saxby 107137 Self Test Emergency Batten Kit Instruction Manual
- September 28, 2024
- saxby
Table of Contents
107137 Self Test Emergency Batten Kit
“`html
Product Specifications:
-
Product Models: RularPlus IP20, RularPro IP20, LED
Anti-Corrosive batten IP65 -
IP Rating: IP20 for RularPlus/RularPro, IP65 for LED
Anti-Corrosive batten -
Components: EM converter, EM battery, LED board, test switch,
indicator, one-way terminal, screws, nuts, 2 wires -
Screw Sizes: 4 x 10mm Screws for IP20, 4 x 8mm Screws for
IP65
Product Usage Instructions for RularPlus/RularPro IP20:
-
Ready all the EM kit accessories mentioned above.
-
Press down the metal frame of the rear base slightly and rotate
both ends to open the diffuser cover. -
Locate the EM converter and EM battery, ensuring their correct
placement. -
Secure the EM converter and EM battery to the light fitting
using screws. -
Attach the LED board to the PCB board with nuts.
-
Install the test switch and indicator securely.
-
Connect the wires of LED board, EM battery, test switch,
indicator to the corresponding positions on the EM converter. -
Wire the components as per the provided wiring diagram.
-
Re-close the diffuser cover into place.
Product Usage Instructions for LED Anti-Corrosive batten
IP65:
-
Prepare all the EM kit accessories as listed.
-
Open the diffuser cover by unfastening securing clips.
-
Locate and secure the EM converter and EM battery
correctly. -
Follow the wiring diagram to connect the components.
-
Clip the diffuser cover back into place.
Frequently Asked Questions (FAQ):
Q: Can I use the same components for both RularPlus/RularPro
IP20 and LED Anti-Corrosive batten IP65?
A: Yes, both products use similar components but have different IP ratings and installation procedures.
Q: What should I do if the indicator light is not working after
installation?
A: Check the wiring connections and ensure all components are securely attached according to the wiring diagram.
“`
Additional instructions
Instruction for RularPlus/RularPro IP20
2 11
Nut LED Board
EM Battery
7
6 3
8
3
10
See wiring details
9
4
LED Driver
Light Fitting
5
Test Switch
Indictaor EM Converter One-way Terminal
One-Way
Washers for Test Switch Clip for Indicator
2 Wires Terminal
4 x 10mm Screws for IP20 4 x 8mm Screws for IP65
1. Ready all the EM kit accessories: EM converter,
1
EM battery, LED board, test switch, indicator,
one-way terminal, screws, nut, 2 wires.
2. Press down the metal frame of rear base slightly
then rotate both ends of the product in the
direction of the arrow to open the diffuser cover.
3. Locate the EM converter and EM battery to the
holes, ensure the EM converter output is close
to the battery.
4. Secure the EM converter to the light fitting with 2 screws by screwdriver.
5. Secure the EM battery to the light fitting with 2 screws by screwdriver.
6. Secure the LED board to the PCB board with 2 white nuts, keep the out-wire is on backplate.
7. Pull the test switch through the hole then using 2 washers to secure.
8. Insert the clip into the hole for indicator, then insert the indicator through the clip to secure it.
9. Insert the wire of LED board, EM battery, test switch, indicator in the corresponding position on EM converter.
Test Switch Indicator Washers for Test Switch Clip for Indicator EM Battery
Nuts
EM Converter
LED Board
Indicator wires
EM battery wires Test switch wires
LED board wires
+-
Test switch Indicator
10. Wire as per the wiring diagram below:
Battery+/Indicator
Test switch LED board DC-
DC+
Battery
EM convertor N
Led –
L
Led +
L One-way terminal L
L
L
Earth
Terminal block
N
N
Permanent L
Switched L Earth Neutral
LED +-
N LED driver
L
11. Re-close diffuser cover into the place.
Instruction for LED Anti-Corrosive batten IP65
Clip for Indicator (Fitted) Indictaor
LED Board Nut
8 53 6 7
93 4
2 11
10
See wiring details
EM Battery Test Switch
EM Converter
Washers for Test Switch
One-Way 2 Wires Terminal
LED Driver
One-way Terminal
4 x 10mm Screws for IP20 4 x 8mm Screws for IP65
1
1. Ready all the EM kit accessories: EM converter, EM battery, LED board,
test switch, indicator, one-way terminal, screws, nut, 2 wires.
2. Open the diffuser cover by unfastening securing clips.
3. Locate the EM converter and EM battery to the holes, ensure the EM
converter output is close to the battery.
4. Secure the EM converter to the light fitting with 2 screws by screwdriver.
5. Secure the EM battery to the light fitting with 2 screws by screwdriver. 6.
Secure the LED board to the PCB board with 2 white nuts, keep the out-wire is
on backplate. 7. Screw the 2 washers into the test switch and place it on the
appropriate position of rear housing. 8. Insert the indicator into the clip to
secure it. 9. Insert the wires of LED board, EM battery, test switch,
indicator in the corresponding position on EM converter.
Light fitting
Test Switch Indicator Washers for Test Switch Clip for Indicator EM Battery
Nuts EM Converter LED Board
Indicator wires
EM battery wires Test switch wires
LED board wires
+-
Test switch Indicator
10. Wire as per the wiring diagram below:
Battery+/Indicator
Test switch LED board DC-
DC+
Battery
EM convertor N
Led –
L
Led +
L One-way terminal L
L
L
Earth
Terminal block
N
N
Permanent L
Switched L Earth Neutral
LED +-
N LED driver
L
11. Re-close diffuser cover by clipping it into place.
V1 17/06/2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>