VISUAL COMFORT CO 700MDWRMT ModernRail Wall with Remote Transformer Installation Guide

VISUAL COMFORT CO 700MDWRMT ModernRail Wall with Remote Transformer

Specifications

• Product Name: ModernRail Wall with Remote Transformer
• Model Number: 920MDWALLR / 700MDWRMT_1.0
• Dimmable: Yes, with a low-voltage electronic dimmer
• Installation: Dry locations only, NEC compliant junction boxes
• Maximum Wattage: 32W per rail, up to 4 modules

Product Usage Instructions

Install the Fixture

1. Remove the canopy screws using the provided Allen Wrench.
2. Remove the mounting plate from the canopy.
3. Follow instructions provided with the remote transformer to bring power to the junction box.
4. Secure the mounting plate to the electrical box with the #8-32 screws provided.
5. Mark the anchor hole location for the lower arm on the wall using the provided diagram.
6. Ensure the mounting plate is level before continuing.
7. Insert and secure the anchor into the wall, then attach the anchor screw to the boss.
8. Connect the fixture to a suitable ground in accordance with local electrical codes.
9. Connect black fixture wire to blue (-) transformer wire and red fixture wire to red (+) transformer wire using wire nuts.
10. Secure the lower arm onto the boss using the set screw and Allen wrench.
11. Neatly place all wires and connections inside the canopy.
12. Align canopy holes with mounting plate holes and secure in place by tightening canopy screws.

Install the Module and Shade

1. Separate the two halves of the module and install the shade by screwing it into the base. Do not over-tighten.
2. Install the two module halves onto the rail and secure them together by screwing them together, matching polarity markings (+) and (-).
3. Repeat steps for remaining modules, ensuring a maximum of 4 modules or 32W per rail.

SAVE THESE INSTRUCTIONS!

FAQ

Q: Can this product be used in wet locations?

A: No, this product is suitable for dry locations only.

Q: What type of dimmer should be used with this product?

A: Use a low-voltage electronic dimmer for dimming functionality.

Q: How many modules can be installed per rail?

A: A maximum of 4 modules or 32W can be installed per rail.

Q: Is professional installation required?

A: It is recommended to have this product installed by a person familiar with construction and electrical hazards.

ENERALGPRODUCTINFORMATION

• These fixtures are intended to be installed utilizing
• NEC compliant junction boxes.
• This product is dimmable with a low-voltage electronic dimmer. This product is suitable for dry locations only.
• This instruction shows a typical installation.

CAUTION – RISK OF FIRE

This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.

Two Person Installation Recommended

Install the Fixture

1. Remove the canopy screws using the provided Allen Wrench.

2. Remove the mounting plate from the canopy.

3. Use the instructions provided with the remote transformer to bring power to the junction box.

4. Secure the mounting plate to the electrical box with the #8-32 screws provided.

5. Using the diagram above, mark the anchor hole location for the lower arm onto the wall. The fixture measure 39″ from the center of the upper arm to the center of the lower arm.

6. Verify that the mounting plate is level before continuing.
7. Line up an anchor tip with the marked location, and push the anchor into the wall up to the threads. Screw the anchor in the rest of the way with a Phillips-head screwdriver.
8. Slide the anchor screw through the boss, then screw it into the anchor.

9. Connect the fixture to a suitable ground in accordance with local electrical codes.

10. Connect the black fixture wire to the blue (-) transformer wire with a wire nut.

11. Connect the red fixture wire to the red (+) transformer wire with a wire nut.

12. Neatly place all wires and wire nut connections inside the canopy.

13. Align the canopy holes with the mounting plate holes.
    Secure the canopy in place by tightening the canopy screws using the provided Allen Wrench.

14. Place the lower arm onto the boss and secure them together by screwing in the set screw using the provided Allen wrench.

Install the Module and Shade

1. Separate the two halves of the module by unscrewing them from one another.

2. Install the two module halves onto the rail and secure in place by screwing them together. Make sure to match the polarity markings positive (+) and negative (-) on the rail.

3. Install the shade by screwing it into the base. Do not over-tighten. A maximum of 4 modules or 32W Max can be installed per rail.

4. Repeat steps 1-3 for remaining modules.

SAVE THESE INSTRUCTIONS!

7400 Linder Ave, Skokie, IL 160077
800.969.3347
www.visualcomfort.com
©2023 Visual Comfort & Co.. All rights reserved. The Visual Comfort & Co. logo is a registered trademark of Visual Comfort & Co. Visual Comfort & Co. reserves the right to change specifications for product improvements without notification

References

• Signature Designer Light Fixtures | Experience Visual Comfort & Co.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>