saxby 90957 Alto Recessed LED White 14w Ceiling Downlight Instruction Manual

saxby 90957 Alto Recessed LED White 14w Ceiling Downlight

Product Information

The Alto Recessed light fitting is a LED module (COB) that comes in three types – 14W, 24W, and 32W. The light source has an energy efficiency class of E or D. The power supply is double insulated and does not require connection to an Earth circuit. The product is not suitable for dimming. The light fitting should be cleaned with a soft dry cloth only, and solvents or abrasive cleaners should not be used as they could damage the finish.

Technical Data

• Supply Voltage: 220-240 V~, 50 Hz
• Bulb Type:
  • 90957 – 14W LED module (COB), 4000K
  • 90958 – 24W LED module (COB), 4000K
  • 90959 – 32W LED module (COB), 4000K
• Conformity: Conforms with all relevant UKCA Directive requirements and EC Directive requirements

Product Usage Instructions

1. Identify the wiring from your light fitting.
2. Pull the wire through the hole and connect it to the connector block inside the LED driver.
3. If there are any incoming earth cables, join them together and insulate them with good quality insulation tape to ensure earth continuity throughout your property.
4. Check that the wires are connected correctly and none are left out of the connection block.
5. The power supply is double insulated and does not require connection to an Earth circuit.
6. The product is not suitable for dimming.
7. For cleaning, use a soft dry cloth only. Do not use solvents or abrasive cleaners as they could damage the finish.
8. Always switch off the power supply before cleaning and disconnect the product from mains at least 10 minutes, allowing it to cool down before any maintenance or adjustment.
9. For further information, visit https://www.lighting-info.co.uk/90957.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note that the switch is turned off before installation.

Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.

• Cut a mounting hole in the ceiling taking care not to foul any pipes, mains cables or joists beneath the surface. 90957—– Cut hole: ø105mm / Minimum cavity depth: 63mm
  90958—– Cut hole: ø155mm / Minimum cavity depth: 82mm
  90959—– Cut hole: ø205mm / Minimum cavity depth: 102mm

• It is always recommended to cut the hole slightly smaller than the size specified, and then file the hole until the recessed unit fits snugly.

• Position the LED Driver next to mains outlet that the system will connect to do not connect at this stage.

• Pull the mains wire through the hole to wire as detailed wiring.

• Push the spring clips upwards and fit into the ceiling hole, then push the unit up until firmly in position, ensuring that no cables are trapped. Ensure that the product is sitting properly in the hole.

• Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Warning: This power supply is Double Insulated and does not require connection to an Earth circuit.

• Please read these instructions carefully before commencing any work
• This unit must be fitted by a competent and qualified electrician.
• Install in accordance with the IEE Wiring regulations and current Building Regulations.
• Check the pack and make sure you have all the parts listed.
• This system operates at Safety Extra Low Voltage, via the supplied LED driver, Never connect the light fittings directly to the mains without using the supplied LED driver.
• Always disconnect the LED driver from the mains when installing or maintaining this system.
• To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
• This light fitting should be connected to a fused circuit.
• If replacing an existing fitting, make a careful note of the connections.
• This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

• Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the LED Driver and each light fitting.
• Ensure that there is adequate ventilation for the LED Driver.
• Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
• The mains supply cable must have a minimum cross section area of 1.0mm2.
• Cables must be protected using suitable conduit or plastic trunking.
• The unit must be located a minimum distance of 100mm from a joist.
• The distance between units must be 0.5m minimum.
• This product must be mounted out of arms reach.

Wiring
Having correctly identified the wiring from your light fitting, pull the wire through the hole and connect to the connector block inside the LED driver in the following way:
This unit is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.

Technical data

• Supply: 220-240 V~, 50 Hz

• Voltage:

• Bulb: 90957–14W LED module (COB), 4000K This product contains a light source of energy efficiency class E.

• Type: 90958–24W LED module (COB), 4000K This product contains a light source of energy efficiency class D. 90959–32W LED module (COB), 4000K This product contains a light source of energy efficiency class E.

• Conformity with all relevant UKCA Directive requirements.

• Conformity with all relevant EC Directive requirements.

• The power supply is Double Insulated and does not require connection to an Earth circuit.

• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

• This product is not suitable for dimming.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.
Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.

For further information, please visit https://www.lighting-info.co.uk/90957
V2 20/12/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

www.saxbylighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>