EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W User Manual

June 6, 2024
EcoDim

EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W

EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
image

Please Read this manual Carefully before installation. Important!

  • It is dangerous if people without proper training work on an electrical installation!
  • There may be a dangerous voltage at the output of the dimmer!
  • When working on the wiring always switch off the mains voltage. Failure to observe this warning may result in death or seriour injury!
  • Read the instructions carefully. Incorrect installtion may damage the dimmer beyond repair.

EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig1

  • The Dimmer controller can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
  • Capable of measuring the power consumption of the connected device in real time via smartphone, which allows you to save on electricity bills.
  • Voice support (Amazon Alexa & Google Assistant / Homey)
  • Works with push-button (momentary switch)
  • Support Repeater Role, Firmware OTA and SmartStart.
  • Suitable for 250W LED
  • Saves and restores the last status after a power failure
  • MIN and MAX light adjustment and dimming speed
  • Suitable for 90% of all LEDs
  • Does not require a neutral line, 3 wire connection available
  • Soft start system
  • Noiseless dimming

Specifications

Input voltage 230 Vac, 50Hz
Power (load) 250W LED 250W Halogen light bulbs
Suitable for Led-, halogen-, incandescent bulbs
Type dimmer R,C Phase cut
Working temperature 40 °C
Operation Push Dimming by Momentary Switch
Dimensions 45.145.119.8mm
Weight 35.4g

EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig2

Installation

Turn off the power

To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in the wires — before proceeding with the installation, be sure no voltage is present in the wiring. Take extra precautions to avoid accidentally turning the device on during installation.

Connect the device exactly according to the diagrams shown below

This dimmer is available for 2wire and 3-wire system. please note if it is 2wire, N and Load port must be connected to make stable dimming.
EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig3

Turn the power back

Operation

Min./Max./Dimming Speed adjustment
For the SMART dimmer to work optimally or suitable for your preference, you can adjust the brightness at the Min. and Max. level and also the dimming speed with the MIN./MAX./Dimming Speed adjustment.

  • MIN adjustment: Switch on the lights. When the lights are on, insert a screwdriver in MIN and turn to the left. When the light becomes unsteady, turn slightly back to the right so that the light remains steady.
  • MAX adjustment: Switch on the lights. When the lights are on, insert a screwdriver in MAX and turn to the right. When the light becomes unsteady, turn slightly back to the left so that the light remains steady.
  • Dimming Speed adjustment: Insert a screwdriver in Speed, clockwise to increase the dimming speed when you push the momentary switch, vice versa.

Z-Wave Setting

  1. SmartStart Inclusion
    SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
    A. Add the dimmer controller DSK into the primary controller SmartStart Provisioning List.
    (If your controller does not support SmartStart inclusion, please refer to the manual for your controller for non-SmartStart inclusion.).
    B. Power cycle once for dimmer controller.
    C. The dimmer controller will send “Explorer Auto inclusion” frame to start SmartStartInclusion.
    D. Wait a moment, the dimmer controller should be added to the controller.
    Note: The dimmer controller will SmartStart Inclusion when it is removed from a Z-Wave network.
    The Dimmer has a DSK string, you can key in first five digit to increment SmartStart process, or you can scan QR code. The QR code can be found on the Dimmer controller or in the box.
    DSK: 65286-19008-32952-20593- 44872-18102-41266-46651

  2. Add to the Z-Wave Network (Classic Inclusion)
    Step 1. Remove the device from previous Z-Wave network if it has already been added to, otherwise pairing mode will be fail.
    Step 2. Double Press the reset button.
    Step 3. The indicator will start blinking blue and stay solid for 10s when pairing succeed, timeout 15mins.
    EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig4

  3. Remove from a Z-Wave Network
    Method 1. From your Z-Wave hub interface, chose to remove or exclude the device as instructed.
    Method 2. Remove from the Device, see below instructions.
    Step 1. Press the reset button for 3 times.
    Step 2. The indicator will start blinking purple and stay solid purple and stay solid done, timeout 3mins.
    EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig5

  4. Factory Reset
    Step 1.
    Press the reset button for 5s.
    Step 2. When the Indicator stay in Red for 10s, reset finished.
    EcoDim Eco-Dim.10 Z-Wave Smart LED Dimmer Z-Wave 250W
fig6

Please Note:
This procedure should only be used when the primary controller is inoperable.
All configuration will be reset after the device is reset or remove from the network.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals