MODERN EMBER ME-AER36-SLIM Aerus Slim Linear Electric Fireplace Owner’s Manual

September 27, 2024
MODERN EMBER

MODERN EMBER ME-AER36-SLIM Aerus Slim Linear Electric Fireplace

Specifications

Model Number Dimensions
AER36-SLIM 36 [915mm] x 17-5/8 [448mm] x 4- 1/4 [108mm]
AER42-SLIM 42 [1067mm] x 17-5/8 [448mm] x 4- 1/4 [108mm]
AER50-SLIM 50 [1271mm] x 16- 1/2 [418mm] x 12-5/8 [320mm]
AER60-SLIM 60 [1525mm] x 34-1/2 [876mm] x 32-7/8 [834mm]
AER72-SLIM 72 [1830mm] x 70- 3/4 [1778mm] x 4- 1/4 [108mm]

Product Usage Instructions

Preparation

Tools Required

  • Wood Screws
  • Drywall Anchors
  • Wall Bracket

Parts Included

  • Decorative Crystals
  • Remote Control
  • Screw Covers
  • Driftwood Logs

Installation & Assembly

Step 1: Selecting Location
Your appliance is suitable for wall-mounted, recessed, and mantel installation. Choose a location away from moisture, drapes, furniture, and high traffic areas.

Step 2: Minimum Clearances
Ensure the following minimum clearances are maintained:

  • Bottom: 0 (0mm)
  • Sides: 0 (0mm)
  • Back: 0 (0mm)
  • Top: 11.8 (300mm) to mantel/ceiling

Frequently Asked Questions (FAQ)

  • Q: What should I do if the outlet or faceplate gets hot during use?
    A: Discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

  • Q: How should I handle the glass panel included with the product?
    A: Always use extreme caution when handling glass to prevent personal injury or property damage.

Aerus Slim
Linear Electric Fireplace

36” / 42” / 50” / 60” / 72” Wall Mounted / Built-in Electric Fireplace

Model :

  • ME-AER36-SLIM
  • ME-AER60-SLIM
  • ME-AER42-SLIM
  • ME-AER72-SLIM
  • ME-AER50-SLIM

OWNER’S MANUAL
AC 120V 60Hz 1465W (5000 BTUs)

Important Safety Instructions

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.

WARNING
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

  • This electric fireplace has a remote that requires a button battery that is hazardous to young children.
  • DO NOT let bare skin touch hot surfaces. This heater is hot when in use. To avoid burns, if provided, use handles when moving this heater. KEEP combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
  • EXTREME CAUTION is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
  • DO NOT operate any heater with a damaged cord or plug, after it has malfunctioned, or if it has been dropped or damaged in any manner. Discard the heater or return it to an authorized service facility for examination and/or repair.
  • DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.
  • CONNECT to properly grounded outlets ONLY.
  • DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock or fire, or damage the heater.
  • To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could cause a fire.
  • DO NOT use on soft surfaces, like a bed, where openings may become blocked.
  • DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored as heater has hot and arcing or sparking parts inside.
  • ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
  • DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
  • NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or come in contact with water.
  • AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
  • ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other surface, to use.
  • NEVER use a wall mount bracket from another manufacturer.
  • This product is not intended to be a primary heat source. It is for supplemental heat only.
  • INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
  • Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
  • ALWAYS turn this heater off before unplugging it from the outlet.
  • ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.
  • NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
  • ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
  • NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.
  • ALWAYS check your heater cord and plug connections with each use!
    1. MAKE SURE the plug fits tight in the outlet. Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
    2. Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
    3. During use, check frequently to see if the plug outlet or face plate is HOT.
    4. If the outlet or face plate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.
  • The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3- slot receptacle is not available, an adapter MUST be used.
    The adapter MUST be properly grounded to the outlet box (see figure below). [NOTE: Adapter NOT INCLUDED.]

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

Preparation

CAUTION
This product includes a GLASS panel! ALWAYS USE EXTREME CAUTION when handling glass. FAILURE to do so could result in personal injury or property damage.

  • Remove all parts and hardware from the carton and place them on a clean, soft, dry surface.
  • Parts and assembly steps are grouped for wall-hanging or recessing use.
  • Check the parts list to make sure nothing is missing.
  • Dispose of packaging materials properly. Please recycle whenever possible.

Tools

YOU WILL NEED THE FOLLOWING TOOLS (NOT INCLUDED):

  • Phillips Screwdriver
  • Stud Finder
  • Level
  • Tape Measure
  • Electric Drill
  • 1/4” Wood Drill Bit
  • Hammer

Parts & Hardware

Specifications & Dimensions

NOTE: Measurements are taken from the glass front

Installation & Assembly

Your appliance is a wall-mounted, recessed and/or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.

NOTE: Follow all National and local electrical codes.

MINIMUM CLEARANCE TO COMBUSTIBLES
NOTE: Measurements are taken from the glass front.

Bottom 0” (0mm)
Sides 0” (0mm)
Back 0” (0mm)
Top 11.8” (300mm) to mantel/ceiling

MINIMUM MANTEL CLEARANCES

WARNING
When using paint or lacquer to finish the mantel, the paint or lacquer must be heat resistant to prevent discoloration.

RECESSED INSTALLATION

STEP 1:
Prepare a wall with framed opening dimensions (Figure A) listed in the chart below.

Figure A

FRAMED OPENING SIZE

Model| W| H| D
ME-AER36-SLIM| 34- 3/4″ [884mm]| 16- 3/4″ [426mm]| 4″ [102mm]
ME-AER42-SLIM| 40- 3/4″ [1036mm]
ME-AER50-SLIM| 48- 3/4″ [1238mm]
ME-AER60-SLIM| 58- 3/4″ [1492mm]
ME-AER72-SLIM| 70- 3/4″ [1778mm]

RECESSED INSTALLATION

STEP 2:
Install the wall anchors in each side of the framed opening according to the dimensions in Figure B.

STEP 3:
Remove the screws from each side of the glass panel as shown in Figure C.

STEP 4:
WARNING! It is highly recommended that two people complete this step.
Remove the glass panel from the front of the fireplace (Figure D).

STEP 5:
Remove the two screws from each side (Figure E). Then, remove the two metal brackets from each side (Figure F).

STEP 6:
WARNING! It is highly recommended that two people complete this step.
Lift the fireplace and insert into the framed opening. Use your bubble level to level the fireplace within the framing and adjust as needed. Drive four screws through the mounting holes located on each side as shown in Figure G. Install the media and re-install the glass panel (Figure H).

WALL MOUNTED INSTALLATION

Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall.

Step 1: Select a location that is not prone to moisture and is located at least 36″ (914mm) away from combustible materials, such as curtains, drapes, furniture, bedding, paper, etc.
Step 2: Have two people position the appliance against the wall where it will be mounted. Use a bubble level to ensure the fireplace is level on the wall. Mark the location.
Step 3: Place the unit face down on a soft, non-abrasive surface. Remove the bracket from the back of the unit by removing the screws as shown in Figure I.
Step 4: CAUTION! It is highly recommended that the mounting bracket be screwed into wall studs whenever possible. If wall studs cannot be used, ensure that the supplied plastic anchors are used to affix the bracket to the wall and that the bracket is adequately secured. Mark the location of the screw locations on the wall. Then mount the bracket on the wall using the supplied screws. The bracket must have the hooks facing upward and be level. Step 5: With the wall mounting bracket installed, have two people lift the appliance and insert the two hooks on the bracket into the two slots on the back of the fireplace.
Step 6: Check the fireplace for stability, ensuring that the bracket will not pull free from the wall.

“L” SHAPE BRACKET INSTALLATION

Only Used For Wall Mounted Installation

Step 1. Remove the silver screw at the bottom of the appliance. Set the screw aside. Fig 1-1 Step 2.Using the screw previously removed, attach the L-bracket (supplied) to the bottom of the fireplace box. Fig 1-2 Step 3. Install the plastic anchor (B) into the drywall, then install the screw A (supplied) into the hole of the L-bracket into the wall anchor to secure the fireplace from coming off the bracket. Fig 1-3

HARD-WIRING INSTALLATION

WARNING
Turn off the appliance completely and let it cool down before servicing. Only a qualified service  person should service and repair this electric appliance.

Hard-Wiring Connection
If it is necessary to hard-wire this appliance, a qualified electrician must remove the cord connection and wire the appliance directly to the household wiring. The dedicated circuit and power supply breaker must be rated for 120V, minimum 15 amps. The appliance must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the current ANSI/NFPA 70 National Electrical Code in the United States.

NOTICE
There are 3 wires from the appliance junction: white (neutral), black (power L1), and red (ground) that connect to 120V power supply (break panel). See below.

  1. Remove the 2 securing screws from the junction box cover plate, located on the bottom left hand side of the appliance (Figure A).
  2. Install the strain relief to the junction box cover plate (located in hardware bag) (Figure B).
  3. Remove all the wires, and take out the existing cable plug. The power cord may be discarded.
  4. Take new cover plate supplied in the hardware bag and punch out the 7/8″ (22.2mm) hole. Feed wires through box connector. Connect the three wires (from outside) appropriately to the terminal connectors (Red (G) is ground, White (N) is neutral, and Black (L) is the hot/line connection (Figure C).
  5. Resecure the junction box cover plate using the 2 screws previously removed in step 1.

METAL SCREW COVER INSTALLATION

Place the two metal covers over the screws. Pre-installed magnets in the fireplace will keep the covers secure.

CRYSTAL / DRIFTWOOD LOGS INSTALLATION

  • Glass front must be removed and the appliance must be mounted in its final location before the crystal embers are installed.
  • Carefully place small crystal embers into the strip as shown in Figure J. Apply an even layer from side to side.
  • Randomly place the driftwood logs on top of the crystals as shown in Figure K.

Operation

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death.

POWER
Plug the power cord into an AC 120 Volt outlet (see IMPORTANT SAFETY INFORMATION on Page 2). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals