EcoDim ECO-DIM.06 Zigbee Plug in Dimmer Zigbee Instruction Manual
- June 1, 2024
- EcoDim
Table of Contents
Manual
Plug in dimmer Zigbee
ECO-DIM.06 Zigbee
ECO-DIM.06 Zigbee Plug in Dimmer Zigbee
Please note
– For indoor use only
– Input voltage should be 220-240V
– The plug dimmer is voltage-free when it is unplugged
– Do not cover when in use
ECO-DIM.06 Zigbee
Input voltage: | 220-240V |
---|---|
Frequency: | 50Hz |
Maximum wattage: | 100W |
Minimum wattage: | 0W |
Dimming technology: | Phase cut-off(Trailing Edge R,C) |
Dimmable led lamps: | 0-100W |
Bulbs with electronic transformers: | 5-150VA |
Halogen and incandescent bulbs: | 5-150VA |
Instructions
- Plug the socket dimmer into the socket
- Now insert the plug of the lamp into the socket dimmer
- Now press the dimmer button of the socket dimmer
- Turn the dimmer knob to be able to dim the lamps
Features
√ Zigbee support
√ Voice support (Amazon Alexa & Google Assistant / Homey)
√ Suitable for several home automation apps
√ Suitable for 0-100W LED
√ Optimal dimmable & light stability
√ MIN light adjustment options
√ Suitable for 90% of all LEDs
√ Soft start system
√ Noiseless dimming
Operation
1) Min. Bright Adjustment.
To ensure the dimmer to work optimally, you can adjust the lights brightness
at min. from the dimmer. 2) Factory Reset Please note:
This procedure should only be used when the primary controller is inoperable.
The entire configuration is reset after the device is reset or removed from the
network.
3) Inclusion to the Zigbee Network
Step 1. Remove the device from a previous Zigbee network if it has
already been added to one, otherwise pairing mode will be fail.
Step 2. From your Zigbee Controller interface, choose to add lighting and
enter the pairing mode. 4) Exclusion from the Zigbee Network
Method 1. From your Zigbee hub interface, choose to delete or reset the
device as instructed.
Method 2. Remove from the Device, see below instructions. 4)
TouchLink
Step 1. If the device is on a ZigBee network, remove the device before
enabling TouchLink.
Step
4. Bring the remote within 10cm of the smart dimmer and set the remote into
TouchLink commissioning.
Step 5. The connected light will blink 10 times when TouchLink succeeds.
Note:
a. When both devices (Dimmer and remote) are not included in the Zigbee
Network, each dimmer can link with one remote max.
b. When both devices are included in the same Zigbee network, each dimmer can
link with max 30 remotes.
c. For Philips Hue Hubs and Amazon Echo Plus, add the remote and device to
network first then touchlink.
5) Find and Bind
Step 1. Make sure the device and remote are added to the same Zigbee
network. Step 4. Make sure the device and remote are
added to the same Zigbee network. Please refer to the manufacturers
instructions on how to set the remote in find and bind mode.
Index- Zigbee Clusters the device supports
-
Input Cluster
– 0x0000: Basic
– 0x0003: Identify
– 0x0004: Groups
– 0x0005: Scenes
– 0x0006: On/off
– 0x0008: Level Control
– 0x0b05: Diagnostics -
Output Cluster
– 0x0019: OTA -
Zigbee codes / Commands
The full list of Z-Wave and Zigbee commands can be found on our website, www.ecodim.nl/downloads-smart-dimmer.
Support Hub/Platform
Suitable for most Zigbee hubs / apps:
√ Homey
√ SmartThings
√ Philips Hue
√ Google Home
√ Amazon Alexa
√ Wink
√ Homee
√ Futurehome
√ Aduro Smart
√ Trust Smart Home
Please refer to Corresponding hub manual /instruction to learn how
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>