EcoDim Smart Dual Dimmer Switch 2×0-100W LED Eco-Dim.05 Zigbee User Manual
- June 3, 2024
- EcoDim
Table of Contents
Smart Dual Dimmer Switch 2×0-100W
LED Eco-Dim.05 Zigbee
User Manual
Smart Dual Dimmer Switch 2×0-100W LED Eco-Dim.05 Zigbee
√ Zigbee support for both channels
√ Voice support (Amazon Alexa & Google Assistant / Home)
√ Suitable for several home automation apps
√ Built-in protection against overloads and extreme temperatures
√ MCU Update available
√ Suitable for 2×0-100W LED
√ Optimal dimmability & light stability
√ MIN & MAX light adjustment options
√ Installation with provided 2 wires (no neutral wire required)
√ Soft start system
√ Noiseless dimming
√ Suitable for surface-mounted boxes & flush-mounted boxes with screw holes
SPECIFICATIONS
| Input | 220-240V— 50Hz |
|---|---|
| Power(Load) | 2x100W LED/ 2×10-100W Halogen / Incandescent |
| Suitable Load Type | Led-, halogen-, light bulbs |
| Dimming Type | R,C Phase cut |
| Working Temperature | -10 -40°C |
| Operation | Push /Turn button |
| Weight | 83g |
Suitable brands of cover material:
√ Berker by Hager
√ Busch-Jaeger
√ Gira
√ JUNG
√ Kopp
√ Merten by Schneider
√ PEHA
INSTALLATION
Always make sure that the electricity is switched off during installation.
Then connect the wires as indicated in the ’Connection diagram’.
Step 1: Install the dimmer in the mounting box by using the screws.
Step 2: Switch the electricity back on. Switch on the connected lights by
pressing the dimmer shaft. Now adjust the ‘MIN adjustment and MAX adjustment
as described under ‘Min & Max installation’
Step 3: Optionally you may connect the dimmer to your SMART home system as
indicated under the heading “Include to the Zigbee Network”.
Step 4: Place back the cover plate and dimmer knob.
MIN/MAX ADJUSTMENT
For the SMART dimmer to work optimally, you can adjust the lights to the
dimmer with the MIN and MAX adjustment. As soon as you start turning MIN and
MAX adjustment, the dimmer will automatically go to the minimum and maximum
light range.
MIN adjustment: Switch on the lights with the push / turn button. When the
lights are on, insert a screwdriver in MIN and turn to the left. When the
light becomes unsteady, turn slightly back to the right so that the light
remains steady.
MAX adjustment: Switch on the lights with the push / turn button. When the
lights are on, insert a screwdriver in MAX and turn to the right. When the
light becomes unsteady, turn slightly back to the left so that the light
remains steady.
CONNECTING HOME AUTOMATION/APP
Suitable for most home automation / apps:
√ Google Assistant/Google Home
√ Amazon Alexa
√ Philips Hue
√ HOMEY
√ Aeotec SmartThings
√ Trust
√ WINK
√ AduroSmart
OPERATION
- FACTORY RESET
Please note that all configuration parameters will be reset after the device is reset or removed from the network.
INCLUDE TO THE ZIGBEE NETWORK
REMOVE: There are two methods to remove the device from the Zigbee
METHOD 1. From your Zigbee Hub interface, choose to wipe or reset the
device according to the instructions.
METHOD2.
TOUCHLINK: Right channel only), For left channel please see Find and Bind
section
Please note: TouchLink takes effect when both devices have not been added to a
ZigBee network and each device can be connected to a remote control
Step 3. .Bring the remote within 10cm of the smart dimmer and set the remote into TouchLink commissioning.
FIND AND BIND
Step 4. Set the remote into find and bind mode and enable it to find and bind commisioning. Please refer to the manual for instructions.
CAUTION
The installation of the dimmer on 230 V mains power must be carried out by a
qualified specialist in compliance with local regulations. Make sure that the
power supply is switched off during all work.
EcoDim
Dr. Huber Noodtstraat 89 7001DV
Doetinchem Info@ecodim.nl
+31 (0)314 844691
https://www.ecodim.nl/eco-dim07-zigbee-z-wave-smart-led-dimmer.html
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>