AMBER. The Decora Smart No-Neutral device will be automatically paired to the Anywhere Companion in wireless RF range via the Wi-Fi Bridge. Once paired, the Status LED will quickly ﬂash GREEN to show a successful connection.

Status LED

C OLOR

| ACTIVITY|

STATUS

---|---|---
Green| Flashing| In Setup mode and ready to be added to a Decora Smart Wi-Fi Bridge.
Green or OFF| Solid| Normal operation. Can be conﬁgured in a setup.
Amber| Slow Blink| Device is not connected to the Bridge, but is attempting to reconnect.
Green/ Amber| Alternating Blink| Device is in wireless Anywhere Companion Pairing mode.
Red| Blink| Wireless Anywhere Companion devices have unpaired or are at max. number of paired devices.
Green/ Red/Amber| Alternating Blink| Identify feature triggered from the My Leviton app.

Setup mode

Hold the top rocker for 7 seconds and release when the Status LED turns AMBER.
The Status LED will ﬂash GREEN. The device is now in Setup mode.
To exit Setup mode manually, hold the top rocker for 7 seconds.

Diagnostic light

If your device is not connecting, the Status LED can be used as a diagnostic tool. Press the top of the rocker for at least 2 seconds, but less than 7 seconds, and then release. The Status LED will blink a diagnostic code for 2 seconds.

COLOR	STATUS
Red	Cannot communicate to the Decora Smart Wi-Fi Bridge; Bridge may be out of

range or not powered.
Amber| Not paired to a Decora Smart Wi-Fi Bridge.
Green| Connected to a Decora Smart Wi-Fi Bridge and working properly.

Factory default reset

Hold the top rocker for 14 seconds.
After the ﬁrst 7 seconds, the Status LED will turn AMBER. Continue to hold.
After 7 more seconds, the Status LED will quickly ﬂash RED/AMBER.
Release the top rocker and then the device will reset.

What to do if…

Switch is wired and installed, but the light does not respond

Make sure power has been restored at the circuit breaker.
Verify wiring connections are correct.

When power is applied to the switch, the light is OFF and does not respond:

For proper operation, the switch needs a Line (Hot), Load, and Ground connection.

Not connected or intermittent connection to the Decora Smart Wi-Fi Bridge:

Make sure the MLWSB Wi-Fi Bridge is in range and powered; move the Bridge closer if possible.

Pairing to a different Wi-Fi Bridge:

Make sure the MLWSB Wi-Fi Bridge is in range and powered.
Using the My Leviton app, go to switch’s device settings, select “Reconﬁgure Wireless”, and follow the in-app instructions.

How do I clean my device?

To clean, use a damp cloth with mild soap. Do NOT use disinfecting products, including foggers, sprays, or other types of atomized cleaning agents.

Safety ﬁrst

WARNINGS :

TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
TO AVOID FIRE, PERSONAL INJURY, OR PROPERTY DAMAGE, DO NOT install to control a receptacle.
This product is to be installed and/or used in accordance with electrical codes and regulations.
For indoor use only.
If you are unsure about any part of these instructions, consult an electrician.

CAUTIONS:

Save this instruction sheet. It contains important technical data, along with testing and troubleshooting information, which will be useful after installation is complete.
Recommended minimum wall box depth is 2-3/4 in.
Use this switch with copper or copper-clad wire only.

ADDITIONAL RATINGS:

Purpose of Control: Operating Control
Action Control Type: 1
Pollution Degree: 2
Impulse Voltage: 2500V
Disconnection Type: Micro

Limited 2 Year Warranty & Exclusions
For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty, call 1-800-824-3005.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.