Securaco SSL-W-V1 Smart Lock User Manual

SMART LOCK INSTRUCTION

PACKING LIST

1. Main body1
2. Card1
3. mounting plate1
4. 20mm Gasket2
5. Clamp A1
6. Clamp B1| 7. Clamp Gasket1
8. 3mm Gasket2
9. 10mm Gasket1
10. Screws6
11. Allen Key1
12. Adhesion promoter1
---|---

MEET THE LOCK

INSTALLATION

1. Confirm the type of your lock.

Fission Lock

A1. Wipe the surface clean with adhesive promoter.

A2. Align the mounting plate into the card.

3. Align the center of the knob with the crossed red line, attach the mounting plate to the door, and remove the card.

A5. Install 4 AA batteries.

A4. Open the main body battery cover.

A6. Install the main body on the mounting plate.

A7.  Thin knob: Find the Clamp Gasket, fix it on the thin knob.

A8. Short knob: Open the knob of the main body, push out the Clamp A, insert the Clamp B, and then put the knob back to its original positioning.

A9. Lock the screws on both sides.

A10.  Close the battery cover and the hardware installation is complete.

Conjoined Lock
B1. Wipe the surface clean with adhesive promoter.

B2. Measure the thickness of the door lock, select the appropriate gasket and sticker, and attach it to the mounting plate.

B3. Remove the screw 1 cm out from the door lock, aim the mounting plate into the card, align the center of the knob with the crossed red line, attach the mounting plate to the door, remove the card, and lock the screw back to its original positioning.

B4. Open the main body battery cover.

B5. Install 4 AA batteries.

B6. Install the main body on the mounting plate.

B7. Thin knob: Find the Clamp Gasket, fix it on the thin knob.

B8. Short knob: Open the knob of the main body, push out the Clamp A, insert the Clamp B, and then put the knob back to its original positioning.

B9. Lock the screws on both sides.

B10. Close the battery cover and the hardware installation is complete.

2. Add smart lock in the app
2.1 Download the APP by scanning the QR code, or search “Smart Life” on App Store / Google Play. Create a new account or log in with an existing account.

https://smartapp.tuya.com/smartlife

2.2 Start the APP,Select “Add Device”.
2.3 Select “Auto Scan”, after you find the device, then click “Next”.
2.4 After the device is added, click “Done”.

NOTE| If you find that the rotation is opposite to the direction of the door lock, you can click the set icon and set the rotation direction to “anticlockwise unlock”.
---|---
The first time you open the door with APP, the device will calibrate the lock position. Please ensure that the device has been properly installed on the door lock.

3. Add smart lock to gateway
3.1 Select gateway in the APP, then click “ Add device by list”.
3.2 Select the smart lock device, and then click “OK”. When the pop-up box is displayed, select “Immediately to join”.
3.3 Select the device in the gateway sub-device list, then click “Opening / Closing ” to unlock and lock the door.

GUIDE FOR USE

1| Unlock/ Lock| A. Use the APP.
B. Turn the knob of the smart lock.
C. Use the keypad(accessory).
---|---|---
2| Rotation Direction| If you find that the rotation is opposite to the direction of the door lock, you can click the set icon and set the rotation direction to “anticlockwise unlock”.
3| Calibration| When the rotation is inaccurate during use, you can click “Setting / Calibration” for calibration in the APP.
4| Check battery| Select the device in the APP to check battery status.
5| Replace Clamp| Take off the Knob directly, press to take out the original Clamp, and replace another Clamp. You can take out the Clamp Gasket if necessary.
6| Beep alarm| There will be beeps when the device battery is low, and the battery needs to be replaced at this time.
7| Unbind device| Firstly, delete the device in the APP, then press “SET” button on the bottom of the battery case for 5 seconds until you hear a beep, the device is unbound.
8| Adjust height| If the door lock is too high, you can attach the gaskets to the mounting plate of the smart lock. First lock the screw holes in the diagram, then lock the other screw holes.
9| Share Device| A. At the bottom of the device page, click “ ” to enter member management.
B. Click “＋”at the top right of page and select “Family”to add.
C. Fill in the ohter APP account and other information, set the permissions, and click save.

PARAMETERS

WARNING
The battery may overheat if the following conditions occur, which may cause a fire or explosion hazard.
Battery dismantling, impacting, squeezing or putting into fire, soaking.
Contact metal or electrode short.

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>