BORMANN BWR5086 Cricopa Lago with Double Hook Instruction Manual

: September 28, 2024
: BORMANN

Table of Contents

BORMANN BWR5086 Cricopa Lago with Double Hook
Product Usage Instructions
OPERATING INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BORMANN BWR5086 Cricopa Lago with Double Hook

Specifications

Model: BWR5086 076810
Multi-Functional Uses: Recreational, Framing, Industrial, Emergency, Fencing, Strapping
Breaking Capacity: 1 TON – 4 TON
Cable Diameter: 4.5 mm – 5.5 mm
Leverage: 15:1 – 18:1

Product Usage Instructions

Tension Release
To release tension, follow these steps:

Release the pin spring in the direction of arrow A.
Firmly push the handle until the drive and stop flap are disengaged to remove the ratchet teeth.
Repeat handle movement as needed to release tension one notch at a time.

Apply pressure to the handle with a steady and even force to avoid sudden movements.

Raise Load or Apply Tension
To raise a load or apply tension:

Activate the drive wheel and ratchet wheel by pushing the pin spring in the direction of arrow A.
Lift the handle in the direction of arrow C to wind the cable and pull the load.

Extend the Cable
To extend the cable:

Secure the hook and pulley to a stable mooring base.
Push the drive pin spring in the direction of arrow B.
Lift the handle and hold it firmly in the direction of arrow E.
Push the stop flap in the direction of arrow D and simultaneously pull until desired slack is obtained.

Cable Replacement
To replace the cable:

Pull the entire cable from the ratchet wheel.
Remove the old cable from the upper opening and insert the new cable.
Wrap the new cable around the ratchet wheel.

FAQ

Q: Can this tool be used for lifting people?
A: No, do not lift people or lift over people using this tool.
Q: What should I do if I need maintenance or repair?
A: All repair, inspection, or replacement work must be carried out by technicians from the authorized service department of the manufacturer to ensure safety and warranty validity.
Q: Can I use non-provided equipment with this product?
A: No, always use the product with the supplied equipment to avoid malfunctions, serious injury, or death. The manufacturer and importer are not liable for damages resulting from non-conforming equipment usage.

OPERATING INSTRUCTIONS

Warning : Read the manual carefully before use. Failure to follow the warnings and instructions may result in tool damage, physical injury and/or damage to property. Store the manual in a safe place for future reference.

Multi-Functional Uses

Recreational
Framing
Industrial
Emergency
Fencing
Strapping

Tension Release
Release the pin spring in the direction of arrow “A”. Firmly push the handle until the drive and stop flap (not shown) are disengaged to remove the ratchet teeth. This releases the load by one notch. Repeat this handle movement as needed to release tension one notch at a time.

CAUTION

When releasing the load, avoid sudden movements of the handle.
Apply pressure to the handle with a steady and even force.

SPECIFICATIONS (BREAKING CAPACITY)

CABLE| METHOD| 1 TON| 1 – 1/2 TON| 2 TON| 3 TON| 4 TON
DOUBLE LINE| PULLING CAP.| 1000 Kgs| 1500 Kgs| 2000 Kgs| 3000 Kgs| 4000 Kgs
▪ Do not lift people or lift over people
SINGLE LINE| PULLING CAP.| 500 Kgs| 750 Kgs| 1000 Kgs| 1500 Kgs| 2000 Kgs
▪ Do not lift people or lift over people
CABLE DIAMETER| 4,5 mm| 4,5 mm| 4,5 mm| 4,8 mm| 5,5 mm
LEVERAGE| 15:1| 15:1| 16:1| 16:1| 18:1

TECHNICAL SPECIFICATIONS

Technical data

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

Raise Load or Apply Tension
Activate the drive wheel and ratchet wheel by pushing the pin spring in the direction of arrow “A” and then lift the handle in the direction of arrow “C”. Each movement of the handle will wind the cable to pull the load.

Extend the Cable
Secure the hook and pulley to a stable mooring base. Push the drive pin spring in the direction of arrow “B”. Lift the handle and hold it firmly in the direction of arrow “E”, then push the stop flap in the direction of arrow “D” and simultaneously pull until the desired slack is obtained.

CAUTION
Make sure your equipment is kept in safe and proper operating conditions by following these rules:

Inspect the cable regularly for fraying, kinks, twists, cut sections or distortions. The cable should be replaced as soon as one of the above conditions occurs.
Do not pull the cable up or around a corner.
Do not wrap the cord around any object and do not hook the cord back on itself.
Do not overload. You should know how much load is allowed when you pull.
Do not use a “cheater” or other method to lengthen the handle for additional leverage. This will damage the equipment itself.
Do not operate the puller with less than 3 cable wraps on the spindle.
Use a suitable strap, screw plug or other fitting connected to the load to be pulled. Ensure that there is positive engagement of the puller hook to the load.
Do not lift people or lift over people.

Cable Replacement
A keyhole-type opening specially designed for quick replacement in the ratchet wheel body and the swinging end on the cable allow for immediate, safe cable replacement.
Pull the entire cable from the ratchet wheel, pull the old cable out of the upper opening and insert the new cable, then wrap it around the ratchet wheel.

WWW.NIKOLAOUTOOLS.COM

The instructions manual is also available in digital format on our website www.nikolaoutools.com. Find it by entering the product code in the Search ” ” field.