BORMANN BAT6200 Concrete Nailing Gun With Spring Instruction Manual

September 28, 2024
BORMANN

BORMANN BAT6200 Concrete Nailing Gun With Spring

BORMANN BAT6200 Concrete Nailing Gun With Spring

SAFETY INSTRUCTIONS

Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in tool damage or physical injury. Store the manual in a safe place for future reference.

  • Do not press the nail tube by hand if there are nails in the tool.
  • Do not press the nail tube with both hands at the same time.
  • Do not hold the silencer sleeve with one hand when nailing.
  • Do not force the main sleeve axially when loading nails.
  • Do not use the tool in areas with flammable and/or explosive substances/objects .
  • Do not allow children and persons not familiar with these instructions to use the tool.
  • Before proceeding with disassembly, maintenance and cleaning of the tool, make sure that there is no nail left in the tool.
  • Wear personal protective equipment such as protective gloves, impact-resistant safety glasses and a safety helmet.
  • In case the tool fails to shoot a nail:
  1. Wait 5 seconds.
  2. Remove the tool from the working surface.
  3. Hold the tool’s handle with one hand and the silencing sleeve with the other.
  4. Pull the silencing sleeve to remove the nail from the tool.

TOOL COMPONENTS

  1. Silencing sleeve

  2. Nail tube
    2-1 Power adjustment screws

  3. Stroke needle tube

  4. Movable sleeve

  5. Return Spring

  6. Main Sleeve

  7. Striking needle

  8. Cylindrical pin

  9. Limit pin

  10. Striking needle bar

  11. Brake pin

  12. Brake pin spring

  13. Protective sleeve

  14. Firing spring
    Tool Components

TECHNICAL DATA

Model BAT6200
Length 375 mm
Applicable nail length range 19-45 mm
Driving depth adjustment 9 levels
Material Alloy steel
Noise 80 db
Weight 0.9 kg

OPERATION

  1. Place the tip of the tool perpendicular to the working surface.
  2. Push the grip to shoot a nail.

Attention: In case the tool overheats, stop using the tool and let it cool down.

Power adjustment (Fig. 2)

  1. Unscrew the silencing sleeve.
  2. Unscrew all adjusting screws to reduce power.
    Power adjustment

DISASSEMBLY

Note: Refer to section “Tool components”.

  1. Unscrew the grip assembly (16, 17).
  2. Take out the firing spring (14) and spring base (15).
  3. Remove the protective sleeve (13).
  4. Rotate the silencing sleeve (1) and nail tube (2) in order to remove them.
  5. Compress the main sleeve (6) and remove the limit pin (9).
  6. Press the brake pin {11) to separate the main sleeve (6) and the return spring (5) from the other components.
  7. Separate the movable sleeve (4) from the firing assembly and take out the whole firing assembly.
  8. Press the brake pin {11) and pull out the needle assembly, brake pin (11) and brake pin spring (12) at the same time.
  9. Remove the cylindrical pin (8) to separate the striking needle (7) from the striking needle bar (10).

ASSEMBLY

  • Follow the disassembly steps in reverse order.
  • Make sure that the tool has been assembled correctly before use.

MAINTENANCE

Periodic maintenance

  • After every 100 nail shots, remove the silencer sleeve to clean residue.
  • After every 200 nail shots, disassemble the tool and clean every part.

Maintenance during use

During use, if it found that the movable sleeve cannot slide:

  1. Stop using the tool and let it cool down.
  2. Disassemble the tool and check whether any parts are damaged.
  • If any part is damaged, do not assemble the tool. Make sure to replace the damaged parts before using the tool again.

  • The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/ illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.

  • To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

  • Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

CUSTOMER SUPPORT

WWW.NIKOLAOUTOOLS.COM
The instructions manual is also available in digital format on our website
www.nikolaoutools.com. Find it by entering the product code in the Search “ ” field.SymbolLogo
Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals