OPT-J0537 Original Mimaki Bulk Ink System User Manual
- June 3, 2024
- Mimaki
Table of Contents
OPT-J0536 OPT-J0537 OPT-J0538 OPT-J0539
Additional heater option
User Manual
OPT-J0537 Original Mimaki Bulk Ink System
Foreword
Congratulations on your purchase of the additional heater option.
This operation manual
- This manual explains the operation of the additional heater option.
- Read and fully understand this operation manual before using this machine. It is also necessary to keep this operation manual on hand.
- Make arrangements to deliver this operation manual to the person in charge of the operation of the additional heater option.
- Although this operation manual has been carefully prepared for your easy understanding, please do not hesitate to contact your local distributor if you have any inquiry.
- The contents of this operation manual are subject to change for improvement without notice. Please note.
- If this manual should become illegible due to damage, or is destroyed due to fire or similar reason, purchase another copy of the operation manual at our sales office.
CAUTION
THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND
IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI
NEITHER ASSUMES NOR AUTHORIZES DEALERS TO ASSUME FOR IT ANY OTHER OBLIGATION
OR LIABILITY, OR MAKE ANY OTHER WARRANTY, OR MAKE ANY OTHER WARRANTY IN
CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI’S PRIOR WRITTEN CONSENT.
IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.
Safety Precautions
Symbols
In this document, symbols are used for explaining the contents of cautions on
operation. The symbol to be displayed differs depending on the caution
content. Understand the meaning of each symbol and use this machine safely and
correctly.
Examples of Symbols
Meaning
WARNING| WARNING| Failure to observe the instructions given with this
symbol can result in death or serious injuries to
personnel.
Be sure to read it carefully and use the printer properly.
---|---|---
CAUTION| CAUTION| Failure to observe the instructions given with this
symbol can result in minor or medium injuries to personnel.
| GENERAL WARNING| This symbol indicates that the items shown need to be
noted. Specific notes are drawn in the figure.
| GENERAL MANDATORY
ACTION| This symbol indicates that the action shown must be executed. Specific
instruction is shown in the illustration.
| GENERAL PROHIBITION| This symbol indicates that the action shown is
prohibited. Specific action that is prohibited is shown in the illustration.
| IMPORTANT| Important notes for the use of this unit are given with this
symbol. Refer to the operation.
| HINT| Useful information is given with this symbol. Refer to the operation.
| REFERENCE| This symbol indicates the reference page for related contents.
Click the text to display the orresponding page.
Cautions on Installation
Caution
Do not install in the following locations
- A location exposed to direct sunlight.
- On an inclined surface.
- A location that vibrates.
- A location exposed to a direct air flow from an air conditioner, etc.
- Around a location where fire is used.
- A location where the temperature or humidity changes significantly. (The recommended usage environment differs depending on the connected printer. Confirm by referring to the operation manual of the printer)
Warning for Use
Warning
Power supply precautions
- Use the power cable provided. Otherwise there is a risk of failure, electric shock, or fire. Do not use the power cable with other electronic devices.
- Always grasp the plug when unplugging the power cable. Pulling on the power cable itself may damage the cable and result in failure, electric shock, or fire.
- Do not use the power plug with dust on it. Otherwise there is a risk of failure, electric shock, or fire.
- Avoid touching the blade of the power plug with a metal object. Otherwise there is a risk of failure, electric shock, or fire.
- Do not attempt to modify the cable. Avoid damaging the cable. Avoid placing heavy objects on the power cable or pulling on or exposing the cable to heat. Doing so may damage the cable, resulting in electric shock or fire.
- Do not use extension cords or multi-outlet extension cords. Otherwise there is a risk of failure, electric shock, or fire.
- Do not use if the power cable appears to be damaged or the core wire
- Do not handle the power plug with wet hands. Disregarding this precaution may result in electric shock.
- Plug the power cable plug into a grounded power outlet. Otherwise there is a risk of failure, electric shock, or fire.
- When installing electrical outlets, perform grounding work to prevent electric shock accidents. All electrical work (Class C grounding work; formerly Type 3 grounding work) must be handled by a licensed electrician.
Precautions
Caution
Power Supply
- Use this machine with a power supply that meets specifications.
- Be sure to plug the power cable into a power outlet close to the machine. Insert the power plug blade securely.
- When connecting the power cable, check the input voltage of the power outlet and the capacity of the breaker. Also, connect each cable to a separate power source with an independent breaker.
Connecting to power outlets linked with the same breaker may trip the breaker.
Heater
- Do not spill liquid on the Media Transfer Surface as this may cause failure of the heater or firing.
- Do not touch heaters with bare hand while it is hot, otherwise, you can get burned.
- Do not spill liquid on the Media Transfer Surface as this may cause failure of the heater or firing.
- Do not touch heaters with bare hand while it is hot, otherwise, you can get burned.
- Condensation may form on the print head nozzle surface depending on the ambient temperature and humidity.The formation of condensation may cause ejection failures (e.g., nozzle clogging or deflection).
Perform head cleaning if any ejection failures (e.g., nozzle clogging or deflection) occur during printing. Set the print heater to a temperature not exceeding 35 °C, and ensure that the ambient temperature is within the permissible operating temperature range (20 °C to 30 °C).
Warning labels
Warning labels are stuck on the machine. Be sure to fully understand the
warning given on the labels.
If a warning label is illegible due to stains or has come off, purchase a new
one from a distributor or our sales office.
No. | Order No. | Label |
---|---|---|
1 | M910931 | |
2 | M907833 | |
3 | M903330 | |
4 | M903405 | |
5 | M907935 | |
6 | M905811 | |
7 | M913419 | |
8 | M905935 | |
9 | M903239 | |
10 | M906031 | |
11 | M910966 | • Make sure to connect the power-supply of the same voltage to |
inlet-1 and inlet-2.
Use the heater
- PRE (Pre-heater): Preheats the media before printing to suppress rapid temperature change.
- PRINT (Print heater): Helps prevent ink bleeding.
Turn on the heater
-
Switch the voltage selector switch to the voltage value to be used.
• The factory default setting is “220”. -
Check the power cable is plugged into the heater dedicated inlet to the UCJV300.
• In the foreground is the inlet for the heater (INLET2).
• Use only the accessory power cable.
• Connect the power cable to a power outlet near the unit so that it can be easily routed.
• Connect the plug of the power cable to an outlet with grounding polarity. Failure to do so may result in a malfunction of the unit, electric shock, or fire. -
Turn heater power switch ON.
• In the foreground is the power switch for the heater. Turn it to the “I” side.
Setting the Heater Temperature
Set the heater temperature according to the media you are using.
- The temperature can be changed even during printing.
- Depending on the ambient temperature, it may take several minutes to several tens of minutes to reach the set heater temperature.
- This printer should be used in an ambient temperature of 20°C~30°C. Depending on the operating environment and printing conditions, the heater temperature may not rise to the set value.
- Press the [ENTER] key to cancel the message display.
• The Heater Temperature Setup screen appears.
• In the factory default setting, the heater setting temperature is displayed as “- – -” and the heater is turned off.
• If [HEATER] is not displayed, press the [SEL] key to switch the function.
Enter the temperature for each heater and press the [ENTER] key.
-
Press key, and set the temperature for each heater. (Set value: OFF / 20~60 ℃ )
Selecting a heater: Press key.
Setting a temperature: Press key. -
Heater icon on the operation panel turns green if the heater temperature reaches the set value.
-
Printing is possible once the heater temperatures reach the temperature settings ±3 °C.
-
The heater temperature can also be changed from the setup menu.
-
The temperature can be changed while printing is in progress, but this may cause color variations to occur.
Press the [ENTER] key to complete.
- Exit the Heater Temperature Adjustment screen and return to Local.
Heater related error
If an error occurs in the heater option, a warning message will be displayed. When an abnormality occurs, take the following actions.
Display | Cause | Measures |
---|
702
THERMISTOR CONNECT| The thermistor connection of a heater is defective.| •Turn
off the power on the machine and turn it on after a while.
•When displaying again, contact your local distributor, our sales office, or
service center.
710
HEATER TEMP ERROR| The temperature abnormality of the heater has been
detected.When this error occurred and if the temperature abnormality cannot be
resolved, the power supply of the machine is forcibly turned off.| •Turn off
the power on the machine and turn it on after a while.
•When displaying again, contact your local distributor, our sales office, or
service center.
Specification
Item | Specification |
---|---|
OPT-J0536(160 size) | OPT-J0537(130 size) |
OPT-J0539(75 size)
Power supply specifications| Single-phase 100 to 120 V AC ±10 % / 12 A,
single-phase 200 to 240 V AC ±10 % / 8 A, 50/60 Hz ±1 Hz
Power consumption| 1,440 W (100 to 120 V AC), 1,920 W (200 to 240 V AC)×2 or
less
External dimensions
| Width| 2900mm| 2650mm| 2382mm| 2090mm
Depth| 776mm
Height| 1475mm
Weight| 188kg| 177kg| 161kg| 144kg
Refer to UCJV150/300 series for other specifications.
© MIMAKI ENGINEERING CO., LTD.2022
D203669-10-10102022
MIMAKI ENGINEERING CO., LTD.
https://mimaki.com/
https://japan.mimaki.com/
D203669-10